Aerodynamic noise characteristics of the flow past a circular cylinder

2020 ◽  
Vol 68 (5) ◽  
pp. 328-338
Author(s):  
M.G. Arun ◽  
T.J.S. Jothi
Keyword(s):  
Circular Cylinder ◽  
Aerodynamic Noise ◽  
Stream Velocity ◽  
Tone Frequency ◽  
Subcritical Regime ◽  
Noise Characteristics ◽  
Flow Past ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Acoustic Spectra

The present study experimentally investigates the aerodynamic noise from the flow past a fixed circular cylinder. The cylinders considered for the study have the diameters (d) in the range of 6 to 25 mm while its span length (L) is constant, which is 300 mm. The free stream velocity is varied up to 50 m/s, and the corresponding Reynolds number (based on d) varies up to 8.3 104, thus maintaining the flow past the cylinder in the subcritical regime. The discrete narrowband frequency tones depicting the aeolian tones are noted in the spectra. The results showed that the aeolian tone frequency decreases with an increase in the cylinder diameter and ceases to exist beyond the diameter of 15 mm. The corresponding Strouhal number of these tones is found to be in the range of 0.18 to 0.21, which is in congruence with the vortex shedding frequency in the subcritical regime. The maximum overall sound pressure level for cylinders having tonal noise is higher by around 30 dB compared to the background noise. Directivity studies show that the noise level is higher along the perpendicular direction of the jet flow. A sixth power Mach number scaling of the acoustic spectra shows a good collapse of the acoustic tonal amplitude.

Vortex shedding from a rectangular prism and a circular cylinder placed vertically in a turbulent boundary layer

1983 ◽  
Vol 126 ◽  
pp. 147-165 ◽  
Author(s):  
Hiroshi Sakamoto ◽  
Mikio Arie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Vortex Shedding ◽  
Rectangular Prism ◽  
Stream Velocity ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Two Bodies

Measurements of the vortex-shedding frequency behind a vertical rectangular prism and a vertical circular cylinder attached to a plane wall are correlated with the characteristics of the smooth-wall turbulent boundary layer in which they are immersed. Experimental data were collected to investigate the effects of (i) the aspect ratio of these bodies and (ii) the boundary-layer characteristics on the vortex-shedding frequency. The Strouhal number for the rectangular prism and the circular cylinder, defined by S = fcw/U0 and fcd/U0 respectively, was found to be expressed by a power function of the aspect ratio h/w (or h/d). Here fc is the vortex-shedding frequency, U0 is the free-stream velocity, h is the height, w is the width and d is the diameter. As the aspect ratio is reduced, the type of vortex shedding behind each of the two bodies was found to change from the Karman-type vortex to the arch-type vortex at the aspect ratio of 2·0 for the rectangular prism and 2·5 for the circular cylinder.

A Numerical Investigation of the Effects of Flow Pulsations on the Drag Force Over a Cylinder

2011 ◽  
Author(s):  
Eric D’herde ◽  
Laila Guessous
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Drag Coefficient ◽  
Natural Frequency ◽  
Vortex Shedding ◽  
Free Stream ◽  
Stream Velocity ◽  
Vortex Shedding Frequency ◽  
The Mean ◽  
Shedding Frequency

Flow over a cylinder is a fundamental fluid mechanics problem that involves a simple geometry, yet increasingly complex flow patterns as the Reynolds number is increased, most notably the development of a Karman vortex with a natural vortex shedding frequency fs when the Reynolds number exceeds a value of about 40. The goal of this ongoing study is to numerically investigate the effect of an incoming free-stream velocity pulsation with a mean Reynolds number of 100 on the drag force over and vorticity dynamics behind a circular cylinder. This paper reports on initial results involving unsteady, laminar and incompressible flows over a circular cylinder. Sinusoidal free-stream pulsations with amplitudes Av varying between 25% and 75% of the mean free-stream velocity and frequencies f varying between 0.25 and 5 times the natural shedding frequency were considered. Of particular interest to us is the interaction between the pulsating frequency and natural vortex shedding frequency and the resulting effects on drag. Interestingly, at frequencies close to the natural frequency, and to twice the natural frequency, a sudden drop in the mean value of the drag coefficient is observed. This drop in the drag coefficient is also accompanied by a change in the flow and vortex shedding patterns observed behind the cylinder.

