Thermal spraying. Determination of tensile adhesive strength

2017 ◽  
Keyword(s):  
Adhesive Strength ◽  
Thermal Spraying

Interfacial Characteristics and Determination of Cohesive and Adhesive Strength of Plasma-Coated Hydroxyapatite via Nanoindentation and Microscratch Techniques

Langmuir ◽  
2014 ◽  
Vol 30 (38) ◽  
pp. 11412-11420 ◽  
Author(s):  
Colm McManamon ◽  
Johann P. de Silva ◽  
John Power ◽  
Sonia Ramirez-Garcia ◽  
Michael A. Morris ◽  
...  
Keyword(s):  
Adhesive Strength ◽  
Interfacial Characteristics

Tribological performance of AlCrN–MoS2/PTFE hard-lubricant composite coatings

2019 ◽  
Vol 234 (9) ◽  
pp. 1355-1367
Author(s):  
Yang Lu ◽  
Jianxin Deng ◽  
Wenlong Song ◽  
Xuemu Li ◽  
Liangliang Zhang ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Molybdenum Disulfide ◽  
Tribological Properties ◽  
Adhesive Strength ◽  
Wear Track ◽  
Composite Coatings ◽  
Thermal Spraying ◽  
Tribological Performance ◽  
Ptfe Composite ◽  
Spraying Method

In order to improve the tribological performance of the physical vapor-deposited AlCrN coatings, molybdenum disulfide (MoS2)/poly tetra fluoroethylene (PTFE) coatings were fabricated on the AlCrN coatings surface through the thermal spraying method. The microstructure, adhesive strength, hardness, and tribological properties were investigated. Reciprocating sliding tests against SiC ball were executed with a ball-on-plate tribometer. Results showed that the adhesive strength between the AlCrN–MoS2/PTFE composite coatings and substrate was increased by about 15% compared with single AlCrN coatings. Compared with the single MoS2/PTFE coatings, the hardness of the AlCrN–MoS2/PTFE composite coatings surface was increased by about 15%. The MoS2/PTFE layer can availably reduce the friction coefficient of single AlCrN layer, and the AlCrN–MoS2/PTFE composite coatings exhibited the lowest and the most stable friction coefficient. In addition, the MoS2/PTFE layer existed on the wear track and accumulated on both the sides, which was the main reason that the friction coefficient was still lower compared with the samples without MoS2/PTFE coatings.

Determination of epoxy coating wet-adhesive strength using a standardized ASTM/ISO scratch test

2010 ◽  
Vol 8 (2) ◽  
pp. 255-263 ◽  
Author(s):  
Han Jiang ◽  
Robert Browning ◽  
Peng Liu ◽  
T. A. Chang ◽  
Hung-Jue Sue
Keyword(s):  
Adhesive Strength ◽  
Scratch Test ◽  
Epoxy Coating

scholarly journals ASSESSMENT TRIBOLOGICAL PROPERTIES OF COATINGS APPLIED BY HVOF TECHNOLOGY

2013 ◽  
Vol 7 (3) ◽  
pp. 135-139 ◽  
Author(s):  
Janette Brezinová ◽  
Anna Guzanová ◽  
Dagmar Draganovská ◽  
Marián Egri
Keyword(s):  
Room Temperature ◽  
Adhesive Wear ◽  
Thermal Spraying ◽  
Basic Material ◽  
High Velocity Oxygen Fuel ◽  
Properties Of Coatings ◽  
Oxygen Fuel ◽  
Spraying Method

Abstract In this article, the attention is paid to the HVOF (High Velocity Oxygen Fuel) thermal spraying method by which the progressive coatings are applied on basic material C15E (STN 412020). These coatings are based on C-17CO, WC-CO-Cr and Cr3C2-25NiCr. There was made determination of the chemical composition of the coatings and assessment of coatings quality - adhesion, microhardness, porosity and wear resistance at room temperature (21°C) and also at operational elevated temperature (900°C). Results of adhesive wear showed high quality of all evaluated coatings and their suitability to extreme tribological conditions.

Sign in / Sign up

Export Citation Format

Share Document