scholarly journals RESEARCH OF NON-UNIFORM ROTATION OF SHIP POWER PLANT ELEMENTS DRIVE

2020 ◽  
pp. 71-79
Author(s):  
Victor I. Kochergin ◽  
Sergey P. Glushkov ◽  
Aleksandr V. Kurmygin
Keyword(s):  
Power Plants ◽  
Combustion Engine ◽  
Uniform Rotation ◽  
Resonant Frequencies ◽  
Fuel Pump ◽  
Calculation Of Parameters ◽  
Speed Controller ◽  
Operating Rules ◽  
Additional Equipment ◽  
Operational Failures

This article contains the results of studies of the rotation unevenness parameters of the ship power plants elements drive. Theoretical prerequisites of such analysis are described and an example of calculation of parameters of torsional-oscillating system of high-pressure fuel pump drive and speed controller is given in the article. Calculations have shown that at the nominal crankshaft speed of the internal combustion engine, the possibility of resonant oscillations of the camshaft of the fuel pump is not excluded. Design features, faults, violation of adjustments or operating rules can contribute to the operation of elements of power plants at resonant frequencies and cause operational failures. Analysis of rotation unevenness of elements drive and additional equipment of ship's power plants is an appropriate technical measure that allows to increase the reliability of ship's power plants.

АКУСТИЧНА ПОМІТНІСТЬ БЕЗПІЛОТНИХ ЛІТАЛЬНИХ АПАРАТІВ З СИЛОВИМИ УСТАНОВКАМИ НА БАЗІ ПОРШНЕВИХ ДВИГУНІВ

2020 ◽  
pp. 62-80
Author(s):  
В. В. Руденко ◽  
И. В. Калужинов ◽  
Н. А. Андрущенко
Keyword(s):  
Control System ◽  
Internal Combustion Engine ◽  
Power Plants ◽  
Combustion Engine ◽  
Spectral Characteristics ◽  
Experimental Studies ◽  
Internal Combustion ◽  
Detection Range ◽  
Acoustic Signature ◽  
Static Conditions

The presence in operation of many prototypes of UAVs with propeller propellers, the use of such devices at relatively low altitudes and flight speeds makes the problem of noise reduction from UAVs urgent both from the point of view of acoustic imperceptibility and ecology.The aim of the work is to determine a set of methods that help to reduce the visibility of UAVs in the acoustic range. It is shown that the main source of noise from the UAV on the ground is the power plant, which includes the engine and the propeller. The parameters of the power plants influencing the processes that determine the acoustic signature of the UAV were investigated. A comprehensive analysis of the factors affecting visibility was carried out. The power plants include two-stroke and four-stroke engines, internal combustion and two-blade propellers. The use of silencers on the exhaust of the internal combustion engine was considered. The spectral characteristics of the acoustic fields of the propeller-driven power plants for the operating sample of the UAV "Eco" were obtained. The measurements were carried out in one-third octave and 1/48 octave frequency bands under static conditions. The venue is the KhAI airfield. Note that the propellers that were part of the power plants operated at Reynolds numbers (Re0,75<2*105), which can significantly affect its aerodynamic and acoustic characteristics. It is shown that when choosing a UAV control system, one should take into account the fact that two-stroke piston engines are the dominant source in the noise of propeller-driven control systems in the absence of a hood and mufflers in the intake and exhaust tracts. The use of a four-stroke internal combustion engine significantly reduces the noise of the control system. In the general case, the position of the boundaries of the zone of acoustic visibility of a UAV at the location of the observer is determined by the ratio between the intensity of acoustic radiation perceived by the observer from the UAV and the intensity of sound corresponding to the natural acoustic background and depends on the degree of manifestation of acoustic effects accompanying the propagation of sound in a turbulent atmosphere - the refraction of sound waves. Absorption and dissipation of acoustic energy. The calculation and comparison of the UAV detection range was carried out taking into account the existing natural maskers.The results of experimental studies are presented that allow assessing the degree of acoustic signature of the UAV. A set of measures aimed at reducing the intensity of the acoustic signature of the UAV in various regions of the radiation spectrum has been determined.

