Research on Cutting Tool Layout Method of Earth Pressure Balance Shield

2011 ◽  
Vol 47 (15) ◽  
pp. 161 ◽  
Author(s):  
Yi PU
Keyword(s):  
Cutting Tool ◽  
Earth Pressure ◽  
Pressure Balance ◽  
Earth Pressure Balance Shield ◽  
Earth Pressure Balance

Gray Relational Analysis of Graded Gravel Base Asphalt Pavement Structure

2011 ◽  
Vol 255-260 ◽  
pp. 3282-3286
Author(s):  
Xiu Shan Wang ◽  
Li Wang ◽  
Xiao Jun Ding
Keyword(s):  
Earth Pressure ◽  
Planetary Gear ◽  
Gray Relational Analysis ◽  
Stress And Strain ◽  
Pressure Balance ◽  
Joint Point ◽  
Earth Pressure Balance Shield ◽  
Earth Pressure Balance ◽  
Shield Machine ◽  
Increasing Load

The method to analysis the strength of planetary trains’ carriers of EPB(earth pressure balance) shield machine is presented in this paper. The structure of the shield machine trains is analyzed and the 3-D solid model of the carrier is built with Pro/E. After the load on the carrier has been dealt with, the strength of carrier is calculated by means of finite element method. The results via ANSYS show that the max stress and strain on the carriers are increasing as the increasing load on it. The max stress is lying on the joint point of the carrier and planetary gear shaft because of the bending deformation of the shaft.

Surface settlement during shield tunnelling at CH218 in Taipei

1998 ◽  
Vol 35 (1) ◽  
pp. 159-168 ◽  
Author(s):  
Chang-Yu Ou ◽  
Richard N Hwang ◽  
Wei-Jung Lai
Keyword(s):  
Ground Surface ◽  
Earth Pressure ◽  
Surface Settlement ◽  
Pressure Balance ◽  
Transit System ◽  
Ground Surface Settlement ◽  
Earth Pressure Balance Shield ◽  
Shield Tunnelling ◽  
Earth Pressure Balance ◽  
Twin Tunnels

This paper presents the surface settlement performance induced by the foamed type of earth pressure balance shield in contract CH218 of the Hsintien Line of the Taipei Rapid Transit System. The surface settlement characteristics caused by the single tunnel and by twin tunnels with reference to two sections spaced at 87 m are studied. Field observations indicate that the surface settlement trough due to the single tunnel can be represented by the normal distribution. The distance of the inflection point to the tunnel center and maximum surface settlement value are consistent with those found in the literature. The characteristics of the surface settlement trough are related to the type of the soil, particularly where the crown of the tunnel is located in a layered soil deposit. The ground surface settlement induced by twin tunnels was found to be larger than estimated using the principle of superposition.Key words: shield tunnelling, surface settlement, field observation.

Three-Dimensional Face Stability Analysis of EPBS Tunnels

2011 ◽  
Vol 378-379 ◽  
pp. 449-452
Author(s):  
Xue Gang Huang ◽  
Yu You Yang ◽  
Gui He Wang
Keyword(s):  
Three Dimensional ◽  
Earth Pressure ◽  
Pressure Balance ◽  
Circular Tunnel ◽  
Face Stability ◽  
Analysis Theory ◽  
The Face ◽  
Earth Pressure Balance Shield ◽  
Earth Pressure Balance ◽  
Kinematical Approach

A three-dimensional (3D) failure mechanism, based on the framework of the kinematical approach of limit analysis theory, is applied to calculate the face supporting pressure of a circular tunnel driven by the Earth Pressure Balance Shield (EPBS). The geometry of the mechanisms considered is composed of a sequence of truncated rigid cones. The numerical results obtained are presented.

The Finite Element Analysis of Piston under Thermal Load Based on UG/ANSYS

2012 ◽  
Vol 490-495 ◽  
pp. 2748-2751
Author(s):  
Li Zhi Wen ◽  
Zhi Wei Guan ◽  
Chen Fu Liu ◽  
Xi Tong Zhang
Keyword(s):  
Finite Element ◽  
Earth Pressure ◽  
Planetary Gear ◽  
Pressure Balance ◽  
Element Analysis ◽  
Joint Point ◽  
The Finite Element Analysis ◽  
Earth Pressure Balance Shield ◽  
Earth Pressure Balance ◽  
Shield Machine

The method to analysis the strength of planetary trains’ carriers of EPB(earth pressure balance) shield machine is presented in this paper. The structure of the shield machine trains is analyzed and the 3-D solid model of the carrier is built with Pro/E. After the load on the carrier has been dealt with, the strength of carrier is calculated by means of finite element method. The results via ANSYS show that the max stress and strain on the carriers are increasing as the increasing load on it. The max stress is lying on the joint point of the carrier and planetary gear shaft because of the bending deformation of the shaft

Sign in / Sign up

Export Citation Format

Share Document