Yerba Mate (Ilex paraguarensis) as Bio-Adsorbent for the Removal of Methylene Blue, Remazol Brilliant Blue and Chromium Hexavalent: Thermodynamic and Kinetic Studies

Leone Mazzeo; Irene Bavasso; Maria Paola Bracciale; Marco Cocchi; Luca Di Palma; Vincenzo Piemonte

doi:10.3390/w12072016

Green Tea Waste as an Efficient Adsorbent for Methylene Blue: Structuring of a Novel Adsorbent Using Full Factorial Design

Molecules ◽

10.3390/molecules26206138 ◽

2021 ◽

Vol 26 (20) ◽

pp. 6138

Author(s):

Marwa El-Azazy ◽

Ahmed S. El-Shafie ◽

Bayan Al-Shaikh Al-Shaikh Yousef

Keyword(s):

Methylene Blue ◽

Factorial Design ◽

Adsorption Capacity ◽

Green Tea ◽

Full Factorial Design ◽

Bet Analysis ◽

Tea Waste ◽

Full Factorial ◽

Mb Adsorption ◽

Thermally Treated

Adsorptive removal of methylene blue (MB) from contaminated water samples was achieved using green tea waste (GTW). Adsorption of MB onto raw (RGTW) and thermally treated waste (TTGTW250–TTGTW500) was explored. The performance of the tested adsorbents was assessed in terms of percentage removal of MB (%R) and adsorption capacity (qe, mg/g). A full factorial design (FFD) was employed to optimize the adsorption of MB onto both RGTW and TTGTW500. Four factors were studied: pH, adsorbent dose (AD), dye concentration (DC), and contact time (CT). Value for %R of 96.58% and 98.07% were obtained using RGTW and TTGTW500, respectively. FT-IR and Raman analyses were used to study the surfaces of the prepared adsorbents, and the IR spectrum showed the existence of a variety of functionalities on the surfaces of both the RGTW and thermally treated samples. BET analysis showed the presence of mesopores and macropores in the case of RGTW and micropores in the case of thermally processed adsorbents. Equilibrium studies indicated that the Freundlich isotherm best described the adsorption of MB onto both adsorbents. The maximum adsorption capacity (qmax) was found to be 68.28 and 69.01 mg/g for RGTW and TTGTW500, respectively, implying the superior capacity of TTGTW500 in removing MB. Adsorption of MB was found to proceed via chemisorption (RGTW) and physisorption (TTGTW500), as indicated by the Dubinin–Radushkevich (D-R) isotherm. A pseudo-second order (PSO) model best demonstrated the kinetics of the MB adsorption onto both adsorbents.

Download Full-text

Biopolymeric Adsorbent for the Removal of Methylene Blue: Characterizations, Equilibrium Isotherms and Kinetic Studies

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.1125.281 ◽

2015 ◽

Vol 1125 ◽

pp. 281-285

Author(s):

Siti Aishah Muhmed ◽

Mohd Ghazali Mohd Nawawi

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Correlation Coefficient ◽

Kinetic Studies ◽

Second Order ◽

Equilibrium Isotherms ◽

Chi Square ◽

Initial Concentration ◽

Adsorbent Dosage ◽

Pseudo Second Order

Crosslinked Sago Starch (CSS) was prepared by crosslinking native starch with Sodium Trimetaphosphate. As a biodegradable adsorbent, CSS was used to remove methylene blue (MB) from the aqueous solution based on its characterization, including the granule morphology, crystalline nature and molecular structure. The adsorption capacity of CSS was evaluated as a function of pH, adsorbent dosage, initial concentration and time. It was favorable for adsorption under condition of neutral and at high initial concentration. The adsorption capacity trend was decreased with increasing the adsorbent dosage. The equilibrium isotherms were conducted using Langmuir, Freundlich and Tempkin model. It has been demonstrated that the better agreement was Langmuir isotherm with correlation coefficient of 0.99, equilibrium adsorption capacity of 3.75 mg g-1, chi-square test, χ2 of 0.03% and corresponding contact time of 4 hours. The pseudo-first-order, pseudo-second-order and intra-particle diffusion were used to fit adsorption data in the kinetic studies. And results showed that the adsorption kinetics was more accurately described by the pseudo-second-order model with correlation coefficient, R2 of 0.99 and standard deviation, SSE of 0.12%. The obtained results suggest that CSS could be promising candidates as an adsorbent for dye removal.

