scholarly journals Projected Changes in Soil Temperature and Surface Energy Budget Components over the Alps and Northern Italy

Water ◽  
2018 ◽  
Vol 10 (7) ◽  
pp. 954 ◽  
Author(s):  
Claudio Cassardo ◽  
Seon Park ◽  
Sungmin O ◽  
Marco Galli

This study investigates the potential changes in surface energy budget components under certain future climate conditions over the Alps and Northern Italy. The regional climate scenarios are obtained though the Regional Climate Model version 3 (RegCM3) runs, based on a reference climate (1961–1990) and the future climate (2071–2100) via the A2 and B2 scenarios. The energy budget components are calculated by employing the University of Torino model of land Processes Interaction with Atmosphere (UTOPIA), and using the RegCM3 outputs as input data. Our results depict a significant change in the energy budget components during springtime over high-mountain areas, whereas the most relevant difference over the plain areas is the increase in latent heat flux and hence, evapotranspiration during summertime. The precedence of snow-melting season over the Alps is evidenced by the earlier increase in sensible heat flux. The annual mean number of warm and cold days is evaluated by analyzing the top-layer soil temperature and shows a large increment (slight reduction) of warm (cold) days. These changes at the end of this century could influence the regional radiative properties and energy cycles and thus, exert significant impacts on human life and general infrastructures.

2014 ◽  
Vol 14 (18) ◽  
pp. 9481-9509 ◽  
Author(s):  
D. P. Grosvenor ◽  
J. C. King ◽  
T. W. Choularton ◽  
T. Lachlan-Cope

Abstract. Mesoscale model simulations are presented of a westerly föhn event over the Antarctic Peninsula mountain ridge and onto the Larsen C ice shelf, just south of the recently collapsed Larsen B ice shelf. Aircraft observations showed the presence of föhn jets descending near the ice shelf surface with maximum wind speeds at 250–350 m in height. Surface flux measurements suggested that melting was occurring. Simulated profiles of wind speed, temperature and wind direction were very similar to the observations. However, the good match only occurred at a model time corresponding to ~9 h before the aircraft observations were made since the model föhn jets died down after this. This was despite the fact that the model was nudged towards analysis for heights greater than ~1.15 km above the surface. Timing issues aside, the otherwise good comparison between the model and observations gave confidence that the model flow structure was similar to that in reality. Details of the model jet structure are explored and discussed and are found to have ramifications for the placement of automatic weather station (AWS) stations on the ice shelf in order to detect föhn flow. Cross sections of the flow are also examined and were found to compare well to the aircraft measurements. Gravity wave breaking above the mountain crest likely created a~situation similar to hydraulic flow and allowed föhn flow and ice shelf surface warming to occur despite strong upwind blocking, which in previous studies of this region has generally not been considered. Our results therefore suggest that reduced upwind blocking, due to wind speed increases or stability decreases, might not result in an increased likelihood of föhn events over the Antarctic Peninsula, as previously suggested. The surface energy budget of the model during the melting periods showed that the net downwelling short-wave surface flux was the largest contributor to the melting energy, indicating that the cloud clearing effect of föhn events is likely to be the most important factor for increased melting relative to non-föhn days. The results also indicate that the warmth of the föhn jets through sensible heat flux ("SH") may not be critical in causing melting beyond boundary layer stabilisation effects (which may help to prevent cloud cover and suppress loss of heat by convection) and are actually cancelled by latent heat flux ("LH") effects (snow ablation). It was found that ground heat flux ("GRD") was likely to be an important factor when considering the changing surface energy budget for the southern regions of the ice shelf as the climate warms.


2014 ◽  
Vol 55 (66) ◽  
pp. 111-120 ◽  
Author(s):  
Weijun Sun ◽  
Xiang Qin ◽  
Wentao Du ◽  
Weigang Liu ◽  
Yushuo Liu ◽  
...  

AbstractGlacier surface melting can be described using energy-balance models. We conducted a surface energy budget experiment to quantify surface energy fluxes and to identify factors affecting glacial melt in the ablation zone of Laohugou glacier No. 12, western Qilian mountains. The surface energy budget was calculated based on data from an automatic weather station, and turbulent fluxes calculated using the bulk-aerodynamic approach were corrected using measurements from an eddy-covariance system. Simulated mass balances were validated by stake observations. Net shortwave radiation was the primary component of the surface energy balance (126Wm–2), followed by sensible heat flux. Net longwave radiation (–45Wm–2) and latent heat flux (–12.8 Wm–2) represented heat sinks. The bulk-aerodynamic method underestimated sensible and latent heat fluxes by 3.4 and 1.2 W m–2, respectively. The simulated total mass balance of –1703mmw.e. exceeded the observed total by 90 mm w.e. Daily positive accumulated temperature and low albedo were the main factors accelerating glacier melt. An uncertainty assessment showed that mass balance was very sensitive to albedo and varied by 36% when albedo changed by 0.1.