A Numerical Investigation of the Effects of Flow Pulsations on the Vortex Shedding, Drag and Lift Forces Over a Cylinder

2011 ◽  
Author(s):  
Eric D’herde ◽  
Laila Guessous
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Vortex Shedding ◽  
Free Stream ◽  
Lift Coefficient ◽  
Stream Velocity ◽  
Vortex Shedding Frequency ◽  
The Mean ◽  
Shedding Frequency ◽  
Drag And Lift

Flow over a cylinder is a fundamental fluid mechanics problem that involves a simple geometry, yet increasingly complex flow patterns as the Reynolds number is increased, most notably the development of a Karman vortex with a natural vortex shedding frequency when the Reynolds number exceeds a value of about 40. The goal of this ongoing study is to numerically investigate the effect of an incoming free-stream velocity pulsation with a mean Reynolds number of 100 on the drag and lift forces over and vorticity dynamics behind a circular cylinder. This paper reports on initial results involving unsteady, laminar and incompressible flows over a circular cylinder. Sinusoidal free-stream pulsations with amplitudes Av varying between 25% and 75% of the mean free-stream velocity and frequencies varying between 0.25 and 5 times the natural shedding frequency fs were considered. Of particular interest to us is the interaction between the pulsating frequency and natural vortex shedding frequency and the resulting effects on drag. Interestingly, at frequencies close to the natural frequency, and to twice the natural frequency, a sudden drop in the mean value of the drag coefficient is observed. The first drop in the drag coefficient, i.e. near f = fs, is also accompanied by a change in the flow and vortex shedding patterns observed behind the cylinder. This change in vortex shedding pattern manifests itself as a departure from symmetrical shedding, and in a non-zero mean lift coefficient value. The second drop, i.e. near f = 2 fs, has similar characteristics, except that the mean lift coefficient remains at zero.

Flow-Induced Vibration of a Cylinder in the Wake of Another of Smaller Diameter

2014 ◽  
Author(s):  
Md. Mahbub Alam ◽  
An Ran ◽  
Yu Zhou
Keyword(s):  
Circular Cylinder ◽  
Free Stream ◽  
Cross Flow ◽  
Induced Response ◽  
Stream Velocity ◽  
Flow Induced Vibration ◽  
Cylinder Diameter ◽  
Spacing Ratio ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

This paper presents cross-flow induced response of a both-end-spring-mounted circular cylinder (diameter D) placed in the wake of a rigid circular cylinder of smaller diameter d. The cylinder vibration is constrained to the transverse direction. The cylinder diameter ratio d/D and spacing ratio L/d are varied from 0.2 to 1.0 and 1.0 to 5.5, respectively, where L is the distance between the center of the upstream cylinder to the forward stagnation point of the downstream cylinder. A violent vibration of the cylinder is observed for d/D = 0.2 ∼ 0.8 at L/d = 1.0, for d/D = 0.24 ∼ 0.6 at 1.0 < L/d ≤ 2.5, for d/D = 0.2 ∼ 0.4 at 2.5 < L/d ≤ 3.5, and for d/D = 0.2 at 3.5 < L/d ≤ 5.5, but not for d/D = 1.0. A smaller d/D generates vibration for a longer range of L/d. The violent vibration occurs at a reduced velocity Ur (=U∞/fnD, where U∞ is the free-stream velocity and fn the natural frequency of the cylinder system) beyond the vortex excitation regime (Ur ≥ 8) depending on d/D and L/d. Once the vibration starts to occur, the vibration amplitude increases rapidly with increasing Ur. It is further noted that the flow behind the downstream cylinder is characterized by two predominant frequencies, corresponding to the cylinder vibration frequency and the natural vortex shedding frequency of the cylinder, respectively. While the former persists downstream, the latter vanishes rapidly.

The Effect of Uniform Blowing on the Flow Past a Circular Cylinder

2002 ◽  
Vol 124 (2) ◽  
pp. 452-464 ◽  
Author(s):  
Lionel Mathelin ◽  
Franc¸oise Bataille ◽  
Andre´ Lallemand
Keyword(s):  
Circular Cylinder ◽  
Stream Flow ◽  
Boundary Layer Thickness ◽  
Free Stream ◽  
Thermal Protection ◽  
Viscous Drag ◽  
Near Wake ◽  
Flow Past ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

This work describes blowing through the whole surface of a porous circular cylinder for the control of the near wake dynamics and the thermal protection of the surface. The flow past the cylinder is numerically studied and the blowing is modeled. Comparisons with experimental data are used for validation. It is shown that the blowing tends to increase the boundary layer thickness, to promote its separation and to decrease the viscous drag induced. Similarly, the convective heat transfer is lowered, and in the case of a nonisothermal blowing, the surface is very effectively protected from the hot free stream flow. The near wake is also affected. The vortex shedding frequency is shown to decrease when blowing occurs and a qualitative model is presented to identify the different mechanisms.

