Carbon and low alloy cast steels for general applications

2021 ◽  
Keyword(s):  
Cast Steels ◽  
Alloy Cast

scholarly journals The Structure of the Silumin Coat on Alloy Cast Steels

2012 ◽  
Vol 12 (2) ◽  
pp. 215-220
Author(s):  
T. Szymczak
Keyword(s):  
Phase Structure ◽  
High Speed ◽  
Cast Steel ◽  
Intermetallic Phases ◽  
External Layer ◽  
Cast Steels ◽  
Steel Grades ◽  
The Absolute ◽  
The Given ◽  
Alloy Cast

The Structure of the Silumin Coat on Alloy Cast Steels The work presents the analysis results of the structure of the coat obtained by dipping in silumin AlSi5 of two grades of alloy cast steel: GX6CrNiTi18-10 (LH18N9T) and GX39Cr13 (LH14). The temperature of the silumin bath was 750±5°C, and the hold-up time of the cast steel element τ = 180 s. The absolute thickness of the coat obtained in the given conditions was g = 104 μm on cast steel GX6CrNiTi18-10 and g = 132 μm on GX39Cr13. The obtained coat consisted of three layers of different phase structure. The first layer from the base "g1" was constructed of the phase AlFe including Si and alloy additives of the tested cast steel grades: Cr and Ni (GX6CrNiTi18-10) and Cr (GX39Cr13). The second layer "g1" of intermetallic phases AlFe which also contains Si and Cr crystallizes on it. The last, external layer "g2" of the coat consists of the silumin containing the intermetallic phases AlFeSi which additionally can contain alloy additives of the cast steel. It was shown that there were no carbides on the coat of the tested cast steels which are the component of their microstructure, as it took place in the case of the coat on the high speed steels.

Constant-Amplitude Fatigue Behavior of Five Carbon or Low-Alloy Cast Steels at Room Temperature and −45°C

2008 ◽  
pp. 140-140-21 ◽  
Author(s):  
RI Stephens ◽  
JH Chung ◽  
SG Lee ◽  
HW Lee ◽  
A Fatemi ◽  
...  
Keyword(s):  
Room Temperature ◽  
Fatigue Behavior ◽  
Constant Amplitude ◽  
Cast Steels ◽  
Alloy Cast

Experimental Studies on Abrasive Wear of Surface-Hardened and Shot Peened Alloy Cast Steels

2016 ◽  
Vol 674 ◽  
pp. 201-206
Author(s):  
Andrzej Norbert Wieczorek
Keyword(s):  
Abrasive Wear ◽  
Cast Steel ◽  
Experimental Studies ◽  
Operating Conditions ◽  
Linear Wear ◽  
Plastic Properties ◽  
Cast Steels ◽  
Wear Tests ◽  
Alloy Cast

The paper presents the results of wear tests of shot-peened and non-shot-peened cast steels with the use of an especially designed test rig simulating real operating conditions of chain wheels. The chain wheels subjected to tests were operated with the use of loose quartz abrasive. The studies involved the determination of strength and plastic properties, hardness distributions, microstructure and linear wear of the selected cast steels. Based on the results obtained, the following was found: the abrasive wear of cast steel chain wheels increased after shot peening.

scholarly journals Comparative Studies on the Wear of ADI Alloy Cast Irons as Well as Selected Steels and Surface-Hardened Alloy Cast Steels in the Presence of Abrasive

2017 ◽  
Vol 62 (1) ◽  
pp. 119-128 ◽  
Author(s):  
A. N. Wieczorek
Keyword(s):  
Operating Conditions ◽  
Linear Wear ◽  
Wear Properties ◽  
Cast Irons ◽  
Hardened Alloy ◽  
Cast Steels ◽  
Structural Applications ◽  
Alloy Steels ◽  
Wear Tests ◽  
Alloy Cast

AbstractThe paper presents the results of wear tests obtained for 4 groups of materials: surface-hardened alloy steels and alloy cast steels for structural applications, hard-wearing surface-hardened alloy cast steels, and austempered alloy cast irons. The wear tests have been performed on a specially designed test rig that allows reproducing the real operating conditions of chain wheels, including the rolling and sliding form of contact between elements. The chain wheels subjected to tests were operated with the use of loose quartz abrasive. This study presents results of measurements of material parameters, micro-structure of a surface subject to wear, as well as the linear wear determined for the materials considered. Based on the results, the following was found: the best wear properties were obtained for surface-hardened alloy steels and wear surface; strengthening of the ADI surface took place - most probably as a result of transformation of austenite into martensite; the uniformity of the structure of the materials affects the surface wear process. The study also indicated a significant degree of graphite deformation in ADI characterized by the upper ausferritic structure and its oblique orientation in relation to the surface, which resulted in a facilitated degradation of the surface caused by the quartz abrasive.

ChemInform Abstract: Alloy Cast Steels with Nitrogen

ChemInform ◽  
2010 ◽  
Vol 28 (30) ◽  
pp. no-no
Author(s):  
J.-M. MASSON
Keyword(s):  
Cast Steels ◽  
Alloy Cast
Sign in / Sign up

Export Citation Format

Share Document