Download Full-text

Mg-Cr Layered Double Hydroxide Intercalated Oxalic Anion to Remove Cationic Dye Solutions: Rhodamine B and Methylene Blue

Journal of Environmental Treatment Techniques ◽

10.47277/jett/9(2)391 ◽

2020 ◽

Vol 9 (2) ◽

pp. 383-391

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Layered Double Hydroxide ◽

Rhodamine B ◽

Physical Adsorption ◽

Dye Adsorption ◽

Kinetic Studies ◽

Economic Feasibility ◽

Order Kinetic ◽

Double Hydroxide

A MgCr-based layered double hydroxide (LDH) was synthesized by a coprecipitation method, followed by an intercalation process using an oxalic anion. The materials were characterized using X-ray diffraction analysis, FT-IR spectroscopy, and pH pzc measurement. The materials were then applied as adsorbents for removal of methylene blue (MB) and rhodamine B (RhB) from aqueous solution. Pristine Mg/Cr LDH exhibited RhB adsorption capacity of 32.154 mg g⁻1, whereas the use of intercalated Mg/Cr LDH caused an increase in the capacity (139.526 mg g⁻1). Kinetic studies indicated that the dye adsorption using both LDHs followed a pseudo-second-order kinetic model; the K2 values of pristine and modified Mg/Cr LDH for RhB and MB were 6.970, 0.001, 0.426, and 2.056 g mg⁻1 min⁻1, respectively. The thermodynamic study identified that the adsorption of both dyes onto the LDHs was a spontaneous process and can be classified as physical adsorption with adsorption energies of <40 kJ/mol. Moreover, the desorption and regeneration experiments indicated the high economic feasibility and reusability of the LDHs. By using HCl as the optimal solvent, the LDHs could desorb as much as 98% of the dye and could be used as adsorbents with high adsorption capacity over three cycles.

Download Full-text

Equilibrium and kinetic studies on MB adsorption by ultrathin 2D MoS2 nanosheets

RSC Advances ◽

10.1039/c5ra24328a ◽

2016 ◽

Vol 6 (14) ◽

pp. 11631-11636 ◽

Cited By ~ 88

Author(s):

Xiu-Qing Qiao ◽

Fu-Chao Hu ◽

Feng-Yu Tian ◽

Dong-Fang Hou ◽

Dong-Sheng Li

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Kinetic Studies ◽

Deionized Water ◽

Maximum Adsorption Capacity ◽

Mos2 Nanosheets ◽

Adsorption Ability ◽

Ultrathin Nanosheets ◽

Mb Adsorption

MoS2 ultrathin nanosheets display excellent adsorption ability towards methylene blue, with a maximum adsorption capacity of 146.43 mg g−1 in 300 seconds. Moreover, the adsorbent can be resued by washing with deionized water.

Download Full-text

Parametric and adsorption kinetic studies of methylene blue removal from simulated textile water using durian (Durio zibethinus murray) skin

Water Science & Technology ◽

10.2166/wst.2015.247 ◽

2015 ◽

Vol 72 (6) ◽

pp. 896-907 ◽

Cited By ~ 18

Author(s):

