scholarly journals Finite Element Analysis of Wind Turbine Blade Vibrations

Vibration ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 310-322
Author(s):  
Navid Navadeh ◽  
Ivan Goroshko ◽  
Yaroslav Zhuk ◽  
F. Etminan Moghadam ◽  
Arash S. Fallah
Keyword(s):  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Reaction Force ◽  
Wind Farms ◽  
Element Model ◽  
Rotor Blades ◽  
Horizontal Axis Wind Turbine ◽  
Element Analysis ◽  
Blade Vibrations

The article is devoted to the practical problem of computer simulation of the dynamic behaviour of horizontal axis wind turbine composite rotor blades. This type of wind turbine is the dominant design in modern wind farms, and as such its dynamics and strength characteristics should be carefully studied. For this purpose, in this paper the mechanical model of a rotor blade with a composite skin possessing a stiffener was developed and implemented as a finite element model in ABAQUS. On the basis of this computer model, modal analysis of turbine blade vibrations was performed and benchmark cases for the dynamic response were investigated. The response of the system subjected to a uniform underneath pressure was studied, and the root reaction force and blade tip displacement time histories were obtained from the numerical calculations conducted.

Finite Element Analysis of 5MW Fiberglass and Carbon Fiber Wind Turbine Blade

2011 ◽  
Vol 418-420 ◽  
pp. 606-609 ◽  
Author(s):  
Tian De ◽  
Guang Hua Chen ◽  
Jian Mei Zhang
Keyword(s):  
Finite Element ◽  
Carbon Fiber ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Limit Load ◽  
Element Model ◽  
Wind Turbine Blade ◽  
Horizontal Axis Wind Turbine ◽  
Element Analysis

Abstract: Base on finite element method of composite, take 5MW horizontal axis wind turbine blades as example, skin uses a mixture of fiberglass and carbon fiber as ply, spar caps and web adopt carbon fiber ply entirely to build the finite element model of the blade. The total weigh of the blade is 20.2 ton. Use Bladed software calculated the limit load of each cross-section, analyzed the stress distribution of each section and the modal characteristics of the blade, these provide a theoretical reference for the application of carbon fiber using on MW class wind turbine blade.

Strength Evaluation and Failure Prediction of a Composite Wind Turbine Blade Using Finite Element Analysis

2010 ◽  
Author(s):  
Prenil Poulose ◽  
Zhong Hu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Failure Prediction ◽  
Element Model ◽  
Wind Turbine Blade ◽  
Element Analysis ◽  
Strength Evaluation

Strength evaluation and failure prediction on a modern composite wind turbine blade have been conducted using finite element analysis. A 3-dimensional finite element model has been developed. Stresses and deflections in the blade under extreme storm conditions have been investigated for different materials. The conventional wood design turbine blade has been compared with the advanced E-glass fiber and Carbon epoxy composite blades. Strength has been analyzed and compared for blades with different laminated layer stacking sequences and fiber orientations for a composite material. Safety design and failure prediction have been conducted based on the different failure criteria. The simulation error estimation has been evaluated. Simulation results have shown that finite element analysis is crucial for designing and optimizing composite wind turbine blades.

Finite Element Analysis of Large Diameter Grouted Connections

2007 ◽  
Author(s):  
Lars P. Nielsen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Large Diameter ◽  
Wind Farms ◽  
Element Model ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Joint Research ◽  
Element Analysis

When considering offshore monopile foundations designed for wind turbine support structures, a grouted connection between the monopile and an overlapping transition piece has become the de facto standard. These connections rely on axial loads being carried primarily by the bond between the steel and grout as shear. Given the critical nature of the grouted connection in a system with zero redundancy, the current design verification requirement is that a finite element analysis is performed to ascertain the viability of the connection with respect to combined axial and bending capacity whilst pure axial capacity is handled as a decoupled phenomenon using simple analytical formulas. The present paper addresses the practical modeling aspects of such a finite element model, covering subjects such as constitutive formulations for the grout, mesh density, and steel/grout interaction. The aim of the paper is to discuss different modeling approaches and, to the extent possible, provide basic guidelines for the minimum requirements valid for this type of analysis. This discussion is based on the accumulated experience gained though the independent verification of more than 10 currently operational offshore wind farms that have been certified by DNV, as well as the significant joint research and development with industry captured in the DNV Offshore Standard for Design of Offshore Wind Turbine Structures DNV-OS-J101. Moreover, general observations relating to the basic subjects such as overall geometric extent of the model, inclusion of secondary structures, detail simplification, boundary conditions, load application etc. are presented based on the authors more than 3 year involvement on the subject at DNV.

