scholarly journals Influence of sunspaces on the heating demand in rooms – comparison of ISO 13790 calculation methods

2021 ◽  
Vol 20 (2) ◽  
pp. 069-082
Author(s):  
Magdalena Grudzińska
Keyword(s):  
Solar Radiation ◽  
Calculation Method ◽  
Energy Demand ◽  
Calculation Methods ◽  
Research Project ◽  
Solar Systems ◽  
Basic Assumptions ◽  
Radiation Distribution ◽  
Simplified Method ◽  
High Degree

The calculation method presented in ISO 13790 was developed during the research project PASSYS. It aimed to work out the way of estimating energy demand while taking into account different passive solar systems. The standard includes two calculation methods for sunspaces – a full and simplified method. They differ in terms of basic assumptions and the treatment of solar gains in the sunspace and conditioned rooms. There are some doubts about the interpretation of equations presented in the standard, especially when it comes to modelling the solar radiation distribution within the solar space. The paper presents a discussion on the basic hypotheses applied in full and simplified methods, together with the author’s suggestions regarding modifications to the ISO 13790 calculation methods. The modified methods allowed to satisfactorily predict the functioning of the exemplary sunspaces with a smaller area of glazed partitions and higher radiation absorptivity of the casing, that is spaces similar in terms of solar radiation utilisation to traditional living spaces. The phenomena typical for sunspaces with a high degree of glazing, such as the retransmission of reflected radiation, were not sufficiently taken into account in the calculation methods of the standard.

scholarly journals The use of simplified methods for designing according to EC6 and safety of masonry structures

2013 ◽  
Vol 12 (3) ◽  
pp. 013-020
Author(s):  
Wojciech Chruściel ◽  
Paweł Sulik
Keyword(s):  
Calculation Method ◽  
Masonry Walls ◽  
Masonry Structures ◽  
Calculation Methods ◽  
Simplified Method

The article describes the calculation method of masonry walls loaded vertically according to PN-EN 1996-1-1 and PN-EN 1996-3. The Calculation method is given and the differences between Eurocode 6 and "old Polish standard" are indicated. Additionally, the differences between calculations according to exact and simplified method described in Eurocode 6 that show adverse consequences of the use of simplified method. The places (formulas and assumptions), which causes the discrepancies in calculation methods are pointed out in the study.

scholarly journals Passive Solar Solutions for Buildings: Criteria and Guidelines for a Synergistic Design

2021 ◽  
Vol 11 (1) ◽  
pp. 376
Author(s):  
Giacomo Cillari ◽  
Fabio Fantozzi ◽  
Alessandro Franco
Keyword(s):  
Energy Demand ◽  
Theoretical Background ◽  
Environmental Benefits ◽  
Passive Systems ◽  
Extrinsic Factors ◽  
Solar Systems ◽  
Final Performance ◽  
Passive Solar ◽  
Energy Simulations

Passive solar system design is an essential asset in a zero-energy building perspective to reduce heating, cooling, lighting, and ventilation loads. The integration of passive systems in building leads to a reduction of plant operation with considerable environmental benefits. The design can be related to intrinsic and extrinsic factors that influence the final performance in a synergistic way. The aim of this paper is to provide a comprehensive view of the elements that influence passive solar systems by means of an analysis of the theoretical background and the synergistic design of various solutions available. The paper quantifies the potential impact of influencing factors on the final performance and then investigates a case study of an existing public building, analyzing the effects of the integration of different passive systems through energy simulations. General investigation has highlighted that latitude and orientation impact energy saving on average by 3–13 and 6–11 percentage points, respectively. The case study showed that almost 20% of the building energy demand can be saved by means of passive solar systems. A higher contribution is given by mixing direct and indirect solutions, as half of the heating and around 25% of the cooling energy demand can be cut off.