The flow past a rapidly rotating circular cylinder

1957 ◽  
Vol 242 (1228) ◽  
pp. 108-115 ◽  
Keyword(s):  
Boundary Layer ◽  
Circular Cylinder ◽  
Present Theory ◽  
Stream Velocity ◽  
Two Dimensional ◽  
Rotating Circular Cylinder ◽  
Flow Past ◽  
Separating Flow ◽  
Two Dimensional Flow ◽  
Uniform Stream

This paper considers the two-dimensional flow past a circular cylinder immersed in a uniform stream, when the cylinder rotates about its axis so fast that separation in suppressed. The solution of the flow in the boundary layer on the cylinder is obtained in the form of a power series in the ratio of the stream velocity to the cylinder's peripheral velocity, and expressions are deduced for the value of the circulation and the torque on the cylinder. The terms calculated explicitly are sufficient to give reliable numerical values over the whole range of rotational speeds for which the postulate of non-separating flow is justifiable. The previously accepted theory, due to Prandtl, predicted that the circulation should not exceed a certain limit, while the present theory indicates that the circulation increases indefinitely with increase of rotaional speed. Strong arguments against the older theory are put forward, but the experimental evidence available is inconclusive.

Flow past a rotationally oscillating cylinder

2013 ◽  
Vol 735 ◽  
pp. 307-346 ◽  
Author(s):  
S. Kumar ◽  
C. Lopez ◽  
O. Probst ◽  
G. Francisco ◽  
D. Askari ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Three Dimensional ◽  
Far Field ◽  
Two Dimensional ◽  
Flow Past ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Flow Visualizations ◽  
Hydrogen Bubble Technique

AbstractFlow past a circular cylinder executing sinusoidal rotary oscillations about its own axis is studied experimentally. The experiments are carried out at a Reynolds number of 185, oscillation amplitudes varying from $\mathrm{\pi} / 8$ to $\mathrm{\pi} $, and at non-dimensional forcing frequencies (ratio of the cylinder oscillation frequency to the vortex-shedding frequency from a stationary cylinder) varying from 0 to 5. The diagnostic is performed by extensive flow visualization using the hydrogen bubble technique, hot-wire anemometry and particle-image velocimetry. The wake structures are related to the velocity spectra at various forcing parameters and downstream distances. It is found that the phenomenon of lock-on occurs in a forcing frequency range which depends not only on the amplitude of oscillation but also the downstream location from the cylinder. The experimentally measured lock-on diagram in the forcing amplitude and frequency plane at various downstream locations ranging from 2 to 23 diameters is presented. The far-field wake decouples, after the lock-on at higher forcing frequencies and behaves more like a regular Bénard–von Kármán vortex street from a stationary cylinder with vortex-shedding frequency mostly lower than that from a stationary cylinder. The dependence of circulation values of the shed vortices on the forcing frequency reveals a decay character independent of forcing amplitude beyond forcing frequency of ${\sim }1. 0$ and a scaling behaviour with forcing amplitude at forcing frequencies ${\leq }1. 0$. The flow visualizations reveal that the far-field wake becomes two-dimensional (planar) near the forcing frequencies where the circulation of the shed vortices becomes maximum and strong three-dimensional flow is generated as mode shape changes in certain forcing parameter conditions. It is also found from flow visualizations that even at higher Reynolds number of 400, forcing the cylinder at forcing amplitudes of $\mathrm{\pi} / 4$ and $\mathrm{\pi} / 2$ can make the flow field two-dimensional at forcing frequencies greater than ${\sim }2. 5$.

