scholarly journals Design of High Speed Data Transfer Direct Memory Access Controller for System on Chip Based Embedded Products

2015 ◽  
Vol 15 (3) ◽  
pp. 576-581 ◽  
Author(s):  
Abdullah Aljumah ◽  
Mohammed Altaf Ahmed
Keyword(s):  
High Speed ◽  
Data Transfer ◽  
Direct Memory Access ◽  
System On Chip ◽  
Memory Access ◽  
High Speed Data ◽  
On Chip

Research of USB OTG Technology in Image High-Speed Data Transfer

2014 ◽  
Vol 951 ◽  
pp. 261-264
Author(s):  
Miao Cao ◽  
Peng Yin
Keyword(s):  
High Speed ◽  
Data Transfer ◽  
Direct Memory Access ◽  
Control Unit ◽  
Ccd Camera ◽  
Storage Unit ◽  
High Speed Data ◽  
Fpga Chip ◽  
Compression Data ◽  
Access Data

In the high speed data transmission field, the mass data, which are obtained by high speed CCD camera, are compressed and stored in large capacity storage unit, and uploaded to the process control unit simultaneously. ISP1761,which is USB protocol chip, is introduced to actualize protocol transform, control Host/ Peripheral switchover, dominate up/down high speed data transfer with the contradiction of duplicative function of data compression board in the USB transfer. In order to give full play to the function of ISP1761, Virtex5 FPGA chip, which contains MicroBlaze function, is adopted to fulfill initialization and Direct Memory Access data transfer. High speed (52.4.8Mbps) compression data transfer is achieved.

Design and Verification of a Scalable Enhanced High Performance DMA Architecture for Complex SoC

2014 ◽  
Vol 556-562 ◽  
pp. 4303-4308
Author(s):  
Hua Long Zhao
Keyword(s):  
Image Quality ◽  
High Performance ◽  
Stream Processing ◽  
Direct Memory Access ◽  
System On Chip ◽  
Memory Access ◽  
High Data ◽  
Bandwidth Requirement ◽  
Chip Processing ◽  
On Chip

As the demand of higher image quality and greater processing capabilities are growing, obtaining higher data bandwidth for on-chip processing is becoming a more and more important issue. DMA (Direct Memory Access) component, as the key element in stream processing SoC (System on Chip) [1], should be deeply researched and designed to satisfy the high data bandwidth requirement of processing units. In this paper, we introduce a scalable high-performance DMA architecture for complex SoC to satisfy rigorous high sustained bandwidth and versatile functionality requirements. Several techniques and structures are proposed in this paper. A state-in-art verification environment is built for our design to fully verify its functionality. At the end of the paper, the tape-out results are provided. The whole implementation has been silicon proven to be functional and efficient.

scholarly journals An energy-aware system-on-chip architecture for intra prediction in HEVC standard

2019 ◽  
Vol 9 (6) ◽  
pp. 5084
Author(s):  
Abdessamad El Ansari ◽  
Anas Mansouri ◽  
Ali Ahaitouf
Keyword(s):  
Video Processing ◽  
High Speed ◽  
Intra Prediction ◽  
System On Chip ◽  
Memory Access ◽  
Hardware Accelerator ◽  
Energy Aware ◽  
High Efficient ◽  
On Chip ◽  
Technology Resources

<p>High resolution 4K and 8K are becoming the more used in video applications. Those resolutions are well supported in the new HEVC standard. Thus, embedded solutions such as development of dedicated ystems-On-Chips (SOC) to accelerate video processing on one chip instead of only software solutions are commendable. This paper proposes a novel parallel and high efficient hardware accelerator for the intra prediction block. This accelerator achieves a high-speed treatment due to pipelined processing units and parallel shaped architecture. The complexity of memory access is also reduced thanks to the proposed design with less increased power consumption. The implementation was performed on the 7 Series FPGA 28 nm technology resources on Zynq-7000 and results show, that the proposed architecture takes 16520 LUTs and can reach 143.65 MHz as a maximum frequency and it is able to support the throughput of 3840×2160 sequence at 90 frames per second.</p>

scholarly journals Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Nanophotonics ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 937-945
Author(s):  
Ruihuan Zhang ◽  
Yu He ◽  
Yong Zhang ◽  
Shaohua An ◽  
Qingming Zhu ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
High Performance ◽  
Pulse Amplitude ◽  
Telecommunication Networks ◽  
Low Power Consumption ◽  
Power Efficient ◽  
High Speed Data ◽  
On Chip

