Classification and application of cutting materials for metal removal with defined cutting edges. Designation of the main groups and groups of application

2004 ◽  
Keyword(s):  
Metal Removal

Performance Analysis on Eco-friendly Machining of Ti6Al4V using Powder Mixed with Different Dielectrics in WEDM

2020 ◽  
Vol 17 (3) ◽  
pp. 8128-8139
Author(s):  
S. Chakraborty ◽  
S. Mitra ◽  
D. Bose
Keyword(s):  
Metal Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Process Efficiency ◽  
Machining Parameters ◽  
Dielectric Fluids ◽  
High Emission ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The recent scenario of modern manufacturing is tremendously improved in the sense of precision machining and abstaining from environmental pollution and hazard issues. In the present work, Ti6Al4V is machined through wire EDM (WEDM) process with powder mixed dielectric and analyzed the influence of input parameters and inherent hazard issues. WEDM has different parameters such as peak current, pulse on time, pulse off time, gap voltage, wire speed, wire tension and so on, as well as dielectrics with powder mixed. These are playing an essential role in WEDM performances to improve the process efficiency by developing the surface texture, microhardness, and metal removal rate. Even though the parameter’s influencing, the study of environmental effect in the WEDM process is very essential during the machining process due to the high emission of toxic vapour by the high discharge energy. In the present study, three different dielectric fluids were used, including deionised water, kerosene, and surfactant added deionised water and analysed the data by taking one factor at a time (OFAT) approach. From this study, it is established that dielectric types and powder significantly improve performances with proper set of machining parameters and find out the risk factor associated with the PMWEDM process.

Application of Natural Absorbents for Metal Removal From Waste Water

2012 ◽  
Vol 3 (4) ◽  
pp. 110-111
Author(s):  
B. Mahesh B. Mahesh ◽  
◽  
V. Hema Sailaja ◽  
B. Vijay Kumar ◽  
K. Veera Babu ◽  
...  
Keyword(s):  
Waste Water ◽  
Metal Removal

Treatment of a complex landfill leachate with peat

1978 ◽  
Vol 5 (1) ◽  
pp. 83-97 ◽  
Author(s):  
Robert D. Cameron
Keyword(s):  
Chemical Oxygen Demand ◽  
Ferric Chloride ◽  
Landfill Leachate ◽  
Metal Removal ◽  
Oxygen Demand ◽  
Treatment Method ◽  
Manganese Concentration ◽  
Chemical Pretreatment ◽  
Iron Manganese

The use of cheap, locally available peat as a treatment method for landfill leachate was investigated by passing leachate through plexiglass columns filled with an amorphous-granular peat. Preliminary adjustment of pH showed that reducing pH to 4.8 dramatically reduced adsorption. Increasing the pH to 8.4, metal removal was increased owing to filtration of precipitated metals. The best adsorption of metals occurred at the 'natural' pH of 7.1. Manganese was found to be the limiting pollutant. At the 0.05 mg/ℓ maximum acceptable manganese concentration 94% of the total metals were removed, requiring 159 kg of peat per 1000 ℓ of leachate.Resting the peat for 1 month did significantly increase removal capacity.Desorption of some contaminants occurred when water was percolated through the peat. The desorption test effluent was not toxic to fish although iron, lead and COD (chemical oxygen demand) exceeded acceptable values.Chemical pretreatment using lime and ferric chloride achieved significant iron, manganese and calcium removals. Chemical pretreatment followed by peat adsorption offered no advantage other than reducing toxicity to fish.Peat treatment alone was effective in reducing concentrations to a level that was non-toxic to fish.

Sign in / Sign up

Export Citation Format

Share Document