The Finite Element Analysis of the Large Horizontal Axis Wind Turbine Generator Tower

2013 ◽  
Vol 444-445 ◽  
pp. 836-840
Author(s):  
Wei Chen ◽  
Shi Yue Wang ◽  
Liang Cao ◽  
Hui Ming Wang ◽  
Ji Yao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Natural Frequencies ◽  
Element Model ◽  
Horizontal Axis Wind Turbine ◽  
Maximum Displacement ◽  
Element Analysis ◽  
Wind Turbine Tower ◽  
Modes Of Vibration

Building finite element model of wind turbine tower, analyzing Static and modal of tower with using finite element analysis software ANSYS .Getting stress distribution, maximum displacement, natural frequencies and modes of vibration by finite element modal analysis of wind turbine tower and analyzing natural frequencies of wind turbine tower to determine whether to cause the tower and the wind wheel drive resonance.

Finite Element Analysis of Large-Size Yaw Bearings with Supporting Structure in Wind Turbine

2014 ◽  
Vol 672-674 ◽  
pp. 1550-1553
Author(s):  
Zhen Guo Shang ◽  
Zhong Chao Ma ◽  
Zhen Sheng Sun
Keyword(s):  
Finite Element ◽  
Wind Turbine ◽  
Point Contact ◽  
Element Model ◽  
Contact Forces ◽  
Element Analysis ◽  
Supporting Structure ◽  
Rolling Elements ◽  
Yaw Bearing ◽  
Compression Springs

A procedure for obtaining the load distribution in a four point contact wind turbine yaw bearing considering the effect of the structure’s elasticity is presented. The inhomogeneous stiffness of the supporting structures creates a variation in the results obtained with a rigid model. A finite element model substituting the rolling elements with nonlinear compression springs has been built to evaluate the effect of the supporting structure elasticity on the contact forces between the rolling elements and the raceways.

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

A Finite Element Analysis of the Human Temporomandibular Joint

1994 ◽  
Vol 116 (4) ◽  
pp. 401-407 ◽  
Author(s):  
J. Chen ◽  
Liangfeng Xu
Keyword(s):  
Finite Element ◽  
Temporomandibular Joint ◽  
Reaction Force ◽  
Element Model ◽  
Contact Stresses ◽  
Element Analysis ◽  
Tensile Stresses ◽  
Reaction Forces ◽  
Von Mises ◽  
Von Mises Stresses

A 2-D finite element model of the human temporomandibular joint (TMJ) has been developed to investigate the stresses and reaction forces within the joint during normal sagittal jaw closure. The mechanical parameters analyzed were maximum principal and von Mises stresses in the disk, the contact stresses on the condylar and temporal surfaces, and the condylar reactions. The model bypassed the complexity of estimating muscle forces by using measured joint motion as input. The model was evaluated by several tests. The results demonstrated that the resultant condylar reaction force was directed toward the posterior side of the eminence. The contact stresses along the condylar and temporal surfaces were not evenly distributed. Separations were found at both upper and lower boundaries. High tensile stresses were found at the upper boundaries. High tensile stresses were found at the upper boundary of the middle portion of the disk.

scholarly journals Dynamic Analysis of Tapered Thin-Walled Beams Using Spectral Finite Element Method

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Yiping Shen ◽  
Zhijun Zhu ◽  
Songlai Wang ◽  
Gang Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Wind Turbine ◽  
Element Model ◽  
Rotor Blades ◽  
Mode Shapes ◽  
Modal Frequency ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Spectral Finite Element

Tapered thin-walled structures have been widely used in wind turbine and rotor blade. In this paper, a spectral finite element model is developed to investigate tapered thin-walled beam structures, in which torsion related warping effect is included. First, a set of fully coupled governing equations are derived using Hamilton’s principle to account for axial, bending, and torsion motion. Then, the differential transform method (DTM) is applied to obtain the semianalytical solutions in order to formulate the spectral finite element. Finally, numerical simulations are conducted for tapered thin-walled wind turbine rotor blades and validated by the ANSYS. Modal frequency results agree well with the ANSYS predictions, in which approximate 30,000 shell elements were used. In the SFEM, one single spectral finite element is needed to perform such calculations because the interpolation functions are deduced from the exact semianalytical solutions. Coupled axial-bending-torsion mode shapes are obtained as well. In summary, the proposed spectral finite element model is able to accurately and efficiently to perform the modal analysis for tapered thin-walled rotor blades. These modal frequency and mode shape results are important to carry out design and performance evaluation of the tapered thin-walled structures.

Sign in / Sign up

Export Citation Format

Share Document