AbstractUltracompact and low-power-consumption optical switches are desired for high-performance telecommunication networks and data centers. Here, we demonstrate an on-chip power-efficient 2 × 2 thermo-optic switch unit by using a suspended photonic crystal nanobeam structure. A submilliwatt switching power of 0.15 mW is obtained with a tuning efficiency of 7.71 nm/mW in a compact footprint of 60 μm × 16 μm. The bandwidth of the switch is properly designed for a four-level pulse amplitude modulation signal with a 124 Gb/s raw data rate. To the best of our knowledge, the proposed switch is the most power-efficient resonator-based thermo-optic switch unit with the highest tuning efficiency and data ever reported.

scholarly journals Dual-shot dynamics and ultimate frequency of all-optical magnetic recording on GdFeCo

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Sicong Wang ◽  
Chen Wei ◽  
Yuanhua Feng ◽  
Hongkun Cao ◽  
Wenzhe Li ◽  
...  
Keyword(s):  
Magnetization Reversal ◽  
Energy Efficient ◽  
High Speed ◽  
Data Transfer ◽  
Laser Pulses ◽  
Time Resolved ◽  
All Optical ◽  
Fs Laser ◽  
High Speed Data ◽  
Natural Way

AbstractAlthough photonics presents the fastest and most energy-efficient method of data transfer, magnetism still offers the cheapest and most natural way to store data. The ultrafast and energy-efficient optical control of magnetism is presently a missing technological link that prevents us from reaching the next evolution in information processing. The discovery of all-optical magnetization reversal in GdFeCo with the help of 100 fs laser pulses has further aroused intense interest in this compelling problem. Although the applicability of this approach to high-speed data processing depends vitally on the maximum repetition rate of the switching, the latter remains virtually unknown. Here we experimentally unveil the ultimate frequency of repetitive all-optical magnetization reversal through time-resolved studies of the dual-shot magnetization dynamics in Gd27Fe63.87Co9.13. Varying the intensities of the shots and the shot-to-shot separation, we reveal the conditions for ultrafast writing and the fastest possible restoration of magnetic bits. It is shown that although magnetic writing launched by the first shot is completed after 100 ps, a reliable rewriting of the bit by the second shot requires separating the shots by at least 300 ps. Using two shots partially overlapping in space and minimally separated by 300 ps, we demonstrate an approach for GHz magnetic writing that can be scaled down to sizes below the diffraction limit.

scholarly journals Time-averaging of high-speed data transfer protocols

2005 ◽  
Vol 50 (12) ◽  
pp. 2065-2069 ◽  
Author(s):  
R. Marquez ◽  
E. Altman ◽  
S. Sole-Alvarez
Keyword(s):  
High Speed ◽  
Data Transfer ◽  
Time Averaging ◽  
High Speed Data

Optical Waveguides Embedded in PCBs - A Real World Application of 3D Structures Written by TPA

2007 ◽  
Vol 1054 ◽  
Author(s):  
Ruth Houbertz ◽  
Herbert Wolter ◽  
Volker Schmidt ◽  
Ladislav Kuna ◽  
Valentin Satzinger ◽  
...  
Keyword(s):  
Optical Fibers ◽  
Optical Waveguides ◽  
High Speed ◽  
Printed Circuit Boards ◽  
Data Transfer ◽  
Laser Pulses ◽  
Photon Absorption ◽  
Optical Data ◽  
Direct Laser ◽  
High Speed Data

