Flat bottom railway rails

1926 ◽  
Keyword(s):  
Flat Bottom

UJI TARIK HIDRODINAMIKMODEL KAPAL BERSAYAP WiSE DENGAN LAMBUNG DASAR BERSTEP

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Iskendar Iskendar ◽  
Andi Jamaludin ◽  
Paulus Indiyono
Keyword(s):  
Comparative Study ◽  
Model Test ◽  
Hydrodynamic Model ◽  
Surface Effect ◽  
Center Of Gravity ◽  
Test Results ◽  
Flat Bottom ◽  
Towing Tank ◽  
Test Models ◽  
Wetted Surface Area

This paper describes hydrodynamic model tests of Wing in Surface Effect (WiSE) Craft. These craft  was fitted with  stephull  form in different location on longitudinal flat bottom (stepedhull planning craft) to determine the influences of sticking and porpoising motion performances. These motions are usually occured when the craft start to take-off from water surfaces. The test models with scale of 1 : 7 were comprised of 4 (four) stephull models and 1 (one) non-stephull model  as a comparative study. The hydrodynamic  tests were performed with craft speed of 16 – 32 knots (prototype values) in Towing Tank at UPT. Balai Pengkajian dan Penelitian Hidrodinamika (BPPH), BPPT, Surabaya. The resistance (drag) was measured by dynamo meter and the trim of model (draft changing at fore and aft  of model due to model speed) was measured by trim meter. By knowing the value of model trim, the wetted surface area can be determined. Then, the lift forces were calculated based on these measured values. The model test results were presented on tables and curves.  Test results show that models  with step located far away from center of gravity of the WiSE craft tend to porpoising and sticking condition, except if the step location on the below of these center of gravity. While model without step tends to sticking conditions.

Simple explicit model of liquid mean flow in region above axial impeller

1985 ◽  
Vol 50 (11) ◽  
pp. 2396-2410
Author(s):  
Miloslav Hošťálek ◽  
Ivan Fořt
Keyword(s):  
Vortex Flow ◽  
Flow Model ◽  
Quantitative Agreement ◽  
Mean Flow ◽  
Flat Bottom ◽  
Proposed Model ◽  
Minimum Number ◽  
The Mean ◽  
Model Equations ◽  
Radial Circulation

The study describes a method of modelling axial-radial circulation in a tank with an axial impeller and radial baffles. The proposed model is based on the analytical solution of the equation for vortex transport in the mean flow of turbulent liquid. The obtained vortex flow model is tested by the results of experiments carried out in a tank of diameter 1 m and with the bottom in the shape of truncated cone as well as by the data published for the vessel of diameter 0.29 m with flat bottom. Though the model equations are expressed in a simple form, good qualitative and even quantitative agreement of the model with reality is stated. Apart from its simplicity, the model has other advantages: minimum number of experimental data necessary for the completion of boundary conditions and integral nature of these data.

scholarly journals A Well-Balanced SPH-ALE Scheme for Shallow Water Applications

2021 ◽  
Vol 88 (3) ◽  
Author(s):  
Alberto Prieto-Arranz ◽  
Luis Ramírez ◽  
Iván Couceiro ◽  
Ignasi Colominas ◽  
Xesús Nogueira
Keyword(s):  
Shallow Water ◽  
Source Term ◽  
Arbitrary Lagrangian Eulerian ◽  
Flat Bottom ◽  
Riemann Solvers ◽  
Eulerian Formulation ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Numerical Fluxes ◽  
And Behavior

AbstractIn this work, a new discretization of the source term of the shallow water equations with non-flat bottom geometry is proposed to obtain a well-balanced scheme. A Smoothed Particle Hydrodynamics Arbitrary Lagrangian-Eulerian formulation based on Riemann solvers is presented to solve the SWE. Moving-Least Squares approximations are used to compute high-order reconstructions of the numerical fluxes and, stability is achieved using the a posteriori MOOD paradigm. Several benchmark 1D and 2D numerical problems are considered to test and validate the properties and behavior of the presented schemes.

Sign in / Sign up

Export Citation Format

Share Document