Effect of Chemical Hythane Composition on Pressure in Combustion Chamber of Engine

2019 ◽  
pp. 36-42
Author(s):  
A. P. Shaikin ◽  
I. R. Galiev
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Power Plants ◽  
Engine Speed ◽  
Combustion Engine ◽  
Fuel Mixture ◽  
Maximum Pressure ◽  
Chamber Volume ◽  
Excess Air ◽  
Scientific Papers

The article analyzes the influence of chemical composition of hythane (a mixture of natural gas with hydrogen) on pressure in an engine combustion chamber. A review of the literature has showed the relevance of using hythane in transport energy industry, and also revealed a number of scientific papers devoted to studying the effect of hythane on environmental and traction-dynamic characteristics of the engine. We have studied a single-cylinder spark-ignited internal combustion engine. In the experiments, the varying factors are: engine speed (600 and 900 min-1), excess air ratio and hydrogen concentration in natural gas which are 29, 47 and 58% (volume).The article shows that at idling engine speed maximum pressure in combustion chamber depends on excess air ratio and proportion hydrogen in the air-fuel mixture – the poorer air-fuel mixture and greater addition of hydrogen is, the more intense pressure increases. The positive effect of hydrogen on pressure is explained by the fact that addition of hydrogen contributes to increase in heat of combustion fuel and rate propagation of the flame. As a result, during combustion, more heat is released, and the fuel itself burns in a smaller volume. Thus, the addition of hydrogen can ensure stable combustion of a lean air-fuel mixture without loss of engine power. Moreover, the article shows that, despite the change in engine speed, addition of hydrogen, excess air ratio, type of fuel (natural gas and gasoline), there is a power-law dependence of the maximum pressure in engine cylinder on combustion chamber volume. Processing and analysis of the results of the foreign and domestic researchers have showed that patterns we discovered are applicable to engines of different designs, operating at different speeds and using different hydrocarbon fuels. The results research presented allow us to reduce the time and material costs when creating new power plants using hythane and meeting modern requirements for power, economy and toxicity.

scholarly journals Experimental Study of Pipes Shape Effect on Noise Reduction

2017 ◽  
Vol 5 (1) ◽  
pp. 71-86
Author(s):  
Muna S. Kassim ◽  
Ammar Fadhil Hussein Al-Maliki
Keyword(s):  
Experimental Study ◽  
High Pressure ◽  
Noise Reduction ◽  
Power Plants ◽  
Combustion Engine ◽  
Exhaust System ◽  
Noise Pollution ◽  
Shape Effect ◽  
Pipe Length ◽  
Exhaust Noise

Internal combustion engine is a major source of noise pollution. These engines are used for various purposes such as, in power plants, automobiles, locomotives, and in various manufacturing machineries. The noise is caused by two reasons; the first reason is the pulses which created when the burst of high pressure gas suddenly enters the exhaust system, while the second reason is the friction of various parts of the engine where the exhaust noise is the most dominant. The limitation of the noise caused by the exhaust system is accomplished by the use of silencers and mufflers. The aim of this study is the reduction of the noise by changing its inlet and outlet pipe length and shape. Also the losses in noise for different length and shapes have been investigated experimentally. The results show that the corrugated pipe is preferable for noise reduction.

scholarly journals Selection of damping coefficient of simplified mount module to control transmissibility of environmental response under nobase mass-block

2018 ◽  
Vol 7 (2.12) ◽  
pp. 151
Author(s):  
Gee Soo Lee ◽  
Moo Yeon Lee ◽  
Ki Hyun Kim ◽  
Chan Jung Kim
Keyword(s):  
Electric Power ◽  
Power Plants ◽  
Combustion Engine ◽  
Spectral Response ◽  
Design Criterion ◽  
Environmental Response ◽  
Operation Condition ◽  
Response Level ◽  
Electric Power Plants ◽  
Selection Of

