scholarly journals Pore structure and surface area of silica SBA-15: influence of washing and scale-up

2011 ◽  
Vol 2 ◽  
pp. 110-118 ◽  
Author(s):  
Jörg P Thielemann ◽  
Frank Girgsdies ◽  
Robert Schlögl ◽  
Christian Hess
Keyword(s):  
Pore Size Distribution ◽  
Surface Area ◽  
Pure Water ◽  
High Surface ◽  
Scale Up ◽  
High Surface Area ◽  
Batch Sizes ◽  
Ethanol Washing ◽  
Solvent Volume

The removal of the surfactant (EO20PO70EO20) by washing before final calcination is a critical step in the synthesis of silica SBA-15. In contrast to washing with pure water or ethanol, washing with water and ethanol may, depending on the quantity of solvent used, alter the homogeneity and order of the pores, but also lead to an increase of the surface area of SBA-15. A reduction of solvent volume and a controlled washing protocol allow the synthesis of high surface area SBA-15 materials with a narrow monomodal pore size distribution. For larger batch sizes the influence of the quantity of solvent on the quality of the SBA-15 is reduced.

scholarly journals Developing Eco-Friendly and Cost-Effective Porous Adsorbent for Carbon Dioxide Capture

Molecules ◽  
2021 ◽  
Vol 26 (7) ◽  
pp. 1962
Author(s):  
Mahboubeh Nabavinia ◽  
Baishali Kanjilal ◽  
Noahiro Fujinuma ◽  
Amos Mugweru ◽  
Iman Noshadi
Keyword(s):  
Carbon Dioxide ◽  
Surface Area ◽  
Co2 Capture ◽  
High Surface ◽  
Scale Up ◽  
Polymer Networks ◽  
High Surface Area ◽  
Excellent Thermal Stability ◽  
Doped Polymers ◽  
Metal Doped

To address the issue of global warming and climate change issues, recent research efforts have highlighted opportunities for capturing and electrochemically converting carbon dioxide (CO2). Despite metal doped polymers receiving widespread attention in this respect, the structures hitherto reported lack in ease of synthesis with scale up feasibility. In this study, a series of mesoporous metal-doped polymers (MRFs) with tunable metal functionality and hierarchical porosity were successfully synthesized using a one-step copolymerization of resorcinol and formaldehyde with Polyethyleneimine (PEI) under solvothermal conditions. The effect of PEI and metal doping concentrations were observed on physical properties and adsorption results. The results confirmed the role of PEI on the mesoporosity of the polymer networks and high surface area in addition to enhanced CO2 capture capacity. The resulting Cobalt doped material shows excellent thermal stability and promising CO2 capture performance, with equilibrium adsorption of 2.3 mmol CO2/g at 0 °C and 1 bar for at a surface area 675.62 m2/g. This mesoporous polymer, with its ease of synthesis is a promising candidate for promising for CO2 capture and possible subsequent electrochemical conversion.

scholarly journals Impact of Thermal Treatment of Nb2O5 on Its Performance in Glucose Dehydration to 5-Hydroxymethylfurfural in Water

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1685
Author(s):  
Katarzyna Morawa Eblagon ◽  
Anna Malaika ◽  
Karolina Ptaszynska ◽  
Manuel Fernando R. Pereira ◽  
José Luís Figueiredo
Keyword(s):  
Thermal Treatment ◽  
Surface Area ◽  
Pure Water ◽  
High Surface ◽  
High Surface Area ◽  
Acid Sites ◽  
High Ratio ◽  
Total Acidity ◽  
One Pot ◽  
Niobic Acid

The cascade dehydration of glucose to 5-hydroxymethylfurfural (HMF) was carried out in water over a series of Nb2O5 catalysts, which were derived from the thermal treatment of niobic acid at 300 and 550 °C, under air or inert atmosphere. Amorphous niobic acid showed high surface area (366 m2/g) and large acidity (2.35 mmol/g). With increasing the temperature of the thermal treatment up to 550 °C, the amorphous Nb2O5 was gradually transformed into a pseudohexagonal phase, resulting in a decrease in surface area (27–39 m2/g) and total acidity (0.05–0.19 mmol/g). The catalysts’ performance in cascade dehydration of glucose realized in pure water was strongly influenced by the total acidity of these materials. A remarkable yield of 37% HMF in one-pot reaction in water was achieved using mesoporous amorphous niobium oxide prepared by thermal treatment of niobic acid at 300 °C in air. The best-performing catalyst displayed a total acidity lower than niobic acid (1.69 mmol/g) which afforded a correct balance between a high glucose conversion and limited further conversion of the target product to numerous polymers and humins. On the other hand, the treatment of niobic acid at 550 °C, independently of the atmosphere used during the sample preparation (i.e., air or N2), resulted in Nb2O5 catalysts with a high ratio of Lewis to Brønsted acid sites and poor total acidity. These materials excelled at catalyzing the isomerization step in the tandem process.

Tenacious Mass Transfer Limitations Drive Catalytic Selectivity during Electrochemical Carbon Dioxide Reduction

2019 ◽  
Author(s):  
Kailun Yang ◽  
Recep Kas ◽  
Wilson A. Smith
Keyword(s):  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
Catalyst Layer ◽  
Active Surface ◽  
Active Surface Area ◽  
High Concentration ◽  
Copper Electrodes ◽  
Surface Enhanced ◽  
Local Current

<p>This study evaluated the performance of the commonly used strong buffer electrolytes, i.e. phosphate buffers, during CO<sub>2</sub> electroreduction in neutral pH conditions by using in-situ surface enhanced infrared absorption spectroscopy (SEIRAS). Unfortunately, the buffers break down a lot faster than anticipated which has serious implications on many studies in the literature such as selectivity and kinetic analysis of the electrocatalysts. Increasing electrolyte concentration, surprisingly, did not extend the potential window of the phosphate buffers due to dramatic increase in hydrogen evolution reaction. Even high concentration phosphate buffers (1 M) break down within the potentials (-1 V vs RHE) where hydrocarbons are formed on copper electrodes. We have extended the discussion to high surface area electrodes by evaluating electrodes composed of copper nanowires. We would like highlight that it is not possible to cope with high local current densities on these high surface area electrodes by using high buffer capacity solutions and the CO<sub>2</sub> electrocatalysts are needed to be evaluated by casting thin nanoparticle films onto inert substrates as commonly employed in fuel cell reactions and up to now scarcely employed in CO<sub>2</sub> electroreduction. In addition, we underscore that normalization of the electrocatalytic activity to the electrochemical active surface area is not the ultimate solution due to concentration gradient along the catalyst layer.This will “underestimate” the activity of high surface electrocatalyst and the degree of underestimation will depend on the thickness, porosity and morphology of the catalyst layer. </p> <p> </p>

Sign in / Sign up

Export Citation Format

Share Document