scholarly journals Comparisons of Local Scouring for Submerged Square and Circular Cross-Section Piles in Steady Currents

Water ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1820
Author(s):  
Shengtao Du ◽  
Bingchen Liang
Keyword(s):  
Cross Section ◽  
Boundary Point ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Scour Depth ◽  
Two Dimensional ◽  
Exponential Equation ◽  
Equilibrium Scour Depth ◽  
Over Time

The local scouring that occurs around submerged vertical piles in steady currents was studied experimentally in this paper. Three experiments were carried out for square cross-section (SC) piles and a circular cross-section (CC) pile with the same width. The key point scour depths, including the center of the upstream boundary point (KC) and the two upstream corners (KM), were observed over time. The two-dimensional profiles and the three-dimensional topography around each pile were measured using a Seatek. The different scouring characteristics of the SC and CC piles were investigated. The experiment results show that the scour depth at KC is much smaller than that of KM. The equilibrium scour depth of the CC pile is far less than that of the SC piles. The scour and deposition distributions were different between the CC and SC piles. The maximum scour depth was found at the lateral rear of the CC pile, and the maximum deposition was observed in sections of the SC piles. The evolutions of the scour depths at KM are predicted using a developed exponential equation.

scholarly journals Computational Study of Zigzag Spacer Design with Elliptical Cross-Section Filaments

2020 ◽  
Vol 307 ◽  
pp. 01047
Author(s):  
Gohar Shoukat ◽  
Farhan Ellahi ◽  
Muhammad Sajid ◽  
Emad Uddin
Keyword(s):  
Mass Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Computational Study ◽  
Flow Direction ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Two Dimensional ◽  
Permeate Flux ◽  
Elliptical Cross

The large energy consumption of membrane desalination process has encouraged researchers to explore different spacer designs using Computational Fluid Dynamics (CFD) for maximizing permeate per unit of energy consumed. In previous studies of zigzag spacer designs, the filaments are modeled as circular cross sections in a two-dimensional geometry under the assumption that the flow is oriented normal to the filaments. In this work, we consider the 45° orientation of the flow towards the three-dimensional zigzag spacer unit, which projects the circular cross section of the filament as elliptical in a simplified two-dimensional domain. OpenFOAM was used to simulate the mass transfer enhancement in a reverse-osmosis desalination unit employing spiral wound membranes lined with zigzag spacer filaments. Properties that impact the concentration polarization and hence permeate flux were analyzed in the domain with elliptical filaments as well as a domain with circular filaments to draw suitable comparisons. The range of variation in characteristic parameters across the domain between the two different configurations is determined. It was concluded that ignoring the elliptical projection of circular filaments to the flow direction, can introduce significant margin of error in the estimation of mass transfer coefficient.

On the Critical Plunger Speed and Three-Dimensional Effects in High-Pressure Die Casting Injection Chambers

2003 ◽  
Vol 125 (3) ◽  
pp. 529-537 ◽  
Author(s):  
J. Lo´pez ◽  
F. Faura ◽  
J. Herna´ndez ◽  
P. Go´mez
Keyword(s):  
Molten Metal ◽  
Cross Section ◽  
Die Casting ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Water Model ◽  
Two Dimensional ◽  
Shallow Water Model ◽  
One Dimensional ◽  
Pressure Die Casting

During the initial slow stage of the injection process in high-pressure die casting machines with horizontal cold chamber, a plunger pushes the molten metal which partially fills the injection chamber, causing the formation of a gravity wave. The evolution of the wave surface profile, which depends on the plunger acceleration law, may trap air in the molten metal, causing porosity when the metal solidifies. In this work, a one-dimensional shallow-water model, which is solved numerically using the method of characteristics, and a three-dimensional numerical model, based on a finite element formulation and the volume of fluid (VOF) method for treating the free surface, are used to analyze the flow of molten metal in an injection chamber of circular cross section. The results for the evolution of the free surface obtained from both models for different plunger motion laws and initial filling fractions of the injection chamber were in good agreement for broad ranges of operating conditions. The existence of a critical plunger speed, above which the reflection of the wave of molten metal against the chamber ceiling might appreciably increase air entrapment effects, is investigated. The results for the wave profiles in chambers of circular cross section are compared with those obtained in an equivalent two-dimensional configuration of the injection chamber, for which the shallow-water model is solved analytically. It is shown how the results obtained by applying the one-dimensional model to a two-dimensional chamber configuration can be used to reproduce, with an acceptable degree of accuracy, the salient characteristics of the flow of molten metal in a real injection chamber of circular cross section.