Background/Objectives: This paper focused on the simplified design of passive mount modulein electric power plants using only spring and damper elements.Methods/Statistical analysis: The selection of elements in a proposed simplified passive mount module was proceeded under the requirement, which is to show the response level same or less as compare to the case of current mount module. The response at the upper location of mount affect to negative effect on the responsible electric power plants so the design criterion should be satisfied with the newly proposed simple mount module.Findings: The frequency response function between the force and response acceleration at upper position of mount module was calculated from the theoretical mount module and the transmissibility function, between two response accelerations at two different passive mount modules, was evaluated for interesting harmonic frequencies (from 1X to 4X). The primary interesting frequency(X)was determined at 30(Hz) since the operation condition of the combustion engine in electric power plant is scheduled to be operated at constant 1,800(rev/min). Several simulation cases can be obtained for different combination of selected dampingcoefficients at the proposed mount module. The magnitude of transmissibility function should be less than one all interesting frequencies and the reasonable condition of the simple mount module can be derived from the simulation result.Then, the validation of the designed simplified mount module was conducted by preparing two kinds of mount module and the acceleration responses were measured at 1,800(rev/min) operation under 100% electric load. The spectral response at interesting frequencies confirms the superiority of the newly proposed mount module.Improvements/Applications: The simplified structure of mount module can be possible to save installation cost and time simultaneously and it is easy to conduct the maintenance of mount module.  

Possibility of using gas lubricant in the cylinders of internal combustion engines of transport vehicles

2021 ◽  
pp. 13-20
Author(s):  
Keyword(s):  
Internal Combustion Engine ◽  
Bearing Capacity ◽  
Power Plants ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Engine Piston ◽  
Suspension Stiffness ◽  
Gas Layer

The prospects of using the gas-static suspension of the internal combustion engine piston in transport vehicles and power plants are considered. The diagram of the piston and the method for calculating the stiffness and bearing capacity of the gas layer surrounding the piston are presented, as well as the results of experiments that showed the relevance of this method. The possibility of gas and static centering of the engine piston is confirmed. Keywords: internal combustion engine, piston, gasstatic suspension, stiffness, bearing capacity, gas medium. [email protected]

New Free-Piston Topping Cycle for Gas-Turbine Power Plants

2003 ◽  
Author(s):  
William L. Kopko ◽  
John S. Hoffman
Keyword(s):  
High Performance ◽  
Power Plants ◽  
Waste Heat ◽  
Combustion Engine ◽  
Complete Recovery ◽  
Combined Cycle ◽  
Piston Engine ◽  
Free Piston ◽  
Free Piston Engine ◽  
Topping Cycle

A proposed topping cycle inserts a free-piston internal-combustion engine between the compressor and the combustor of a combustion turbine. The topping cycle diverts air from the compressor to supercharge the free-piston engine. Because the free-piston engine uses gas bearings to support the piston and is built of high-temperature materials, the engine can increase the pressure and temperature of the gas, exhausting it to a small expander that produces power. The exhaust from the topping-cycle expander is at a pressure that can be re-introduced to the main turbine, allowing almost complete recovery of waste heat. A capacity increase exceeding 35% is possible, and overall cycle efficiency can approach 70% when incorporated into a state-of-the-art combined-cycle plant. The cost of per incremental kW of the topping cycle can be dramatically lower than that of the base turbine because of the high power density and simplicity of the engine. Building on decades of progress in combustion turbines systems, the new cycle promises high performance without the engineering risks of manufacturing a completely new cycle.

CO2 Emission Abatement in IGCC Power Plants by Semiclosed Cycles: Part B—With Air-Blown Combustion and CO2 Physical Absorption

1999 ◽  
Vol 121 (4) ◽  
pp. 642-648 ◽  
Author(s):  
P. Chiesa ◽  
G. Lozza
Keyword(s):  
Power Plants ◽  
Pressure Ratio ◽  
Co2 Concentration ◽  
Absorption Process ◽  
Combustion Gases ◽  
Additional Equipment ◽  
Physical Absorption ◽  
Previous Solution ◽  
The One ◽  
The Impact

This paper analyzes the fundamentals of IGCC power plants with carbon dioxide removal systems, by a cycle configuration alternative to the one discussed in Part A (with oxygen-blown combustion). The idea behind this proposal is to overcome the major drawbacks of the previous solution (large oxygen consumption and re-design of the gas turbine unit), by means of a semiclosed cycle using air as the oxidizer. Consequently, combustion gases are largely diluted by nitrogen and cannot be simply compressed to produce liquefied CO2 for storage or disposal. However, CO2 concentration remains high enough to make separation possible by a physical absorption process. It requires a re-pressurization of the flow subtracted from the cycle, with relevant consequences on the plant energy balance. The configuration and the thermodynamic performance of this plant concept are extensively addressed in the paper. As in the first part, the influence of the pressure ratio is discussed, but values similar to the ones adopted in commercial heavy-duty machines provided here acceptable performance. Proper attention was paid to the impact of the absorption process on the energy consumption. The resulting net overall efficiency is again in the 38–39 percent range, with assumptions fully comparable to the ones of Part A. Finally, we demonstrated that the present scheme enables the use of unmodified machines, but large additional equipment is required for exhausts treatment and CO2 separation. A final comparison between the two semiclosed cycle concepts was therefore addressed.