S. M. Anisuzzaman ◽

Collin G. Joseph ◽

D. Krishnaiah ◽

A. Bono ◽

L. C. Ooi

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Dye Adsorption ◽

Freundlich Isotherm ◽

Kinetic Studies ◽

Isotherm Models ◽

Batch Adsorption ◽

Maximum Adsorption Capacity ◽

Order Kinetic ◽

Durio Zibethinus

In this study, durian (Durio zibethinus Murray) skin was examined for its ability to remove methylene blue (MB) dye from simulated textile wastewater. Adsorption equilibrium and kinetics of MB removal from aqueous solutions at different parametric conditions such as different initial concentrations (2–10 mg/L), biosorbent dosages (0.3–0.7 g) and pH solution (4–9) onto durian skin were studied using batch adsorption. The amount of MB adsorbed increased from 3.45 to 17.31 mg/g with the increase in initial concentration of MB dye; whereas biosorbent dosage increased from 1.08 to 2.47 mg/g. Maximum dye adsorption capacity of the durian skin was found to increase from 3.78 to 6.40 mg/g, with increasing solution pH. Equilibrium isotherm data were analyzed according to Langmuir and Freundlich isotherm models. The sorption equilibrium was best described by the Freundlich isotherm model with maximum adsorption capacity of 7.23 mg/g and this was due to the heterogeneous nature of the durian skin surface. Kinetic studies indicated that the sorption of MB dye tended to follow the pseudo second-order kinetic model with promising correlation of 0.9836 < R2 < 0.9918.

Download Full-text

Mg-Cr Layered Double Hydroxide with Intercalated Oxalic Anion for Removal Cationic Dyes Rhodamine B and Methylene Blue

Journal of Environmental Treatment Techniques ◽

10.47277/jett/9(1)94 ◽

2020 ◽

Vol 9 (1) ◽

pp. 85-94

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Layered Double Hydroxide ◽

Rhodamine B ◽

Physical Adsorption ◽

Dye Adsorption ◽

Kinetic Studies ◽

Economic Feasibility ◽

Order Kinetic ◽

Double Hydroxide

A MgCr-based layered double hydroxide (LDH) was synthesized by a coprecipitation method, followed by an intercalation process using an oxalic anion. The materials were characterized using X-ray diffraction analysis, FT-IR spectroscopy, and pH pzc measurement. The materials were then applied as adsorbents for removal of methylene blue (MB) and rhodamine B (RhB) from aqueous solution. Pristine Mg/Cr LDH exhibited RhB adsorption capacity of 32.154 mg g⁻1, whereas the use of intercalated Mg/Cr LDH caused an increase in the capacity (139.526 mg g⁻1). Kinetic studies indicated that the dye adsorption using both LDHs followed a pseudo-second-order kinetic model; the K2 values of pristine and modified Mg/Cr LDH for RhB and MB were 6.970, 0.001, 0.426, and 2.056 g mg⁻1 min⁻1, respectively. The thermodynamic study identified that the adsorption of both dyes onto the LDHs was a spontaneous process and can be classified as physical adsorption with adsorption energies of <40 kJ/mol. Moreover, the desorption and regeneration experiments indicated the high economic feasibility and reusability of the LDHs. By using HCl as the optimal solvent, the LDHs could desorb as much as 98% of the dye and could be used as adsorbents with high adsorption capacity over three cycles.

Download Full-text

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

Jurnal Penelitian Pendidikan Fisika ◽

10.36709/jipfi.v5i3.13803 ◽

2020 ◽

Vol 5 (3) ◽

pp. 221

Author(s):

Muhammad Azam ◽

Muhammad Anas ◽

Erniwati Erniwati

Keyword(s):

Methylene Blue ◽

Activated Carbon ◽

Adsorption Capacity ◽

Temperature Variation ◽

Chemical Activation ◽

Weight Ratio ◽

Potassium Silicate ◽

Physical Activation ◽

Activation Temperature ◽

Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

Download Full-text

One-step synthesis of nitrogen-grafted copper-gallic acid for enhanced methylene blue removal

Scientific Reports ◽

10.1038/s41598-021-91484-w ◽

2021 ◽

Vol 11 (1) ◽

Author(s):

Shella Permatasari Santoso ◽

Vania Bundjaja ◽

Artik Elisa Angkawijaya ◽

Chintya Gunarto ◽

Alchris Woo Go ◽

...