Innovative Volumetric Solar Receiver Micro-Design Based on Numerical Predictions

2015 ◽  
Author(s):  
Raffaele Capuano ◽  
Thomas Fend ◽  
Bernhard Hoffschmidt ◽  
Robert Pitz-Paal
Keyword(s):  
Solar Radiation ◽  
Energy Demand ◽  
Large Scale ◽  
Solar Power ◽  
Numerical Models ◽  
Numerical Predictions ◽  
Proper Design ◽  
Global Increase ◽  
Solar Power Tower ◽  
Solar Receiver

Due to the continuous global increase in energy demand, Concentrated Solar Power (CSP) represents an excellent alternative, or add-on to existing systems for the production of energy on a large scale. In some of these systems, the Solar Power Tower plants (SPT), the conversion of solar radiation into heat occurs in certain components defined as solar receivers, placed in correspondence of the focus of the reflected sunlight. In a particular type of solar receivers, defined as volumetric, the use of porous materials is foreseen. These receivers are characterized by a porous structure called absorber. The latter, hit by the reflected solar radiation, transfers the heat to the evolving fluid, generally air subject to natural convection. The proper design of these elements is essential in order to achieve high efficiencies, making such structures extremely beneficial for the overall performances of the energy production process. In the following study, a parametric analysis and an optimized characterization of the structure have been performed with the use of self-developed numerical models. The knowledge and results gained through this study have been used to define an optimization path in order to improve the absorber microstructure, starting from the current in-house state-of-the-art technology until obtaining a new advanced geometry.

scholarly journals Evaluating the Effect of External Horizontal Fixed Shading Devices’ Geometry on Internal Air Temperature, Daylighting and Energy Demand in Hot Dry Climate. Case Study of Ghardaïa, Algeria

Buildings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 348
Author(s):  
Sahar Magri Elouadjeri ◽  
Aicha Boussoualim ◽  
Hassan Ait Haddou
Keyword(s):  
Solar Radiation ◽  
Parametric Analysis ◽  
Energy Demand ◽  
Daylighting Simulation ◽  
Simulation Results ◽  
Shading Devices ◽  
Heating Loads ◽  
Shading Device ◽  
The City

The present study investigates the effect of fixed external shading devices’ geometry on thermal comfort, daylighting and energy demand for cooling and heating in the hot and dry climate of the city of Ghardaïa (Algeria). A parametric analysis was performed by using three software: RADIANCE 2.0 and DAYSIM 3.1 for daylighting simulation and TRNSYS.17 for thermal dynamic simulation. Three shading device parameters were assessed: the spacing between slats, the tilted angle and the slats installation. The vertical shading angle “VSA” is fixed; it is equal to the optimum shading angle measured for Ghardaïa. The simulation results indicate that fixed external shading devices have a significant impact on decreasing the energy demand for cooling; however, they are unable to reduce the total energy demand since they significantly increase heating loads. It was found that fixed external shading devices remove all risks associated with glare in summer by decreasing illuminance close to the window; however, they do not improve daylighting performance in winter because of glare. We note that even if the vertical shading angle “VSA” was the same for all cases, these did not present the same thermal and luminous behavior. This is mainly due to the amount and the way that the solar radiation penetrates space.

scholarly journals COMPARISON OF THREE CALCULATION METHODS OF ENERGY PERFORMANCE CERTIFICATES IN SLOVENIA

2018 ◽  
Vol 13 (1) ◽  
Author(s):  
Wadie Kidess
Keyword(s):  
Numerical Calculation ◽  
Energy Performance ◽  
Heat Losses ◽  
Calculation Methods ◽  
The Third ◽  
Simplified Method ◽  
Calculation Results ◽  
Thermal Bridges ◽  
Simplified Calculation ◽  
Family House

In order to get the authorization for issuing energy performance certificates in Slovenia, the expert candidate has to attend the prescribed course and pass the exam. The simplified method for heat losses calculation that is taught at this course neglects the thermal bridges, raising concerns whether the calculation results are reliable. In this paper we have compared three methods for calculation of thermal losses for a “typical” family house. The first is the above mentioned simplified calculation using a correctional factor; the second takes into account the thermal bridges, using linear thermal transmittances obtained by numerical calculation, and the third takes into account the thermal bridges, using default values for linear thermal transmittances. Noting that the second method returns the most exact values, we have found that the first method results are too large, yet still smaller than the third method results.

