Method of measurement of centre beam intensity and beam angle(s) of reflector lamps

2010 ◽  
Keyword(s):  
Beam Intensity ◽  
Beam Angle ◽  
Method Of Measurement

Systematic Reflections and the Two Beam Concept of Extinction Distance

1967 ◽  
Vol 25 ◽  
pp. 332-333
Author(s):  
S. S. Sheinin ◽  
C. D. Cann
Keyword(s):  
Dynamical Theory ◽  
Beam Intensity

The effects of systematic reflections on the variation of diffracted beam intensity with depth in a crystal can only be taken into account by using the multi-beam dynamical theory. The results of calculations of this kind, which are presented here, indicate that the intensity profiles obtained are not periodic. Since extinction distance is a concept strictly applicable only when the diffracted beam intensity varies periodically with depth, its use as a parameter in describing multi-beam intensity profiles must be carefully considered.

Lorentz electron microscopy of magnetic domains in rapidly solidified and annealed Pt-Co-B alloys

1991 ◽  
Vol 49 ◽  
pp. 784-785
Author(s):  
N. Qiu ◽  
J. E. Wittig
Keyword(s):  
Rapid Solidification ◽  
Ion Beam ◽  
Magnetic Behavior ◽  
High Coercivity ◽  
Magnetic Domains ◽  
Beam Angle ◽  
Tem Analysis ◽  
Intrinsic Coercivity ◽  
Hard Magnets ◽  
Rapidly Solidified

PtCo hard magnets have specialized applications owing to their relatively high coercivity combined with corrosion resistance and ductility. Increased intrinsic coercivity has been recently obtained by rapid solidification processing of PtCo alloys containing boron. After rapid solidification by double anvil splat quenching and subsequent annealing for 30 minutes at 650°C, an alloy with composition Pt42Co45B13 (at.%) exhibited intrinsic coercivity up to 14kOe. This represents a significant improvement compared to the average coercivities in conventional binary PtCo alloys of 5 to 8 kOe.Rapidly solidified specimens of Pt42Co45B13 (at.%) were annealed at 650°C and 800°C for 30 minutes. The magnetic behavior was characterized by measuring the coercive force (Hc). Samples for TEM analysis were mechanically thinned to 100 μm, dimpled to about 30 nm, and ion milled to electron transparency in a Gatan Duomill at 5 kV and 1 mA gun current. The incident ion beam angle was set at 15° and the samples were liquid nitrogen cooled during milling. These samples were analyzed with a Philips CM20T TEM/STEM operated at 200 kV.

Divergent beam microanalysis studies of bimetallic platinum catalysts supported on γ-AL2O3

1995 ◽  
Vol 53 ◽  
pp. 428-429
Author(s):  
JR Fryer ◽  
Z Huang ◽  
D Stirling ◽  
G. Webb
Keyword(s):  
Dead Time ◽  
Platinum Catalysts ◽  
Beam Intensity ◽  
Beam Diameter ◽  
Divergent Beam ◽  
Bimetallic Systems ◽  
Reforming Catalyst ◽  
Before And After ◽  
Individual Particles

Platinum dispersed on γ-alumina is used as a reforming catalyst to convert linear hydrocarbons to cyclic aromatic products. To improve selectivity and lifetime of the catalyst, other elements are included, and we have studied the distributions of Pt/Re, and Pt/Sn, bimetallic systems on the support both before and after use in octane reforming. Often, one or both of the components are not resolvable by HREM or microanalysis as individual particles because of small size and lack of contrast on the alumina, and divergent beam microanalysis has been used to establish the presence and relationship between the two elements.In the majority of catalysts the platinum is in the form of small panicles, some of which are large enough to be resolvable in the microscope. The ABT002B microscope with Link windowless Pentafet detector, used in this work, was able to obtain a resolvable signal from particles of 2nm diameter upwards. When the beam was concentrated on to such a particle the signal was at a maximum, and as the beam diameter was diverged - at the same total beam intensity and dead time - the signal decreased as shown in Figure 1.

LENS CLASSIFICATION ACCORDING TO THE TYPE OF LIGHT SPOT USING A NEURAL NETWORK

2020 ◽  
Vol 2020 (4) ◽  
pp. 4-14
Author(s):  
Vladimir Budak ◽  
Ekaterina Ilyina
Keyword(s):  
Neural Network ◽  
Light Intensity ◽  
Convolutional Neural Network ◽  
Deep Convolutional Neural Network ◽  
Beam Angle ◽  
New Model ◽  
Technical Parameters ◽  
Transfer Training ◽  
Trained Network

The article proposes the classification of lenses with different symmetrical beam angles and offers a scale as a spot-light’s palette. A collection of spotlight’s images was created and classified according to the proposed scale. The analysis of 788 pcs of existing lenses and reflectors with different LEDs and COBs carried out, and the dependence of the axial light intensity from beam angle was obtained. A transfer training of new deep convolutional neural network (CNN) based on the pre-trained GoogleNet was performed using this collection. GradCAM analysis showed that the trained network correctly identifies the features of objects. This work allows us to classify arbitrary spotlights with an accuracy of about 80 %. Thus, light designer can determine the class of spotlight and corresponding type of lens with its technical parameters using this new model based on CCN.

Sign in / Sign up

Export Citation Format

Share Document