Dimensions for air pressure brake chamber

1967 ◽  
Keyword(s):  
Air Pressure

Signal Interpretation Considerations When Estimating Subglottal Pressure From Oral Air Pressure

2019 ◽  
Vol 62 (5) ◽  
pp. 1326-1337 ◽  
Author(s):  
Brittany L. Perrine ◽  
Ronald C. Scherer ◽  
Jason A. Whitfield
Keyword(s):  
Standard Condition ◽  
Word Production ◽  
Air Pressure ◽  
Pressure Waveform ◽  
Pressure Measurements ◽  
Air Leak ◽  
Pressure Signal ◽  
Adult Participants ◽  
Syllable Repetition ◽  
Subglottal Pressure

Purpose Oral air pressure measurements during lip occlusion for /pVpV/ syllable strings are used to estimate subglottal pressure during the vowel. Accuracy of this method relies on smoothly produced syllable repetitions. The purpose of this study was to investigate the oral air pressure waveform during the /p/ lip occlusions and propose physiological explanations for nonflat shapes. Method Ten adult participants were trained to produce the “standard condition” and were instructed to produce nonstandard tasks. Results from 8 participants are included. The standard condition required participants to produce /pːiːpːiː.../ syllables smoothly at approximately 1.5 syllables/s. The nonstandard tasks included an air leak between the lips, faster syllable repetition rates, an initial voiced consonant, and 2-syllable word productions. Results Eleven oral air pressure waveform shapes were identified during the lip occlusions, and plausible physiological explanations for each shape are provided based on the tasks in which they occurred. Training the use of the standard condition, the initial voice consonant condition, and the 2-syllable word production increased the likelihood of rectangular oral air pressure waveform shapes. Increasing the rate beyond 1.5 syllables/s improved the probability of producing rectangular oral air pressure signal shapes in some participants. Conclusions Visual and verbal feedback improved the likelihood of producing rectangular oral air pressure signal shapes. The physiological explanations of variations in the oral air pressure waveform shape may provide direction to the clinician or researcher when providing feedback to increase the accuracy of estimating subglottal pressure from oral air pressure.

Measurement of the Air Pressure for a Rotary Vane Compressor

2003 ◽  
Author(s):  
Yuan Mao Huang ◽  
Sheng An Yang
Keyword(s):  
Frequency Converter ◽  
Air Pressure ◽  
Cover Plate ◽  
Rotary Compressor ◽  
Compression Phase ◽  
Pressure Transducers ◽  
Compressor Rotor ◽  
Two Phases ◽  
Rotary Vane Compressor ◽  
Type Pressure

This study introduces an experimental method that can measure air pressures in the vane segments when a sliding-vane rotary compressor performs suction and compression phases in stable or unstable rotational speeds. When the air pressures of these two phases can be measured, the intake effect of the compressor’s inlet and the seal effect of the vane segments can be evaluated, respectively. Because a frequency converter provides unstable rotational speeds when it controls rotational speeds of a motor with a compressor, an encoder mounted on the output shaft of the motor was applied to record the angular location of the compressor rotor. Two strain gauge type pressure transducers were inserted into the cover plate of the compressor to measure air pressures in the vane segments. Comparing the signals of the encoder with pressure transducers, the air pressures in completions of suction and compression phases could be determined in stable or unstable rotational speeds. The air pressures when the compressor performed suction and compression phases were 99.5 kPa and 153 kPa, respectively, in 1400 rpm. The air pressure when the compressor performed suction phase decreased with the rotational speed faster than 800 rpm. The size or shape of the inlet port of the compressor should be enlarged or modified to provide the suction air pressure without dropping too much. The designed air pressure when the compressor performed compression phase was 244 kPa in 140 rpm, the manufacture precision of the compressor should be increased to decrease leakage.

Sign in / Sign up

Export Citation Format

Share Document