scholarly journals Use of computational fluid dynamics tools to calculate the dispersion of gas and aerosol emissions in conditions of a complex terrain

2021 ◽  
Vol 7 (1) ◽  
pp. 21-26
Author(s):  
Menaouer Mehdi ◽  
Mikhail P. Panin
Keyword(s):  
Reverse Flow ◽  
Air Flow ◽  
Ground Surface ◽  
Exposure Dose ◽  
Wind Tunnel Experiments ◽  
Ansys Fluent ◽  
Computational Region ◽  
Flow Vortex ◽  
Accelerated Flow ◽  
Aerosol Emissions

ANSYS FLUENT tools were used as part of a standard turbulence k-ε model to simulate the air flow around a number of typical obstacles (a solid cube, a solid hemisphere, and a 2D hill) which form a potential terrain in the NPP emission dispersion area and roughly correspond to the geometry of the buildings and structures within this area. For reproducibility, a non-uniform spatial grid is plotted in the computational region which condenses near the obstacle surface and the outer boundaries. The dimensions and the positions of the obstacles were chosen such that to ensure their best possible coincidence with the conditions of the published experiments. The result of simulating the velocity and direction of the air flow as the whole shows a good agreement with the data from the wind tunnel experiments in the areas in front of and over the obstacle, as well as in its air shadow. Typical accelerated flow, vortex, and reverse flow areas are reproduced reliably. There are variances observed only in the local heavy turbulence regions in the obstacle’s air shadow near the ground surface. All this indicates that it is possible to model in full scale the dispersion of the NPP emissions taking into account the peculiarities of the plant site terrain and the major onsite structures to determine more accurately the personnel and public exposure dose.

Numerical Analysis on the CO-NO Formation Production near Burner Throat in Swirling Flow Combustion System

2014 ◽  
Vol 69 (2) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd Jaafar
Keyword(s):  
Swirling Flow ◽  
Reverse Flow ◽  
Flow Behavior ◽  
Recirculation Region ◽  
Mixing Enhancement ◽  
Ansys Fluent ◽  
Pressure Losses ◽  
No Formation ◽  
Swirl Angle ◽  
Air Mixing

The main purpose of this paper is to study the Computational Fluid Dynamics (CFD) prediction on CO-NO formation production inside the combustor close to burner throat while varying the swirl angle of the radial swirler. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. A liquid fuel burner system with different radial air swirler with 280 mm inside diameter combustor of 1000 mm length has been investigated. Analysis were carried out using four different radial air swirlers having 30°, 40°, 50° and 60° vane angles. The flow behavior was investigated numerically using CFD solver Ansys Fluent. This study has provided characteristic insight into the formation and production of CO and pollutant NO inside the combustion chamber. Results show that the swirling action is augmented with the increase in the swirl angle, which leads to increase in the center core reverse flow, therefore reducing the CO and pollutant NO formation. The outcome of this work will help in finding out the optimum swirling angle which will lead to less emission.  

scholarly journals Numerical Modelling Of Humid Air Flow Around A Porous Body

2015 ◽  
Vol 9 (3) ◽  
pp. 161-166
Author(s):  
Aneta Bohojło-Wiśniewska
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Porous Medium ◽  
Numerical Modelling ◽  
Chinese Cabbage ◽  
Air Flow ◽  
Transfer Model ◽  
Humid Air ◽  
Ansys Fluent ◽  
Complex Heat Transfer

Summary This paper presents an example of humid air flow around a single head of Chinese cabbage under conditions of complex heat transfer. This kind of numerical simulation allows us to create a heat and humidity transfer model between the Chinese cabbage and the flowing humid air. The calculations utilize the heat transfer model in porous medium, which includes the temperature difference between the solid (vegetable tissue) and fluid (air) phases of the porous medium. Modelling and calculations were performed in ANSYS Fluent 14.5 software.

scholarly journals Calculated research of aeroelastic stability of a bridge over the river Ob in Salekhard at the stage of assembling and operation

2019 ◽  
Vol 6 (3) ◽  
Author(s):  
Anastasiya Shustikova ◽  
Andrei Kozichev ◽  
Sergei Paryshev ◽  
Konstantin Strelkov
Keyword(s):  
Cfd Simulation ◽  
Load Capacity ◽  
Air Flow ◽  
Lift Coefficient ◽  
High Strength ◽  
Railway Bridge ◽  
Aeroelastic Stability ◽  
Ansys Fluent ◽  
Long Span ◽  
Long Span Bridge

