scholarly journals The Promise of Turning Induced Deformation Process for Synthesizing Magnesium Based Materials with Superior Mechanical Response

Technologies ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 69
Author(s):  
Michael Johanes ◽  
Manoj Gupta
Keyword(s):  
Mechanical Response ◽  
Cutting Speed ◽  
Hot Extrusion ◽  
Positive Influence ◽  
Economic Benefits ◽  
Processing Method ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
High Depth ◽  
Significant Positive Influence

In recent times, an alternative synthesis pathway involving severe plastic deformation for Mg-based materials has been explored involving the generation of turnings according to a set of machining parameters and cold compaction into billets followed by hot extrusion. This is known as the turning induced deformation (TID) method and has shown potential to alter the properties of resulting Mg-based materials for the better, not to mention economic benefits arising from this processing method. This work summarizes exploratory efforts involving this method for synthesis of Mg-based materials. The TID method resulted in overall superior properties compared to conventional processing methods, while two distinct parameters (high depth of cut and low cutting speed) were found to have significant positive influence on the final material properties, and as such are considered to be suitable basis on which further exploratory work in this field may be conducted.

Multiresponse Optimization of Al Alloy-SiC Composite Machining Parameters for Minimum Tool Wear and Maximum Metal Removal Rate

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Rajesh Kumar Bhushan
Keyword(s):  
Tool Wear ◽  
Metal Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Al Alloy ◽  
Machining Parameters ◽  
Metal Removal Rate ◽  
Nose Radius ◽  
Multiresponse Optimization

Optimization in turning means determination of the optimal set of the machining parameters to satisfy the objectives within the operational constraints. These objectives may be the minimum tool wear, the maximum metal removal rate (MRR), or any weighted combination of both. The main machining parameters which are considered as variables of the optimization are the cutting speed, feed rate, depth of cut, and nose radius. The optimum set of these four input parameters is determined for a particular job-tool combination of 7075Al alloy-15 wt. % SiC (20–40 μm) composite and tungsten carbide tool during a single-pass turning which minimizes the tool wear and maximizes the metal removal rate. The regression models, developed for the minimum tool wear and the maximum MRR were used for finding the multiresponse optimization solutions. To obtain a trade-off between the tool wear and MRR the, a method for simultaneous optimization of the multiple responses based on an overall desirability function was used. The research deals with the optimization of multiple surface roughness parameters along with MRR in search of an optimal parametric combination (favorable process environment) capable of producing desired surface quality of the turned product in a relatively lesser time (enhancement in productivity). The multi-objective optimization resulted in a cutting speed of 210 m/min, a feed of 0.16 mm/rev, a depth of cut of 0.42 mm, and a nose radius of 0.40 mm. These machining conditions are expected to respond with the minimum tool wear and maximum the MRR, which correspond to a satisfactory overall desirability.

Manufacture of Microcantilever Sensors

2005 ◽  
Author(s):  
Andrew W. McFarland ◽  
Jonathan S. Colton ◽  
Daniel Cox ◽  
Steven Y. Liang
Keyword(s):  
Machine Tool ◽  
Mechanical Response ◽  
Surface Force ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Machining Parameters ◽  
Form Accuracy ◽  
Microcantilever Sensors ◽  
Micro Scale ◽  
Sensing Applications

Mechanical micro machining is an emerging technology with many potential benefits and equally great challenges. The push to develop processes and tools capable of micro scale fabrication is a result of the widespread drive to reduce part and feature size. One important factor that contributes to the ability to machine at the microscale level is the overall size of the machine tool due to the effects of thermal, static, and dynamic stabilities. This paper explores the technical feasibility of miniaturized machine tools capable of fabricating features and parts on the micro scale in terms of depth of cut and part form accuracy. It develops a machine tool and examines its capabilities through benchmarking tests and the making of precision dies for the injection molding of microcantilever parts. The design and configuration of a miniaturized vertical machining center of overall dimension less than 300 mm on a side is presented and the component specifications discussed. The six axis machine has linear positioning resolution of 4 nm by 10 nm by 10 nm, with accuracy on the order of 0.3 μm, in the height, feed, and cross feed directions. The work volume as defined by the ranges of axes travel are 4 mm by 25 mm by 25 mm in the height, feed, and cross feed and 20 degrees in the rotational space. To quantify the performance capability of the miniaturized machine tool as a system, a series of evaluation tests were implemented based on linear and arch trajectories over a range of feed speed and depth of cut conditions. Test results suggest that micro level form accuracy and sub-micron level finish are generally achievable for parts with moderate curvature and gradient in the geometry under selected machining parameters and conditions. An injection mold was made of steel with this machine and plastic microcantilevers fabricated. Plastic microcantilevers are appropriate for sensing applications such as surface probe microscopy. The microcantilevers, made from polystyrene, were 464 to 755 μm long, 130 μm wide and only 6–9 μm thick. They showed very good uniformity, reproducibility, and appropriate mechanical response for use as sensors in surface force microscopy.