Keyword(s):

Methylene Blue ◽

Adsorption Capacity ◽

Gallic Acid ◽

Synthesis Method ◽

Molar Ratio ◽

X Ray Diffraction ◽

Temperature Dependent ◽

One Step ◽

Detailed Assessment ◽

Higher Temperature

AbstractNitrogen-grafting through the addition of glycine (Gly) was performed on a metal- phenolic network (MPN) of copper (Cu2+) and gallic acid (GA) to increase its adsorption capacity. Herein, we reported a one-step synthesis method of MPN, which was developed according to the metal–ligand complexation principle. The nitrogen grafted CuGA (Ng-CuGA) MPN was obtained by reacting Cu2+, GA, and Gly in an aqueous solution at a molar ratio of 1:1:1 and a pH of 8. Several physicochemical measurements, such as Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), N2 sorption, X-ray diffraction (XRD), and thermal gravimetry analysis (TGA), were done on Ng-CuGA to elucidate its characteristics. The analysis revealed that the Ng-CuGA has non-uniform spherical shaped morphology with a pore volume of 0.56 cc/g, a pore size of 23.25 nm, and thermal stability up to 205 °C. The applicational potential of the Ng-CuGA was determined based on its adsorption capacity against methylene blue (MB). The Ng-CuGA was able to adsorb 190.81 mg MB per g adsorbent at a pH of 6 and temperature of 30 °C, which is 1.53 times higher than the non-grafted CuGA. Detailed assessment of Ng-CuGA adsorption properties revealed their pH- and temperature-dependent nature. The adsorption capacity and affinity were found to decrease at a higher temperature, demonstrating the exothermic adsorption behavior.

Download Full-text

Hydrothermal Synthesis of Sodalite-Type N-A-S-H from Fly Ash to Remove Ammonium and Phosphorus from Water

Materials ◽

10.3390/ma14112741 ◽

2021 ◽

Vol 14 (11) ◽

pp. 2741

Author(s):

Pengcheng Lv ◽

Ruihong Meng ◽

Zhongyang Mao ◽

Min Deng

Keyword(s):

Fly Ash ◽

Adsorption Capacity ◽

Removal Rate ◽

Kinetic Studies ◽

Solute Concentration ◽

Raw Material ◽

Sodium Aluminosilicate ◽

Equilibrium Data ◽

One Step ◽

Ft Ir

In this study, the hydrated sodium aluminosilicate material was synthesized by one-step hydrothermal alkaline desilication using fly ash (FA) as raw material. The synthesized materials were characterized by XRD, XRF, FT-IR and SEM. The characterization results showed that the alkali-soluble desilication successfully had synthesized the sodium aluminosilicate crystalline (N-A-S-H) phase of sodalite-type (SOD), and the modified material had good ionic affinity and adsorption capacity. In order to figure out the suitability of SOD as an adsorbent for the removal of ammonium and phosphorus from wastewater, the effects of material dosing, contact time, ambient pH and initial solute concentration on the simultaneous removal of ammonium and phosphorus are investigated by intermittent adsorption tests. Under the optimal adsorption conditions, the removal rate of ammonium was 73.3%, the removal rate of phosphate was 85.8% and the unit adsorption capacity reached 9.15 mg/L and 2.14 mg/L, respectively. Adsorption kinetic studies showed that the adsorption of ammonium and phosphorus by SOD was consistent with a quasi-secondary kinetic model. The adsorption isotherm analysis showed that the equilibrium data were in good agreement with the Langmuir and Freundlich model. According to thermodynamic calculations, the adsorption of ammonium and phosphorus was found to be a heat-absorbing and spontaneous process. Therefore, the preparation of SOD by modified FA has good adsorption properties as adsorbent and has excellent potential for application in the removal of contaminants from wastewater.

Download Full-text