scholarly journals Passive solar systems for buildings: performance indicators analysis and guidelines for the design

2020 ◽  
Vol 197 ◽  
pp. 02008
Author(s):  
Giacomo Cillari ◽  
Fabio Fantozzi ◽  
Alessandro Franco
Keyword(s):  
Performance Indicators ◽  
Energy Demand ◽  
Evaluation Method ◽  
International Energy Agency ◽  
Objective Evaluation ◽  
Design Guidelines ◽  
Design Strategies ◽  
Energy Agency ◽  
Solar Systems ◽  
Passive Solar

Data from the International Energy Agency confirm that in a zero-energy perspective the integration of solar systems in buildings is essential. The development of passive solar strategies has suffered the lack of standard performance indicators and design guidelines. The aim of this paper is to provide a critical analysis of the main passive solar design strategies based on their classification, performance evaluation and selection methods, with a focus on integrability. Climate and latitude affect the amount of incident solar radiation and the heat losses, while integrability mainly depends on the building structure. For existing buildings, shading and direct systems represent the easiest and most effective passive strategies, while building orientation and shape are limited to new constructions: proper design can reduce building energy demand around 40%. Commercial buildings prefer direct use systems while massive ones with integrated heat storage are more suitable for family houses. A proper selection must consider the energy and economic balance of different building services involved: a multi-objective evaluation method represents the most valid tool to determine the overall performance of passive solar strategies.

Multilayer thin-film based nanophotonic windows: static versus electrotunable design

2021 ◽  
Author(s):  
Ashish Kumar Chowdhary ◽  
Debabrata Sikdar
Keyword(s):  
Solar Radiation ◽  
Energy Demand ◽  
Perfect Match ◽  
Motor Vehicles ◽  
Renewable Energy Resources ◽  
Large Area ◽  
Smart Windows ◽  
Experimental Realization ◽  
Voltage Range ◽  
Insulator Layers

Abstract To meet the global energy demand, rapid growth in fossil fuel consumption has significantly contributed to global warming. Judicious utilization of renewable energy resources could help to combat this global challenge. Here, we present a comparative study on the designs of static and electro-tunable ‘smart’ windows that could help to reduce the energy need of typical airconditioning systems deployed in buildings and motor vehicles. Our design comprises insulator–metal–insulator multi-layered thin-films deposited over a silica glass substrate to filter visible and infrared solar radiation selectively. For static windows, we optimize our design to operate in diverse climatic conditions by choosing different combinations and thicknesses of metal and insulator layers. Whereas for electro-tunable windows, we use an electro–optic polymer as the insulator layers to dynamically control portions of transmitted solar radiation over a voltage range of −12 V to +12 V. Through size-dependence analysis, we could safely assume that the performance of smart windows is less likely to degrade during experimental realization. Our designs are lithography-free, large-area compatible, polarization-independent, angle-insensitive, and robust to fabrication imperfections. The analytical results show a near-perfect match with the simulation findings. The theoretically calculated figure of merit indicates that our proposed smart windows can outperform industry-standard commercial windows.

Crack width calculation methods for large-scale concrete structures for the Ferry-Free E39

2018 ◽  
Author(s):  
Reignard Tan ◽  
Terje Kanstad ◽  
Mette R. Geiker ◽  
Max A. N. Hendriks
Keyword(s):  
Cross Sections ◽  
Calculation Method ◽  
Crack Width ◽  
Large Scale ◽  
Concrete Structures ◽  
Calculation Methods ◽  
Empirical Formulas ◽  
Eurocode 2 ◽  
Semi Empirical

<p>Motivated by the establishment of a Ferry-Free E39 coastal highway route, crack width calculation methods for design of large-scale concrete structures are discussed. It is argued that the current semi-empirical formulas recommended by Eurocode 2 is inconsistent and overly conservative for cross sections with large bar diameters and covers. A suggestion to formulating a more consistent crack width calculation method is given.</p>

Sign in / Sign up

Export Citation Format

Share Document