Micro Textured Cutting Inserts with Solid Lubrication as Alternative Coolant to Mineral Oil-Based Cutting Fluid in Turning Operation

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
C. Divya ◽  
L. Suvarna Raju ◽  
B. Singaravel
Keyword(s):  
Process Parameters ◽  
Orthogonal Array ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Solid Lubricants ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process ◽  
Optimization Of Process Parameters ◽  
Cutting Inserts

Turning process is a primary process in engineering industries and optimization of process parameters enhance the machining performance. Inconel 718 is a nickel-based superalloy, widely found applications in the manufacturing of blades, sheets and discs in aircraft engines and rocket engines. It provides toughness at low temperature, with stand high mechanical stresses at elevated temperature and creep resistance. In this work, turning process is carried out on Inconel 718 with micro whole textured cutting inserts filled with solid lubricants. Three different solid lubricants are used namely molybdenum-di-sulfide (MoS2), tungsten-di-sulfide (WS2) and calcium-di-fluoride (CaF2). Experiments are performed as per L9 orthogonal array. Statistical approaches such as orthogonal array, Signal-to-Noise (S/N) ratio and Analysis of Variance (ANOVA) are used to find the importance and effects of machining parameters. In this study, input parameters included are feed, cutting speed and depth of cut and output parameter includes surface roughness. Optimization of process parameters is carried out and the significance is estimated. The result suggested that WS2 followed by MoS2 and CaF2 given good surface finish value. Also, solid lubricant in machining enhances the sustainability in manufacturing.

scholarly journals Investigation of AlCrN-Coated Inserts on Cryogenic Turning of Ti-6Al-4V Alloy

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1338
Author(s):  
Lakshmanan Selvam ◽  
Pradeep Kumar Murugesan ◽  
Dhananchezian Mani ◽  
Yuvaraj Natarajan
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Physical Vapor Deposition ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Coated Carbide ◽  
Cryogenic Conditions

Over the past decade, the focus of the metal cutting industry has been on the improvement of tool life for achieving higher productivity and better finish. Researchers are attempting to reduce tool failure in several ways such as modified coating characteristics of a cutting tool, conventional coolant, cryogenic coolant, and cryogenic treated insert. In this study, a single layer coating was made on cutting carbide inserts with newly determined thickness. Coating thickness, presence of coating materials, and coated insert hardness were observed. This investigation also dealt with the effect of machining parameters on the cutting force, surface finish, and tool wear when turning Ti-6Al-4V alloy without coating and Physical Vapor Deposition (PVD)-AlCrN coated carbide cutting inserts under cryogenic conditions. The experimental results showed that AlCrN-based coated tools with cryogenic conditions developed reduced tool wear and surface roughness on the machined surface, and cutting force reductions were observed when a comparison was made with the uncoated carbide insert. The best optimal parameters of a cutting speed (Vc) of 215 m/min, feed rate (f) of 0.102 mm/rev, and depth of cut (doc) of 0.5 mm are recommended for turning titanium alloy using the multi-response TOPSIS technique.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

scholarly journals Optimization of machining parameters in face milling using multi-objective Taguchi technique

2018 ◽  
Vol 12 (2) ◽  
pp. 104-108 ◽  
Author(s):  
Yusuf Fedai ◽  
Hediye Kirli Akin
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Taguchi Technique ◽  
Average Roughness ◽  
Multi Objective ◽  
Control Factors ◽  
Average Maximum

In this research, the effect of machining parameters on the various surface roughness characteristics (arithmetic average roughness (Ra), root mean square average roughness (Rq) and average maximum height of the profile (Rz)) in the milling of AISI 4140 steel were experimentally investigated. Depth of cut, feed rate, cutting speed and the number of insert were considered as control factors; Ra, Rz and Rq were considered as response factors. Experiments were designed considering Taguchi L9 orthogonal array. Multi signal-to-noise ratio was calculated for the response variables simultaneously. Analysis of variance was conducted to detect the significance of control factors on responses. Moreover, the percent contributions of the control factors on the surface roughness were obtained to be the number of insert (71.89 %), feed (19.74 %), cutting speed (5.08%) and depth of cut (3.29 %). Minimum surface roughness values for Ra, Rz and Rq were obtained at 325 m/min cutting speed, 0.08 mm/rev feed rate, 1 number of insert and 1 mm depth of cut by using multi-objective Taguchi technique.