SOFTWARE DEVELOPMENT FOR ESTIMATION OF LOW FREQUENCY SOUND PROPAGATION IN GAS GUIDES OF POWER PLANTS TAKING TO ACCOUNT ACTIVE SOUND SOURCES

2020 ◽  
Vol 5 (4) ◽  
pp. 36-44
Author(s):  
A V Vasilyev
Keyword(s):  
Sound Source ◽  
Power Plants ◽  
Sound Propagation ◽  
Combustion Engine ◽  
Source Parameters ◽  
Low Frequency ◽  
Sound Sources ◽  
Software Application ◽  
Frequency Sound ◽  
Exhaust Noise

This paper is devoted to the problems of modelling and calculation of propagation of low frequency sound in gas guides of power plants taking to account active sound sources. The structure of software for prediction and calculation of low-frequency sound propagation in gas guides have described. Software uses four-pole method and takes to account radiation from additional (active) sound course. By using software it is possible to estimate sound source parameters to provide efficient sound attenuation. Examples of software application to calculation of intake and exhaust noise of internal combustion engine are described. The results of calculations show the possibilities of four-pole method software using to design acoustically the parameters of gas guides and mufflers for the different fields of applications.

Integrated Anaerobic Digester and Fuel Cell Power Generation System for Community Use

2015 ◽  
Author(s):  
Ryan Falkenstein-Smith ◽  
Kang Wang ◽  
Ryan Milcarek ◽  
Jeongmin Ahn
Keyword(s):  
Fuel Cell ◽  
Waste Management ◽  
Power System ◽  
Internal Combustion Engine ◽  
Power Plants ◽  
Combustion Engine ◽  
Energy Content ◽  
New York State ◽  
Internal Combustion ◽  
Optimal Performance

New York State is expected to experience future population growth that is increasingly concentrated in urban areas, where there is already a heavy burden on the existing energy, water and waste management infrastructure. To meet aggressive environmental standards (such as that established by the State’s “80x50” goal), future electrical power capacity must produce substantially fewer greenhouse gas emissions than currently generated by coal- or natural gas-fired power plants. Currently, biogas is combusted to produce heat and electricity via an internal combustion engine generator set. A conventional internal combustion engine generator set is 22–45 % efficient in converting methane to electricity, thus wasting 65–78 % of the biogas energy content unless the lower temperature heat can be recovered. Fuel cells, on the other hand, are 40–60 % efficient in converting methane to electrical energy, and 80–90 % efficient for cogeneration if heat (> 400 °C) is recovered and utilized for heating and cooling in the community power system. This current research studies the feasibility of a community biomass-to-electricity power system which offers significant environmental, economic and resilience improvements over centrally-generated energy, with the additional benefit of reducing or eliminating disposal costs associated with landfills and publicly-owned treatment works (POTWs). Flame Fuel Cell (FFC) performance was investigated while modifying biogas content and fuel flow rate. A maximum power density peak at 748 mWcm-2 and an OCV of 0.856 V was achieved. It should be noted that the performance obtained with the model biofuel is comparable to the performances of direct methane fueled DC-SOFC and SC-SOFC. The common trends also concluded an acceptable range for optimal performance. Although the methane to CO2 ratios of 3:7 and 2:8 produced power, they are not the strongest ratios to have optimal performance, meaning that operation should stay between the 6:4/4:6 ratio range. Lastly, the amount of air added to the biogas mixture is crucial to achieving the optimal performance of the cell. The data obtained confirmed the feasibility of a biofuel driven fuel cell CHP device capable of achieving higher efficiency than existing technologies. The significant power output produced from the sustainable biogas composition is competitive with current hydrocarbon fuel sources. This idea can be expanded for a community waste management infrastructure.

Sign in / Sign up

Export Citation Format

Share Document