Specification for cellulose acetate sheet for spectacle frames

1959 ◽  
Keyword(s):  
Cellulose Acetate

Cellulose Acetate Reverse Osmosis Membrane Structure

1972 ◽  
Vol 30 ◽  
pp. 528-529
Author(s):  
H. K. Plummer ◽  
E. Eichen ◽  
C. D. Melvin
Keyword(s):  
Cellulose Acetate ◽  
Reverse Osmosis ◽  
Membrane Structure ◽  
Freeze Drying ◽  
Dense Layer ◽  
Water Removal ◽  
Reverse Osmosis Membrane ◽  
Correct Interpretation ◽  
Electron Image ◽  
Scanning Electron

Much of the work reported in the literature on cellulose acetate reverse osmosis membranes has raised new and important questions with regard to the dense or “active” layer of these membranes. Several thickness values and structures have been attributed to the dense layer. To ensure the correct interpretation of the cellulose acetate structure thirteen different preparative techniques have been used in this investigation. These thirteen methods included various combinations of water substitution, freeze drying, freeze sectioning, fracturing, embedding, and microtomy techniques with both transmission and scanning electron microscope observations.It was observed that several factors can cause a distortion of the structure during sample preparation. The most obvious problem of water removal can cause swelling, shrinking, and folds. Improper removal of embedding materials, when used, can cause a loss of electron image contrast and, or structure which could hinder interpretation.

The Control of Cigarette Smoke Deliveries Using Heat-Shrinkable Films

1975 ◽  
Vol 8 (2) ◽  
Author(s):  
R. A. Crellin ◽  
G. O. Brooks ◽  
H. G. Horsewell
Keyword(s):  
Particulate Matter ◽  
Cellulose Acetate ◽  
Cigarette Smoke ◽  
Total Particulate Matter ◽  
Puff Volume ◽  
Cigarette Paper ◽  
High Degree

AbstractA ventilating filter for cigarettes has been developed which reduces the delivery of smoke constituents from the final two to three puffs. Since the normaI delivery for these three puffs can account for up to half the total particulate matter and nicotine delivered by the whole cigarette, usefuI reductions per cigarette can be produced. The ventilating filter consists of cellulose acetate tow wrapped in heat-shrinkable film and attached to a tobacco rod using perforated tipping paper. When the cigarette is smoked, the perforations remain closed by contact with the impermeable film until transfer of heat to the filter is sufficient to soften the filter tow and shrink the film. Ventilating air now enters the cigarette and reduces the smoke deliveries. The effectiveness of the ventilating filter is increased by using films which have a low shrink temperature, high shrink tension and a high degree of biaxiaI shrinkage. Increases in filter plasticiser level, tipping perforation area and puff volume improve the effectiveness of the ventilating filter but increases in cigarette paper porosity and tobacco butt length reduce the effectiveness

Characteristics and Potential Applications of Cellulose Acetate

2014 ◽  
Vol 68 (9) ◽  
pp. 1018-1024
Author(s):  
Shu Shimamoto ◽  
Shizuka Okada ◽  
Toshikazu Nakamura
Keyword(s):  
Cellulose Acetate ◽  
Potential Applications

Development of Sustained Release Multi-Component Microparticulate System of Diclofenac Sodium and Tizanidine Hydrochloride

1970 ◽  
Vol 1 (1) ◽  
pp. 97-105
Author(s):  
Kamlesh Dashora ◽  
Shailendra Saraf ◽  
Swarnalata Saraf
Keyword(s):  
Particle Size ◽  
Sustained Release ◽  
Cellulose Acetate ◽  
Rate Constant ◽  
Diclofenac Sodium ◽  
Order Rate Constant ◽  
Anomalous Transport ◽  
First Order ◽  
Sem Study ◽  
Transport Type

Sustained released tablets of diclofenac sodium (DIC) and tizanidine hydrochloride (TIZ) were prepared by using different proportions of cellulose acetate (CA) as the retardant material. Nine formulations of tablets having different proportion of microparticles developed by varied proportions of polymer: drug ratio ‘’i.e.’’; 1:9 -1:3 for DIC and 1:1 – 3:1 for TIZ. Each tablet contained equivalent to 100 mg of DIC and 6mg of TIZ. The prepared microparticles were white, free flowing and spherical in shape (SEM study), with  the particle size varying from 78.8±1.94 to 103.33±1.28 µm and 175.92± 9.82 to 194.94±14.28µm for DIC  and TIZ, respectively.  The first order rate constant K1 of formulations were found to be in the range of  K1 = 0.117-0.272 and 0.083- 0.189 %hr-1for DIC and TIZ, respectively. The value of exponent coefficient (n) was found to be in the range of 0.6328-0.9412  and 0.8589-1.1954 for DIC and TIZ respectively indicates anomalous  to  non anomalous transport type of diffusions among different formulations

Sign in / Sign up

Export Citation Format

Share Document