Influence of slip on the flow past superhydrophobic circular cylinders

2011 ◽  
Vol 680 ◽  
pp. 459-476 ◽  
Author(s):  
PRANESH MURALIDHAR ◽  
NANGELIE FERRER ◽  
ROBERT DANIELLO ◽  
JONATHAN P. ROTHSTEIN
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Flow Direction ◽  
Superhydrophobic Surfaces ◽  
Separation Point ◽  
Circular Cylinders ◽  
Recirculation Region ◽  
Small Scale ◽  
Flow Past ◽  
Shedding Frequency

Superhydrophobic surfaces have been shown to produce significant drag reduction for both laminar and turbulent flows of water through large- and small-scale channels. In this paper, a series of experiments were performed which investigated the effect of superhydrophobic-induced slip on the flow past a circular cylinder. In these experiments, circular cylinders were coated with a series of superhydrophobic surfaces fabricated from polydimethylsiloxane with well-defined micron-sized patterns of surface roughness. The presence of the superhydrophobic surface was found to have a significant effect on the vortex shedding dynamics in the wake of the circular cylinder. When compared to a smooth, no-slip cylinder, cylinders coated with superhydrophobic surfaces were found to delay the onset of vortex shedding and increase the length of the recirculation region in the wake of the cylinder. For superhydrophobic surfaces with ridges aligned in the flow direction, the separation point was found to move further upstream towards the front stagnation point of the cylinder and the vortex shedding frequency was found to increase. For superhydrophobic surfaces with ridges running normal to the flow direction, the separation point and shedding frequency trends were reversed. Thus, in this paper we demonstrate that vortex shedding dynamics is very sensitive to changes of feature spacing, size and orientation along superhydrophobic surfaces.

Flow Around a Normal Plate of Finite Width Immersed in a Turbulent Boundary Layer

1983 ◽  
Vol 105 (1) ◽  
pp. 98-104 ◽  
Author(s):  
H. Sakamoto ◽  
M. Arie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Power Function ◽  
Vortex Shedding ◽  
Stream Velocity ◽  
Finite Width ◽  
Pressure Drag ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

An experimental investigation was carried out on the flow around a normal plate of finite width mounted on a smooth plane wall along which a turbulent boundary layer was fully developed. Experimental data were collected to investigate the effects of (1) the aspect ratio of the plate (2) the parameters characterizing the boundary-layer on the pressure drag and the vortex shedding frequency. The pressure drag coefficient of the plate defined by CDτ = D/(1/2ρuτ2hw) was found to be expressed by a power function of huτ/ν in the range h/δ<1.0 for each aspect ratio w/h, where D is the pressure drag, uτ is the shear velocity, ρ is the density of fluid, h and w are the height and the width of the plate, respectively, ν is the kinematic viscosity, δ is the thickness of the boundary layer. Also, the Strouhal number for the plate defined by St =fc • w/ U0 was found to be expressed by a power function of the aspect ratio w/h in the range of h/δ less than about 1.0, where fc is the vortex shedding frequency, U0 is the free-stream velocity. As the aspect ratio was reduced, the type of vortex shedding behind the plate was found to change from the arch type to the Karman type at the aspect ratio of about 0.8.

scholarly journals Visualization of flow past square cylinders with corner modification

2020 ◽  
Vol 4 (3) ◽  
pp. 285-294
Author(s):  
Ch. Krishnappa Vikram ◽  
H. V. Ravindra ◽  
Y. T. Krishnegowda
Keyword(s):  
Aluminum Powder ◽  
Experimental Work ◽  
Vortex Shedding ◽  
Test Section ◽  
Square Cylinder ◽  
Square Cylinders ◽  
Flow Past ◽  
Spacing Ratio ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

This article presents the results for flow past a square cylinder and two square cylinders of the same and different sizes with corner modifications by varying the spacing ratio. Here, experimental work is conducted in a recirculatory channel filled with water. A set of aluminum discs made to rotate to create the flow in the test section. The motor is used to vary the speed of the water. Fine aluminum powder is used as a tracer medium. It is observed that vortex shedding frequency decreases by placing the second cylinder in the downstream of the first cylinder. For similar size cylinders, the width of the eddy in the middle of the cylinders increases with an increase in spacing ratio. With the increase of spacing ratio to 6, the flow past each cylinder behaves like a single square cylinder. If the upstream square cylinder size is smaller than the downstream square cylinder, the eddy size is reduced in between the cylinder compared to the downstream of the second cylinder. If the upstream square cylinder size is bigger than the downstream square cylinder, the eddy size is larger in between the cylinder compared to the downstream of the second cylinder.

Sign in / Sign up

Export Citation Format

Share Document