ABSTRACTThe integration of optical interconnects in printed circuit boards (PCB) is a rapidly growing field worldwide due to a continuously increasing need for high-speed data transfer. There are any concepts discussed, among which are the integration of optical fibers or the generation of waveguides by UV lithography, embossing, or direct laser writing. The devices presented so far require many different materials and process steps, but particularly also highly-sophisticated assembly steps in order to couple the optoelectronic elements to the generated waveguides. In order to overcome these restrictions, an innovative approach is presented which allows the embedding of optoelectronic components and the generation of optical waveguides in only one optical material. This material is an inorganic-organic hybrid polymer, in which the waveguides are processed by two-photon absorption (TPA) processes, initiated by ultra-short laser pulses. In particular, due to this integration and the possibility ofin situpositioning the optical waveguides with respect to the optoelectronic components by the TPA process, no complex packaging or assembly is necessary. Thus, the number of necessary processing steps is significantly reduced, which also contributes to the saving of resources such as energy or solvents. The material properties and the underlying processes will be discussed with respect to optical data transfer in PCBs.

Design of Data Transfer System Based on PCI Express Interface Applied in High-Speed Railway

2012 ◽  
Vol 229-231 ◽  
pp. 1543-1546
Author(s):  
Xiao Bo Zhou ◽  
Min Xia ◽  
Hai Long Cheng
Keyword(s):  
Data Acquisition ◽  
Data Transmission ◽  
High Speed ◽  
Data Transfer ◽  
Transmission Method ◽  
High Speed Railway ◽  
Pci Express ◽  
Data Acquisition Card ◽  
High Speed Data Acquisition ◽  
High Speed Data

To improve data transmission performance of the data acquisition card, a design of high-speed data transmission system is proposed in the thesis. Using FPGA of programmable logic devices, adopting Verilog HDL of hardware description language, the design of modularization and DMA transmission method is implemented in FPGA. Eventually the design implements the data transmission with high-speed through PCI Express interface. Through simulation and verification based on hardware system, this design is proved to be feasible and can satisfy the performance requirements of data transmission in the high-speed data acquisition card applied in high-speed railway communication. The design also has some value of application and reference for a universal data acquisition card.

Detecting Malicious Switches for a Secure Software-defined Tactile Internet

2021 ◽  
Vol 21 (4) ◽  
pp. 1-23
Author(s):  
Bin Yuan ◽  
Chen Lin ◽  
Deqing Zou ◽  
Laurence Tianruo Yang ◽  
Hai Jin
Keyword(s):  
High Speed ◽  
Data Transfer ◽  
Low Cost ◽  
Rapid Development ◽  
Denial Of Service ◽  
Linear Structure ◽  
Network Layers ◽  
High Speed Data ◽  
Network Status ◽  
Sdn Controller

The rapid development of the Internet of Things has led to demand for high-speed data transformation. Serving this purpose is the Tactile Internet, which facilitates data transfer in extra-low latency. In particular, a Tactile Internet based on software-defined networking (SDN) has been broadly deployed because of the proven benefits of SDN in flexible and programmable network management. However, the vulnerabilities of SDN also threaten the security of the Tactile Internet. Specifically, an SDN controller relies on the network status (provided by the underlying switches) to make network decisions, e.g., calculating a routing path to deliver data in the Tactile Internet. Hence, the attackers can compromise the switches to jeopardize the SDN and further attack Tactile Internet systems. For example, an attacker can compromise switches to launch distributed denial-of-service attacks to overwhelm the SDN controller, which will disrupt all the applications in the Tactile Internet. In pursuit of a more secure Tactile Internet, the problem of abnormal SDN switches in the Tactile Internet is analyzed in this article, including the cause of abnormal switches and their influences on different network layers. Then we propose an approach that leverages the messages sent by all switches to identify abnormal switches, which adopts a linear structure to store historical messages at a relatively low cost. By mapping each flow message to the flow establishment model, our method can effectively identify malicious SDN switches in the Tactile Internet and thus enhance its security.

Sign in / Sign up

Export Citation Format

Share Document