Recently, long span bridge construction has been demanded for development of the regions of the Russian Federation. In terms of economy, it’s useful to build a combined road-railway bridge. Such bridges, generally, constitute a metal cross-cutting girder with carriageways on lower, upper or both zones of the girder. The major advantages of combined bridges are high strength and load capacity, plus cross-cutting to wind load. Focus of this research is a combined road-railway bridge over the Ob river at the stage of assembling and operation. The purpose of the study was to determine the limits of aeroelastic stability of combined road-railway bridge at the stage of assembling and operation using numerical simulation. To better understand the bridges behaviour in air flow, flow around a section model has been researched with CFD simulation in the ANSYS FLUENT. Then based on the given results of the calculations the dependence of the bridge vibrations on wind speed within a specified range is obtained, and also values of drag coefficient Сх, lift coefficient Су and torque coefficient Мz are received. These studies were carried out in the range of angles of attack α = ±3°. The possibility of divergence and galloping was also estimated. The results of the study made it possible to estimate the influence of air flow on combined bridge cross-cutting girder. Overall, the conducted research seems promising for further investigation and development in the field of bridge aeroelasticity.

scholarly journals A coupled modelling effort to study the fate of contaminated sediments downstream of the Coles Hill deposit, Virginia, USA

2015 ◽  
Vol 367 ◽  
pp. 272-280 ◽  
Author(s):  
C. F. Castro-Bolinaga ◽  
E. R. Zavaleta ◽  
P. Diplas
Keyword(s):  
Sediment Transport ◽  
Transport Model ◽  
Uranium Deposit ◽  
Ground Surface ◽  
Ansys Fluent ◽  
Mining Site ◽  
One Dimensional ◽  
Coupled Modelling ◽  
Modelling Effort ◽  
Modelling Process

Abstract. This paper presents the preliminary results of a coupled modelling effort to study the fate of tailings (radioactive waste-by product) downstream of the Coles Hill uranium deposit located in Virginia, USA. The implementation of the overall modelling process includes a one-dimensional hydraulic model to qualitatively characterize the sediment transport process under severe flooding conditions downstream of the potential mining site, a two-dimensional ANSYS Fluent model to simulate the release of tailings from a containment cell located partially above the local ground surface into the nearby streams, and a one-dimensional finite-volume sediment transport model to examine the propagation of a tailings sediment pulse in the river network located downstream. The findings of this investigation aim to assist in estimating the potential impacts that tailings would have if they were transported into rivers and reservoirs located downstream of the Coles Hill deposit that serve as municipal drinking water supplies.

scholarly journals Heat Transfer Enhancement in Air Cooled Gas Turbine Blade Using

2021 ◽  
Vol 8 (3) ◽  
pp. 52-69
Author(s):  
Dr. Farhan Lafta Rashid Rashid ◽  
Dr. Haider Nadhom Azziz Azziz ◽  
Dr. Emad Qasem Hussein Hussein
Keyword(s):  
Temperature Distribution ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Air Temperature ◽  
Air Flow ◽  
Three Dimensions ◽  
Internal Diameter ◽  
Wall Surface ◽  
Gas Turbine Blade ◽  
Ansys Fluent

In this paper, an investigation of using corrugated passages instead of circular crosssection passages was achieved in conditions simulate the case in the gas turbine blade coolingusing ANSYS Fluent version (14.5) with Boundary conditions: inlet coolant air temperature of300 K with different air flow Reynolds numbers (191000, 286000 and 382000). Thesurrounding constant hot air temperatures was (1700 K). The numerical simulations was done bysolving the governing equations (Continuity, Reynolds Averaging Navier-stokes and Energyequation) using (k-ε) model in three dimensions by using the FLUENT version (14.5). Thepresent case was simulated by using corrugated passage of 3 m long, internal diameter of 0.3 m,0.01 m groove height and wall thickness of 0.01 m, was compared with circular cross sectionpipe for the same length, diameter and thickness. The temperature, velocity distributioncontours, cooling air temperature distribution, the inner wall surface temperature, and thermalperformance factor at the two passages centerline are presented in this paper. The coolant airtemperature at the corrugated passage centerline was higher than that for circular one by(12.3%), the temperature distribution for the inner wall surface for the corrugated passage islower than circular one by (4.88 %). The coolant air flow velocity seems to be accelerated anddecelerated through the corrugated passage, so it was shown that the thermal performance factoralong the corrugated passage is larger than 1, this is due to the fact that the corrugated wallscreate turbulent conditions and increasing thermal surface area, and thus increasing heat transfercoefficient than the circular case.

