scholarly journals Thermal Processes Associated with Pelleting and Feed Phosphate Variation in Diets on Feed Manufacture and Broiler Performance

2017 ◽  
Author(s):  
Ariel N. Bergeron
Keyword(s):  
Thermal Processes ◽  
Broiler Performance ◽  
Feed Manufacture

scholarly journals Effects of calcium lignosulfonate, mixer-added fat, and feed form on feed manufacture and broiler performance

2014 ◽  
Vol 23 (3) ◽  
pp. 418-428 ◽  
Author(s):  
A.M. Corey ◽  
K.G.S. Wamsley ◽  
T.S. Winowiski ◽  
J.S. Moritz
Keyword(s):  
Broiler Performance ◽  
Feed Form ◽  
Feed Manufacture

Research and Modelling on Electrical and Thermal Mode of LEDs Operation in the Luminaire

2018 ◽  
pp. 155-162 ◽  
Author(s):  
Sergei S. Kapitonov ◽  
Anastasia V. Kapitonova ◽  
Sergei Yu. Grigorovich ◽  
Sergei A. Medvedev ◽  
Taher Sobhy
Keyword(s):  
Thermal Conditions ◽  
Operating Mode ◽  
Thermal Processes ◽  
Thermal Mode ◽  
Crystal Temperature ◽  
Premature Failure ◽  
Model Based

In the article, the electrical and thermal processes in the LED lamp with varied parameters are investigated. Voltage and current measurements on all LEDs of the luminaire are carried out in the nominal operating mode. The power allocated to each LED is determined. The calculation of the LED crystal temperature was carried out using the developed thermal LED model based on the results of the measurements and by using “Multisim” program. It has been established that the temperature of the crystals of individual LEDs in the luminaire differ significantly, which leads to unfavourable thermal conditions for them and an increased likelihood of premature failure.

INFLUENCE OF HEAT TREATMENT OF MOUNTAIN MASSIVE ON TEMPERATURE MODE OF GEOTHERMAL CIRCULATION SYSTEM

2018 ◽  
pp. 44-50
Author(s):  
Yu. P. Morozov
Keyword(s):  
Heat Transfer ◽  
Operating Time ◽  
Fluid Motion ◽  
Coolant Temperature ◽  
Circulation System ◽  
Thermal Processes ◽  
Temperature Mode ◽  
Heat Influx ◽  
Stationary Heat Transfer

Based on the solution of the problem of non-stationary heat transfer during fluid motion in underground permeable layers, dependence was obtained to determine the operating time of the geothermal circulation system in the regime of constant and falling temperatures. It has been established that for a thickness of the layer H <4 m, the influence of heat influxes at = 0.99 and = 0.5 is practically the same, but for a thickness of the layer H> 5 m, the influence of heat inflows depends significantly on temperature. At a thickness of the permeable formation H> 20 m, the heat transfer at = 0.99 has virtually no effect on the thermal processes in the permeable formation, but at = 0.5 the heat influx, depending on the speed of movement, can be from 50 to 90%. Only at H> 50 m, the effect of heat influx significantly decreases and amounts, depending on the filtration rate, from 50 to 10%. The thermal effect of the rock mass with its thickness of more than 10 m, the distance between the discharge circuit and operation, as well as the speed of the coolant have almost no effect on the determination of the operating time of the GCS in constant temperature mode. During operation of the GCS at a dimensionless coolant temperature = 0.5, the velocity of the coolant is significant. With an increase in the speed of the coolant in two times, the error changes by 1.5 times.

Sign in / Sign up

Export Citation Format

Share Document