Effect of Heat Treatment on the Microstructure and Properties of Laser Cladding Alloy

Applied laser ◽  
2013 ◽  
Vol 33 (3) ◽  
pp. 233-238
Author(s):  
熊炜 Xiong Wei ◽  
张庆茂 Zhang Qingmao ◽  
夏琪 Xia Qi ◽  
郭亮 Guo Liang
Keyword(s):  
Heat Treatment ◽  
Laser Cladding ◽  
Microstructure And Properties

Effect of Heat Treatment on the Microstructure and Properties of Laser Cladding Alloy

Applied laser ◽  
2013 ◽  
Vol 33 (3) ◽  
pp. 233-238 ◽  
Author(s):  
熊炜 Xiong Wei ◽  
张庆茂 Zhang Qingmao ◽  
夏琪 Xia Qi ◽  
郭亮 Guo Liang
Keyword(s):  
Heat Treatment ◽  
Laser Cladding ◽  
Microstructure And Properties

scholarly journals Study on the Effect of Ni Addition on the Microstructure and Properties of NiTi Alloy Coating on AISI 316 L Prepared by Laser Cladding

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4373
Author(s):  
Yuqiang Feng ◽  
Zexu Du ◽  
Zhengfei Hu
Keyword(s):  
Laser Cladding ◽  
Niti Alloy ◽  
Second Phase ◽  
Content Increase ◽  
Strengthening Effect ◽  
Mixed Powder ◽  
Microstructure And Properties ◽  
Cladding Layer ◽  
Ni Addition ◽  
Aisi 316 L

This paper investigated 55 NiTi commercial alloy powder and 55 NiTi with 5% pure Ni mixed powder (55 NiTi + 5 Ni) coatings fabricated by laser cladding to study the effect of extra Ni addition on the microstructure and properties of the coating. The XRD and EDS results show that the major phases in the coatings were NiTi and Ni3Ti. Besides that, a second phase like Ni4Ti3, Fe2Ti, and NiTi2 was also detected, among which, NiTi2 was only found in 55 NiTi coating. The proportion of the phase composition in the coating was calculated via the software Image-Pro Plus. The hardness of the cladding layer reaches 770–830 HV, which was almost four times harder than the substrate, and the hardness of 55 NiTi + 5 Ni coating was around 8% higher than that of 55 NiTi coating. The wear resistance of the 55 NiTi + 5 Ni coating was also better; the wear mass loss decreased by about 13% and with a smaller friction coefficient compared with the 55 NiTi coating. These results are attributed to the solid solution strengthening effect caused by Ni addition and the second phase strengthening effect caused by the content increase of the Ni3Ti phase in the cladding layer.

Effect of Cooling Rate on Microstructure and Properties of Heat-Treated Fe3Al Intermetallics

2011 ◽  
Vol 189-193 ◽  
pp. 3891-3894
Author(s):  
Ya Min Li ◽  
Hong Jun Liu ◽  
Yuan Hao
Keyword(s):  
Heat Treatment ◽  
Cooling Rate ◽  
Lattice Distortion ◽  
Annealing Furnace ◽  
Microstructure And Properties ◽  
Homogenizing Annealing ◽  
Heat Treated ◽  
Mixed Fracture ◽  
Sand Mould ◽  
The Impact

The casting Fe3Al intermetallics were solidified in sodium silicate sand mould and permanent mould respectively to get different cooling rates. After heat treatment (1000°С/15 h homogenizing annealing + furnace cooling followed by 600°С/1 h tempering + oil quenching), the microstructure and properties of Fe3Al intermetallics were investigated. The results show that the heat-treated Fe3Al intermetallics at higher cooling rate has finer grained microstructure than lower cooling rate, and the lattice distortion increases due to the higher solid solubility of the elements Cr and B at higher cooling rate. The tensile strength and hardness of the Fe3Al intermetallics at higher cooling rate are slightly higher also. However, the impact power of intermetallics at higher cooling rate is 67.5% higher than that at lower cooling rate, and the impact fracture mode is also transformed from intercrystalline fracture at lower cooling rate to intercrystallin+transcrystalline mixed fracture at higher cooling rate.

Effect of Heat Treatment on Microstructure and Properties of Cu-3Ti-1Al Alloy

2013 ◽  
Vol 749 ◽  
pp. 282-286
Author(s):  
Xian Hui Wang ◽  
Xiao Chun Sun ◽  
Xiao Hong Yang ◽  
Shu Hua Liang
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Electrical Conductivity ◽  
Electron Microscope ◽  
Treatment Process ◽  
Intermetallic Phase ◽  
Strengthening Effect ◽  
Microstructure And Properties ◽  
Optimal Heat Treatment ◽  
Transmission Electron

The effect of heat treatment on the microstructure and properties of Cu-3Ti-1Al alloy was investigated. The microstructure was characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the hardness and electrical conductivity were tested as well. The results showed that the hardness and electrical conductivity of Cu-3Ti-1Al alloy increased significantly after solid solution and ageing treatment. The strengthening effect of Cu-3Ti-1Al alloy was attributed to the formation of intermetallic phase such as Ti3Al and fine precipitates of coherent β-Cu4Ti. With increase of the aging time and the temperature, the precipitates became coarse and incoherent with Cu matrix, and the discontinuous precipitate β started to grow from grain boundaries toward grain interior, which decreased hardness. As the formation of Ti3Al, β-Cu3Ti and β-Cu4Ti phase can efficiently reduce Ti concentration in Cu matrix. The electrical conductivity of Cu-3Ti-1Al alloy increases. In the range of experiments, the optimal heat treatment process for Cu-3Ti-1Al alloy is solid solution at 850°C for 4h and ageing 500°C for 2h, and the hardness and electrical conductivity are 227HV and 12.3%IACS, respectively.

Sign in / Sign up

Export Citation Format

Share Document