ERROR ANALYSIS OF FINITE ELEMENT SIMULATING RESULTS OF MICRO DEEP DRAWING PROCESS BASED ON TAGUCHI METHOD

2006 ◽  
Vol 42 (09) ◽  
pp. 224
Author(s):  
Kaifeng ZHANG
Keyword(s):  
Finite Element ◽  
Taguchi Method ◽  
Error Analysis ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Micro Deep Drawing

Investigating the Effects of the Friction Coefficient and Tool Geometry on the Cup Thickness in the Deep Drawing Process of SPXI250 Alloy

2013 ◽  
Author(s):  
Iman Rostamsowlat ◽  
Ahmad Afsari ◽  
Maziar Janghorban
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Deep Drawing ◽  
The Other ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process ◽  
Simulation Results ◽  
Thickness Variations

In this paper, effects of friction coefficient and tool geometry on the thickness variations of a cylindrical cup were studied. Blank is made of SPXI250 alloy sheet which was analyzed by Finite Element Method (FEM). This not been studied yet. Finite Element modeling of the deep drawing process was conducted using ABAQUS/EXPLICIT software. A set of appropriate die and punch were designed for experimental tests. The results of the simulation showed that a change in the friction coefficient of the die-blank interface leads to a significant changes in the cup thickness. Moreover, the results revealed that the influence of die nose radius on the final cup thickness variations is greater than that of the punch nose radius. The simulation results of this study were compared with the experimental results and those of the other investigators’. The comparisons of the experimental and simulation results with those of the other researchers were so satisfactory.

FEM Simulation of Anisotropic Parameters Influencing the Earing in Sheet Metal Deep Drawing Process

2011 ◽  
Vol 88-89 ◽  
pp. 638-641 ◽  
Author(s):  
Lei Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Deep Drawing ◽  
Fem Simulation ◽  
Element Model ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Material Characteristics

Earing is often undesirable in the production of deep drawn containers because it results in a nonuniform cup height. A finite element model for earring analysis is developed considering only the flange area of the sheet. It was found that the draw-in depth of the flange increases with the increase of the r value, and it remains invariable when r value is larger than 2. With the increase of the r value, the max thickness decreases and the min thickness increases. If △r>0, four earings are formed. If △r =0, the material characteristics in all the planar directions are same. The flange uniformly flows into the die cavity, no earing is formed. If △r<0, four earings are formed. The earing distribution is dominated by r0, r45 and r90. Both r and △r have much effect on the earing distribution.

Mechanical and Laser Micro Deep Drawing

2007 ◽  
Vol 344 ◽  
pp. 799-806 ◽  
Author(s):  
H. Schulze Niehoff ◽  
Zhen Yu Hu ◽  
Frank Vollertsen
Keyword(s):  
Shock Wave ◽  
Size Effects ◽  
Deep Drawing ◽  
Thermal Stresses ◽  
Laser Forming ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Plasma Generation ◽  
Micro Deep Drawing ◽  
Explosive Forming

Mechanical micro deep drawing becomes a more and more industrial relevant process. But due to size effects new challenges are involved in this process compared to macro deep drawing. The size effects cause an increase of friction and thus hinder the material flow. The change of friction in mechanical micro deep drawing is subject of the presented investigations in this paper. Additionally to this, a new non-mechanical micro deep drawing process is presented, whereby a laser beam acts as a punch. This new laser deep drawing process is based on a totally different mechanism compared to thermal laser forming, e.g. forming by laser induced thermal stresses: The laser produces a pulse with an extremely high power density, which causes plasma generation at the target and thus a shock wave. The shock wave can be used as in explosive forming, but is smaller and easier to generate. Recent investigations showed that using this technology laser deep drawing is possible with a sheet metal out of Al 99.5 and a thickness of 50 'm. The deep drawing process was carried out with a die diameter of 4 mm and shows promising results.

The improvement in deep drawing process for producing air filter by using finite element method

2013 ◽  
Vol 40 (1) ◽  
pp. 125-130
Author(s):  
Trinet Yingsamphancharoen ◽  
Nakarin Srisuwan ◽  
Chira Densangarun
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Deep Drawing ◽  
Drawing Process ◽  
Air Filter ◽  
Deep Drawing Process ◽  
Element Method
Sign in / Sign up

Export Citation Format

Share Document