scholarly journals Prediction of Machining Characteristics of Hybrid Composites Using Response Surface Methodology Approach

2018 ◽  
Vol 7 (3.1) ◽  
pp. 162 ◽  
Author(s):  
Ramanan. G ◽  
Rajesh Prabha.N ◽  
Diju Samuel.G ◽  
Jai Aultrin. K. S ◽  
M Ramachandran
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Hybrid Composites ◽  
Removal Rate ◽  
Cutting Speed ◽  
Chemical Properties ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Optimal Parameters ◽  
Rsm Technique

This manuscript presents the influencing parameters of CNC turning conditions to get high removal rate and minimal response of surface roughness in turning of AA7075-TiC-MoS2 composite by response surface method. These composites are particularly suited for applications that require higher strength, dimensional stability and enhanced structural rigidity. Composite materials are engineered materials made from at least two or more constituent materials having different physical or chemical properties. In this work seventeen turning experiments were conducted using response surface methodology. The machining parameters cutting speed, feed rate, and depth of cut are varied with respect to different machining conditions for each run. The optimal parameters were predicted by RSM technique. Turning process is studied by response surface methodology design of experiment. The optimal parameters were predicted by RSM technique. The most influencing process parameter predicted from RSM techniques in cutting speed and depth of cut.   

Finite Element Simulation of Precision Cutting Monocrystalline Silicon

2013 ◽  
Vol 662 ◽  
pp. 99-102 ◽  
Author(s):  
Li Qiu Shi ◽  
Xiao Wen Li ◽  
Feng Yu
Keyword(s):  
High Surface ◽  
Cutting Speed ◽  
Monocrystalline Silicon ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Tool Edge Radius ◽  
Transition Mechanism ◽  
Edge Radius ◽  
Tool Edge ◽  
Optimization Of Cutting Parameters

Monocrystalline silicon is typical of hard brittle materials, a high surface quality can be obtained in ductile-regime cutting. The success of the turning process depends on optimizing the machining parameters such as the tool edge radius, tool rake angles, depth of cut and cutting speed, etc. In this study, based on the ductile–brittle transition mechanism, the optimization of cutting parameters were determined with the commercial, general purpose FEA software Msc.Marc. The result demonstrates that the value of temperature is minimum when the tool rake angle is in the range of -15º～-30º. Smaller tool edge radius was selected while maintaining quality of tool edge radius and tool life. As long as beyond the range of cutting speed 6 ~ 8 mm/s, smaller residual stress can be obtain.

Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method

2012 ◽  
Vol 227 (9) ◽  
pp. 1889-1897 ◽  
Author(s):  
R Thirumalai ◽  
JS Senthilkumaar ◽  
P Selvarani ◽  
S Ramesh
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Flank Wear ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Parameters ◽  
Dry Machining ◽  
Noise Factors

Extensive researchers have conducted several experiments in the past for selecting the optimum parameters in machining nickel based alloy – Inconel 718. These experiments conducted so far are dealt with dry machining and flooded coolant machining of nickel alloy Inconel 718. In this research study, the usage of refrigerated coolant is also dealt with and it is compared with dry machining and flooded coolant machining. Cutting speed, feed and depth of cut are considered as the machining parameters. The effectiveness of the refrigerated coolant in machining the heat resistant super alloy material Inconel 718 with respect to these machining parameters are described in this article. The machinability studies parameters were generated with surface roughness and flank wear. The performance of uncoated carbide cutting tool was investigated at various cutting condition under dry, flooded coolant and refrigerated coolant machining. The relationship between the machining parameters and the performance measures were established and using analysis of variance significant machining parameters determined. This article made an attempt to Taguchi optimization technique to study the machinability performances of Inconel 718. Taguchi approach is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer experiments than a factorial design. Taguchi’s optimization analysis indicates that the factors level, its significance to influence the surface roughness and flank wear for the machining processes. Confirmation tests were conducted at an optimal condition to make a comparison between the experimental results foreseen from the mentioned correlations.

Sign in / Sign up

Export Citation Format

Share Document