Copper and copper alloys. Estimation of average grain size

2015 ◽  
Keyword(s):  
Grain Size ◽  
Copper Alloys ◽  
Average Grain Size

scholarly journals Crystallography of grain refinement in cast zinc–copper alloys

2015 ◽  
Vol 48 (3) ◽  
pp. 890-900 ◽  
Author(s):  
Zhilin Liu ◽  
Dong Qiu ◽  
Feng Wang ◽  
John A. Taylor ◽  
Mingxing Zhang
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Copper Alloys ◽  
Diffraction Method ◽  
Electron Backscattered Diffraction ◽  
Grain Coarsening ◽  
Cu Content ◽  
Edge Matching ◽  
Average Grain Size ◽  
Cast Alloys

Adding the peritectic forming element Cu effectively reduced the average grain size of cast Zn by over 85%. At a specified cast condition, the smallest grain size was obtained at 2 wt% Cu addition. A further increase in Cu content led to grain coarsening in the cast Zn–Cu alloys. Although the solute effect of Cu was predominately responsible for the grain refinement through restriction of the grain growth, it was found that the variation of grain size is also closely related to the formation of the pro-peritectic phase, ∊-CuZn4. Crystallographic calculations using the edge-to-edge matching model showed low interatomic misfit and interplanar mismatch between Zn and the ∊-CuZn4phase. In addition, a reproducible h.c.p.–h.c.p. (h.c.p. denotes hexagonal close-packed) orientation relationship between Zn and the ∊-CuZn4particles (located within the Zn grain centres) was also experimentally determined using the electron backscattered diffraction method. This indicated the high potency of the pro-peritectic ∊-CuZn4particles as effective heterogeneous nucleation sites for η-Zn, which further refined the Zn grains. However, when the Cu content was over 2.0 wt%, formation of large ∊-CuZn4particles resulted in grain coarsening of the cast alloys.

Grain Refinement of Copper Alloys by Equal Channel Angular Pressing

2004 ◽  
Vol 449-452 ◽  
pp. 177-180 ◽  
Author(s):  
Cha Yong Lim ◽  
Jae Hyuck Jung ◽  
Seung Zeon Han
Keyword(s):  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Copper Alloys ◽  
Metallic Materials ◽  
Fine Grained ◽  
Angular Pressing ◽  
Fine Grain ◽  
Transmission Electron ◽  
Ultrafine Grained ◽  
Average Grain Size

The equal channel angular pressing (ECAP) is one of the methods to refine the grain size of metallic materials. This study investigates the effect of ECAP process on the formation of the fine grain size in oxygen free Cu and Cu alloys. The average grain size has been refined from 150 µm before ECAP to 300 nm. Microstructure was analyzed by transmission electron micrography (TEM). The diffraction pattern of the selected area confirmed the formation of ultrafine-grained structure with high angle grain boundaries after 8 cycles of ECAP. Mechanical properties such as microhardness and tensile properties of the ultra-fine grained copper materials have been investigated.

Surface Modification and its Influence on the Microstructure and Creep Resistance of Nickel Based Superalloy René 77 / Modyfikacja Powierzchniowa Oraz Jej Wpływ Na Mikrostrukture I Wytrzymałosc Na Pełzanie Odlewów Z Nadstopu Niklu Ren´E 77

2013 ◽  
Vol 58 (1) ◽  
pp. 95-98 ◽  
Author(s):  
M. Zielinska ◽  
J. Sieniawski
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Surface Modification ◽  
Turbine Blades ◽  
Processing Parameters ◽  
Grain Structure ◽  
Creep Tests ◽  
Cobalt Aluminate ◽  
Nickel Based Superalloy ◽  
Average Grain Size

Superalloy René 77 is very wide used for turbine blades, turbine disks of aircraft engines which work up to 1050°C. These elements are generally produced by the investment casting method. Turbine blades produced by conventional precision casting methods have coarse and inhomogeneous grain structure. Such a material often does not fulfil basic requirements, which concern mechanical properties for the stuff used in aeronautical engineering. The incorporation of controlled grain size improved mechanical properties. This control of grain size in the casting operation was accomplished by the control of processing parameters such as casting temperature, mould preheating temperature, and the use of grain nucleates in the face of the mould. For nickel and cobalt based superalloys, it was found that cobalt aluminate (CoAl2O4) has the best nucleating effect. The objective of this work was to determine the influence of the inoculant’s content (cobalt aluminate) in the surface layer of the ceramic mould on the microstructure and mechanical properties at high temperature of nickel based superalloy René 77. For this purpose, the ceramic moulds were made with different concentration of cobalt aluminate in the primary slurry was from 0 to 10% mass. in zirconium flour. Stepped and cylindrical samples were casted for microstructure and mechanical examinations. The average grain size of the matrix ( phase), was determined on the stepped samples. The influence of surface modification on the grain size of up to section thickness was considered. The microstructure investigations with the use of light microscopy and scanning electron microscopy (SEM) enable to examine the influence of the surface modification on the morphology of ’ phase and carbides precipitations. Verification of the influence of CoAl2O4 on the mechanical properties of castings were investigated on the basis of results obtained form creep tests.

Sign in / Sign up

Export Citation Format

Share Document