2014 ◽  
Vol 14 (5) ◽  
pp. 5771-5835
Author(s):  
D. P. Grosvenor ◽  
J. C. King ◽  
T. W. Choularton ◽  
T. Lachlan-Cope

Abstract. Mesoscale model simulations are presented of a westerly föhn event over the Antarctic Peninsula mountain ridge and onto the Larsen C Ice Shelf, just south of the recently collapsed Larsen B Ice Shelf. Aircraft observations showed the presence of föhn jets descending near to the ice shelf surface with maximum wind speeds at 250–350 m in height. Surface flux measurements suggested that melting was occurring. Simulated profiles of wind speed, temperature and wind direction were very similar to the observations. However, the good match only occurred at a model time corresponding to ∼9 h before the aircraft observations were made since the model föhn jets died down after this. Through comparison to an Automatic Weather Station (AWS) on the ice shelf surface (east side of the ridge) this was attributed to problems with the time evolution of the large scale meteorology of the analysis used to nudge the upper levels of the model. Timing issues aside, the otherwise good comparison between the model and observations gave confidence that the model flow structure was similar to that in reality. Details of the model jet structure are explored and discussed and are found to have ramifications for the placement of AWS stations on the ice shelf in order to detect föhn flow. Cross sections of the flow are also examined and were found to compare well to the aircraft measurements. Gravity wave breaking above the mountain crest likely created a situation similar to hydraulic flow and allowed föhn flow and ice shelf surface warming to occur despite strong upwind blocking, which in previous studies of this region has generally not been considered. The surface energy budget of the model during the melting periods showed that the net downwelling shortwave surface flux was the largest contributor to the melting energy, indicating that the cloud clearing effect of föhn events is likely to be the most important factor for increased melting relative to non-föhn days. The results also indicate that the warmth of the föhn jets through sensible heat flux may not be critical in causing melting beyond boundary layer stabilization effects (which may help to prevent cloud cover and suppress loss of heat by convection) and are actually cancelled by latent heat flux effects (snow ablation). It was found that ground heat flux was likely to be an important factor when considering the changing surface energy budget for the southern regions of the ice shelf as the climate warms.


2009 ◽  
Vol 3 (2) ◽  
pp. 245-263 ◽  
Author(s):  
S. Westermann ◽  
J. Lüers ◽  
M. Langer ◽  
K. Piel ◽  
J. Boike

Abstract. Independent measurements of radiation, sensible and latent heat fluxes and the ground heat flux are used to describe the annual cycle of the surface energy budget at a high-arctic permafrost site on Svalbard. During summer, the net short-wave radiation is the dominant energy source, while well developed turbulent processes and the heat flux in the ground lead to a cooling of the surface. About 15% of the net radiation is consumed by the seasonal thawing of the active layer in July and August. The Bowen ratio is found to vary between 0.25 and 2, depending on water content of the uppermost soil layer. During the polar night in winter, the net long-wave radiation is the dominant energy loss channel for the surface, which is mainly compensated by the sensible heat flux and, to a lesser extent, by the ground heat flux, which originates from the refreezing of the active layer. The average annual sensible heat flux of −6.9 Wm−2 is composed of strong positive fluxes in July and August, while negative fluxes dominate during the rest of the year. With 6.8 Wm−2, the latent heat flux more or less compensates the sensible heat flux in the annual average. Strong evaporation occurs during the snow melt period and particularly during the snow-free period in summer and fall. When the ground is covered by snow, latent heat fluxes through sublimation of snow are recorded, but are insignificant for the average surface energy budget. The near-surface atmospheric stratification is found to be predominantly unstable to neutral, when the ground is snow-free, and stable to neutral for snow-covered ground. Due to long-lasting near-surface inversions in winter, an average temperature difference of approximately 3 K exists between the air temperature at 10 m height and the surface temperature of the snow. As such comprehensive data sets are sparse for the Arctic, they are of great value to improve process understanding and support modeling efforts on the present-day and future arctic climate and permafrost conditions.


2009 ◽  
Vol 3 (2) ◽  
pp. 631-680 ◽  
Author(s):  
S. Westermann ◽  
J. Lüers ◽  
M. Langer ◽  
K. Piel ◽  
J. Boike

Abstract. Independent measurements of radiation, sensible and latent heat fluxes and the ground heat flux are used to describe the annual cycle of the surface energy budget at a high-arctic permafrost site on Svalbard. During summer, the net short-wave radiation is the dominant energy source, while well developed turbulent processes and the heat flux in the ground lead to a cooling of the surface. About 15% of the net radiation is consumed by the seasonal thawing of the active layer in July and August. The Bowen ratio is found to vary between 0.25 and 2, depending on water content of the uppermost soil layer. During the polar night in winter, the net long-wave radiation is the dominant energy loss channel for the surface, which is mainly compensated by the sensible heat flux and, to a lesser extent, by the ground heat flux, which originates from the refreezing of the active layer. The average annual sensible heat flux of −6.9 Wm−2 is composed of strong positive fluxes in July and August, while negative fluxes dominate during the rest of the year. With 6.8 Wm−2, the latent heat flux more or less compensates the sensible heat flux in the annual average. Strong evaporation occurs during the snow melt period and particularly during the snow-free period in summer and fall. When the ground is covered by snow, latent heat fluxes through sublimation of snow are recorded, but are insignificant for the average surface energy budget. The near-surface atmospheric stratification is found to be predominantly unstable to neutral, when the ground is snow-free, and stable to neutral for snow-covered ground. Due to long-lasting near-surface inversions in winter, an average temperature difference of approximately 3 K exists between the air temperature at 10 m height and the surface temperature of the snow.