SAF file: It's really three dimensional file

2018 ◽  
Vol 14 (1) ◽  
pp. 1
Author(s):  
Prof. Dr. Jamal Aziz Mehdi
Keyword(s):  
Cross Section ◽  
Root Canal ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Circular Motion ◽  
Root Canal Treatment ◽  
Metal Core ◽  
Rotating Blade

The biological objectives of root canal treatment have not changed over the recentdecades, but the methods to attain these goals have been greatly modified. Theintroduction of NiTi rotary files represents a major leap in the development ofendodontic instruments, with a wide variety of sophisticated instruments presentlyavailable (1, 2).Whatever their modification or improvement, all of these instruments have onething in common: they consist of a metal core with some type of rotating blade thatmachines the canal with a circular motion using flutes to carry the dentin chips anddebris coronally. Consequently, all rotary NiTi files will machine the root canal to acylindrical bore with a circular cross-section if the clinician applies them in a strictboring manner

On the Flexural-Torsional Behavior of a Straight Elastic Beam Subject to Terminal Moments

1993 ◽  
Vol 60 (2) ◽  
pp. 498-505 ◽  
Author(s):  
Z. Tan ◽  
J. A. Witz
Keyword(s):  
Coordinate System ◽  
Cross Section ◽  
Equilibrium Equation ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Elastic Beam ◽  
Cartesian Coordinate System ◽  
Kinematic Constraints ◽  
Torsional Behavior ◽  
Cartesian Coordinate

This paper discusses the large-displacement flexural-torsional behavior of a straight elastic beam with uniform circular cross-section subject to arbitrary terminal bending and twisting moments. The beam is assumed to be free from any kinematic constraints at both ends. The equilibrium equation is solved analytically with the full expression for curvature to obtain the deformed configuration in a three-dimensional Cartesian coordinate system. The results show the influence of the terminal moments on the beam’s deflected configuration.

Microstructure Evolution of Epitaxial (Ba, Sr) TiO3/ (001) HgO Thin Films

1994 ◽  
Vol 361 ◽  
Author(s):  
V.A. Alyoshin ◽  
E.V. Sviridov ◽  
V.I.M. Hukhortov ◽  
I.H. Zakharchenko ◽  
V.P. Dudkevich
Keyword(s):  
Thin Films ◽  
Cross Section ◽  
Microstructure Evolution ◽  
Three Dimensional ◽  
Gas Pressure ◽  
Smooth Surfaces ◽  
Two Dimensional ◽  
Surface Versus ◽  
Deposition Conditions

ABSTRACTSurface and cross-section relief evolution of ferroelectric epitaxial (Ba,Sr)TiO3 films rf-sputtered on (001) HgO crystal cle-avage surface versus the oxygen worKing gas pressure P and subst-rate temperature T were studied. Specific features of both three-dimensional and two-dimensional epitaxy mechanisms corresponding to various deposition conditions were revealed. Difference between low and high P-T-value 3D epitaxy was established. The deposition of films with mirror-smooth surfaces and perfect interfaces is shown to be possible.

Plane turbulent jets in a bounded fluid layer

1992 ◽  
Vol 241 ◽  
pp. 587-614 ◽  
Author(s):  
T. Dracos ◽  
M. Giger ◽  
G. H. Jirka
Keyword(s):  
Experimental Investigation ◽  
Cross Section ◽  
Fluid Layer ◽  
Three Dimensional ◽  
Turbulent Jets ◽  
Two Dimensional ◽  
Vortical Structures ◽  
Secondary Currents ◽  
Fluid Layers ◽  
Bounding Surfaces

An experimental investigation of plane turbulent jets in bounded fluid layers is presented. The development of the jet is regular up to a distance from the orifice of approximately twice the depth of the fluid layer. From there on to a distance of about ten times the depth, the flow is dominated by secondary currents. The velocity distribution over a cross-section of the jet becomes three-dimensional and the jet undergoes a constriction in the midplane and a widening near the bounding surfaces. Beyond a distance of approximately ten times the depth of the bounded fluid layer the secondary currents disappear and the jet starts to meander around its centreplane. Large vortical structures develop with axes perpendicular to the bounding surfaces of the fluid layer. With increasing distance the size of these structures increases by pairing. These features of the jet are associated with the development of quasi two-dimensional turbulence. It is shown that the secondary currents and the meandering do not significantly affect the spreading of the jet. The quasi-two-dimensional turbulence, however, developing in the meandering jet, significantly influences the mixing of entrained fluid.