Wind tunnel experiments of air flow patterns over nabkhas modeled after those from the Hotan River basin, Xinjiang, China (II): Vegetated

2008 ◽  
Vol 2 (3) ◽  
pp. 340-345 ◽  
Author(s):  
Zhizhong Li ◽  
Shengli Wu ◽  
Janis Dale ◽  
Lin Ge ◽  
Mudan He ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
River Basin ◽  
Air Flow ◽  
Flow Patterns ◽  
Wind Tunnel Experiments

Numerical investigation on vibration and pressure fluctuation characteristics in a centrifugal pump under low flow rate

2020 ◽  
pp. 095440622096972
Author(s):  
Like Wang ◽  
Jinling Lu ◽  
Weili Liao ◽  
Pengcheng Guo ◽  
Guojun Zhu ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuation ◽  
Reverse Flow ◽  
Leading Edge ◽  
Low Flow ◽  
Main Shaft ◽  
Unstable Flow ◽  
Tip Leakage ◽  
Flow Vortex ◽  
Tip Separation Vortex

Vibration characteristic is an important factor in evaluating operation stability of centrifugal pump. The vibration of main shaft was measured using a laser vibrometer, internal flow field was simulated via the shear stress transport turbulence model, and distribution law of vibration and pressure fluctuation in the impeller were analysed to explore the induction factor of vibration and the inherent relationship with pressure fluctuation in a semi-open centrifugal pump under low flow rate condition. Results of the numerical simulation are consistent with the experimental data. In addition to rotation frequency caused by impeller rotation, vibration frequency also includes characteristic frequency with high amplitude induced by unstable flow. The complex vortex in the impeller is composed of tip leakage vortex (TLV), reverse flow vortex, passage vortex and tip separation vortex. The primary tip leakage vortex (PTLV) formed by the streamline spills from 0 to 0.2λ where λ is the dimensionless distance from leading edge to trailing edge collides with tip leakage flow, the leading edge overflow and reverse flow vortex at the frequency of 1.6 fn ( fn is the rotating frequency) and 2.2 fn appear, respectively. The tip separation vortex formed in the tip clearance induced a frequency of 1.2 fn. The frequency of unstable flow phenomenon was consistent with the vibration frequency of main shaft, which induced the vibration of centrifugal pump.

Some Experiments on the Reattachment of a Laminar Boundary Layer Separating From a Rearward Facing Step on a Flat Plate Aerofoil

1960 ◽  
Vol 64 (599) ◽  
pp. 668-672 ◽  
Author(s):  
T. W. F. Moore
Keyword(s):  
Boundary Layer ◽  
Liquid Film ◽  
Flat Plate ◽  
Laminar Boundary Layer ◽  
Reverse Flow ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Pressure Measurements ◽  
Flow Vortex

Summary:The results of experiments on the reattachment of a laminar boundary layer, separating from a rearward facing step in a flat plate aerofoil, are correlated with the properties of the short leading edge bubble which forms on thin aerofoils near the stall.The experiments, comprising pressure measurements, Pitot explorations, liquid film and smoke studies, indicate that for all Reynolds numbers above the value given by the Owen-KIanfer criterion the reattachment is turbulent behind a stationary air reverse flow vortex bubble. It is also found that the reattachment is laminar for Reynolds numbers below the critical, which further supports Crabtree's interpretation of the Owen-KIanfer criterion in terms of the condition for the growth of turbulent bursts.

scholarly journals Comparison of RANS and scale-resolving approaches when modelling the turbulent flow behind a bluff body

2019 ◽  
Vol 196 ◽  
pp. 00036
Author(s):  
Svetlana V. Pogudalina ◽  
Natalya N. Fedorova ◽  
Svetlana A. Valger
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Numerical Calculation ◽  
Turbulent Flow ◽  
Bluff Body ◽  
Air Flow ◽  
Ansys Fluent ◽  
Fluent Software

In this paper, the results of a numerical simulation of the air flow in the vicinity of a parallelepiped fixed on a plate are presented. The 3D calculations were performed with the ANSYS Fluent software using scale-resolving DES approach. The obtained results are compared with the experimental data and with the results of the previous numerical calculation.

An Evaluation of Drag Coefficient of Wind Turbine System Installed on Moving Car

2014 ◽  
Vol 660 ◽  
pp. 689-693 ◽  
Author(s):  
Mohd Sofian ◽  
Rosly Nurhayati ◽  
A.Jamit Rexca ◽  
S. Shamsudin Syariful ◽  
Abdullah Aslam
Keyword(s):  
Drag Coefficient ◽  
Wind Turbine ◽  
Air Flow ◽  
Aerodynamic Performance ◽  
Ansys Fluent ◽  
Car Body ◽  
Wind Turbine System ◽  
Fluent Software ◽  
Suitable Area

This study presents a simulation result of an evaluation of the aerodynamic performance of a moving car with a wind turbine system. Sedan type cars (approaching the size of Proton Wira car) were modeled using the SolidWork software and simulation was done by ANSYS FLUENT software. Three car models with different wind turbine system positions (in front of the front bumper, on top of the hood and on top of the roof) plus one model without the wind turbine system were simulated. The study proved that the position of the wind turbine system installation will change the characteristic of the air flow around the car body and affects the aerodynamic performance of the car. Extended front bumper of a car is not significantly affecting the aerodynamic performance of the car. This extended bumper seems to be the suitable area to install a wind turbine system and the investigation shows that the aerodynamic performance of the car improved due to lower drag coefficient, Cd..

Sign in / Sign up

Export Citation Format

Share Document