2019 ◽  
Vol 32 (3) ◽  
pp. 769-789 ◽  
Author(s):  
Michael Tjernström ◽  
Matthew D. Shupe ◽  
Ian M. Brooks ◽  
Peggy Achtert ◽  
John Prytherch ◽  
...  

During the Arctic Clouds in Summer Experiment (ACSE) in summer 2014 a weeklong period of warm-air advection over melting sea ice, with the formation of a strong surface temperature inversion and dense fog, was observed. Based on an analysis of the surface energy budget, we formulated the hypothesis that, because of the airmass transformation, additional surface heating occurs during warm-air intrusions in a zone near the ice edge. To test this hypothesis, we explore all cases with surface inversions occurring during ACSE and then characterize the inversions in detail. We find that they always occur with advection from the south and are associated with subsidence. Analyzing only inversion cases over sea ice, we find two categories: one with increasing moisture in the inversion and one with constant or decreasing moisture with height. During surface inversions with increasing moisture with height, an extra 10–25 W m−2 of surface heating was observed, compared to cases without surface inversions; the surface turbulent heat flux was the largest single term. Cases with less moisture in the inversion were often cloud free and the extra solar radiation plus the turbulent surface heat flux caused by the inversion was roughly balanced by the loss of net longwave radiation.


Atmosphere ◽  
2020 ◽  
Vol 11 (8) ◽  
pp. 877
Author(s):  
Klára Ambrožová ◽  
Filip Hrbáček ◽  
Kamil Láska

Despite the key role of the surface energy budget in the global climate system, such investigations are rare in Antarctica. In this study, the surface energy budget measurements from the largest ice-free area on northern James Ross Island, in Antarctica, were obtained. The components of net radiation were measured by a net radiometer, while sensible heat flux was measured by a sonic anemometer and ground heat flux by heat flux plates. The surface energy budget was compared with the rest of the Antarctic Peninsula Region and selected places in the Arctic and the impact of surface energy budget components on the ground thermal regime was examined. Mean net radiation on James Ross Island during January–March 2018 reached 102.5 W m−2. The main surface energy budget component was the latent heat flux, while the sensible heat flux values were only 0.4 W m−2 lower. Mean ground heat flux was only 0.4 Wm-2, however, it was negative in 47% of January–March 2018, while it was positive in the rest of the time. The ground thermal regime was affected by surface energy budget components to a depth of 50 cm. The strongest relationship was found between ground heat flux and ground surface temperature. Further analysis confirmed that active layer refroze after a sequence of three days with negative ground heat flux even in summer months. Daily mean net radiation and ground heat flux were significantly reduced when cloud amount increased, while the influence of snow cover on ground surface temperature was negligible.


2014 ◽  
Vol 53 (9) ◽  
pp. 2114-2129 ◽  
Author(s):  
Prathap Ramamurthy ◽  
Elie Bou-Zeid ◽  
James A. Smith ◽  
Zhihua Wang ◽  
Mary L. Baeck ◽  
...  

AbstractUrban facets—the walls, roofs, and ground in built-up terrain—are often conceptualized as homogeneous surfaces, despite the obvious variability in the composition and material properties of the urban fabric at the subfacet scale. This study focuses on understanding the influence of this subfacet heterogeneity, and the associated influence of different material properties, on the urban surface energy budget. The Princeton Urban Canopy Model, which was developed with the ability to capture subfacet variability, is evaluated at sites of various building densities and then applied to simulate the energy exchanges of each subfacet with the atmosphere over a densely built site. The analyses show that, although all impervious built surfaces convert most of the incoming energy into sensible heat rather than latent heat, sensible heat fluxes from asphalt pavements and dark rooftops are 2 times as high as those from concrete surfaces and light-colored roofs. Another important characteristic of urban areas—the shift in the peak time of sensible heat flux in comparison with rural areas—is here shown to be mainly linked to concrete’s high heat storage capacity as well as to radiative trapping in the urban canyon. The results also illustrate that the vegetated pervious soil surfaces that dot the urban landscape play a dual role: during wet periods they redistribute much of the available energy into evaporative fluxes but when moisture stressed they behave more like an impervious surface. This role reversal, along with the direct evaporation of water stored over impervious surfaces, significantly reduces the overall Bowen ratio of the urban site after rain events.


Sign in / Sign up

Export Citation Format

Share Document