scholarly journals Derivation of Equations for a Size Distribution of Spherical Particles in Non-Transparent Materials

2021 ◽  
Vol 5 (4) ◽  
pp. 53-60
Author(s):  
Daniel Gurgul ◽  
Andriy Burbelko ◽  
Tomasz Wiktor
Keyword(s):  
Probability Density Function ◽  
Probability Density ◽  
Size Distribution ◽  
Density Function ◽  
Cross Section ◽  
Three Dimensional ◽  
Spherical Particles ◽  
Two Dimensional ◽  
Mathematical Formulas ◽  
Transparent Materials

This paper presents a new proposition on how to derive mathematical formulas that describe an unknown Probability Density Function (PDF3) of the spherical radii (r3) of particles randomly placed in non-transparent materials. We have presented two attempts here, both of which are based on data collected from a random planar cross-section passed through space containing three-dimensional nodules. The first attempt uses a Probability Density Function (PDF2) the form of which is experimentally obtained on the basis of a set containing two-dimensional radii (r2). These radii are produced by an intersection of the space by a random plane. In turn, the second solution also uses an experimentally obtained Probability Density Function (PDF1). But the form of PDF1 has been created on the basis of a set containing chord lengths collected from a cross-section.The most important finding presented in this paper is the conclusion that if the PDF1 has proportional scopes, the PDF3 must have a constant value in these scopes. This fact allows stating that there are no nodules in the sample space that have particular radii belonging to the proportional ranges the PDF1.

scholarly journals Membrane analogy for multi-material bars under torsion

2019 ◽  
Vol 475 (2225) ◽  
pp. 20190124 ◽  
Author(s):  
Laura Galuppi ◽  
Gianni Royer-Carfagni
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Elastic Problem ◽  
Two Dimensional ◽  
Torsion Problem ◽  
Linear Elastic ◽  
Physical Apparatus

Prandtl's membrane analogy for the torsion problem of prismatic homogeneous bars is extended to multi-material cross sections. The linear elastic problem is governed by the same equations describing the deformation of an inflated membrane, differently tensioned in regions that correspond to the domains hosting different materials in the bar cross section, in a way proportional to the inverse of the material shear modulus. Multi-connected cross sections correspond to materials with vanishing stiffness inside the holes, implying infinite tension in the corresponding portions of the membrane. To define the interface constrains that allow to apply such a state of prestress to the membrane, a physical apparatus is proposed, which can be numerically modelled with a two-dimensional mesh implementable in commercial finite-element model codes. This approach presents noteworthy advantages with respect to the three-dimensional modelling of the twisted bar.

Geometry Effects in Eulerian/Granular Simulation of a Turbulent FCC Riser with a (kg-?g)-KTGF Model

2010 ◽  
Vol 8 (1) ◽  
Author(s):  
Hamid Reza Nazif ◽  
Hassan Basirat Tabrizi ◽  
Farhad A Farhadpour
Keyword(s):  
Cross Section ◽  
Large Scale ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Good Prediction ◽  
Model Predictions ◽  
Secondary Circulations ◽  
Sharp Corners ◽  
Granular Simulation

Three-dimensional, transient turbulent particulate flow in an FCC riser is modeled using an Eulerian/Granular approach. The turbulence in the gas phase is described by a modified realizable (kg-?g) closure model and the kinetic theory of granular flow (KTGF) is employed for the particulate phase. Separate simulations are conducted for a rectangular and a cylindrical riser with similar dimensions. The model predictions are validated against experimental data of Sommerfeld et al (2002) and also compared with the previously reported LES-KTGF simulations of Hansen et al (2003) for the rectangular riser. The (kg-?g)-KTGF model does not perform as well as the LES-KTGF model for the riser with a rectangular cross section. This is because, unlike the more elaborate LES-KTGF model, the simpler (kg-?g)-KTGF model cannot capture the large scale secondary circulations induced by anisotropic turbulence at the corners of the rectangular riser. In the cylindrical geometry, however, the (kg-?g)-KTGF model gives good prediction of the data and is a viable alternative to the more complex LES-KTGF model. This is not surprising as the circulations in the riser with a circular cross section are due to the curvature of the walls and not due to the presence of sharp corners.

Sign in / Sign up

Export Citation Format

Share Document