scholarly journals A Maximum Power Point Tracking Algorithm of Load Current Maximization-Perturbation and Observation Method with Variable Step Size

Symmetry ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 244
Author(s):  
Lieping Zhang ◽  
Zhengzhong Wang ◽  
Peng Cao ◽  
Shenglan Zhang
Keyword(s):  
Photovoltaic Cell ◽  
Maximum Power ◽  
Variable Step Size ◽  
Step Size ◽  
Maximum Power Point ◽  
Load Current ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Variable Step ◽  
Power Point

A photovoltaic power supply with a simple structure and high tracking efficiency is needed in self-powered, wireless sensor networks. First, a maximum power point tracking (MPPT) algorithm, including the load current maximization-perturbation and observation (LCM-P&O) methods, with a fixed step size, is proposed by integrating the traditional load current maximization (LCM) method and perturbation and observation (P&O) method. By sampling the changes of load current and photovoltaic cell input current once the disturbance is applied, the pulse width modulation (PWM) regulation mode, i.e., increasing or reducing, can be determined in the next process. Then, the above algorithm is improved by using the variable step size strategy. By comparing the difference between the absolute value of the observed current value and the theoretical current value at the maximum power point of the photovoltaic cell with the set threshold value, the variable step size for perturbation is determined. MATLAB simulation results show that the LCM-P&O method, with a variable step size, has faster convergence speed and higher tracking accuracy. Finally, the two MPPT algorithms are tested and analyzed under constant voltage source input and indoor fluorescent lamp illumination through an actual circuit, respectively. The experimental results show that the LCM-P&O method with variable step size has a higher tracking efficiency, about 90%–92%, and has higher stability and lower power consumption.

Implementation in Arduino of MPPT Using Variable Step Size P&O Algorithm in PV Installations

2017 ◽  
Vol 8 (1) ◽  
pp. 434 ◽  
Author(s):  
Mustapha Elyaqouti ◽  
Safa Hakim ◽  
Sadik Farhat ◽  
Lahoussine Bouhouch ◽  
Ahmed Ihlal
Keyword(s):  
Electric Energy ◽  
Maximum Power ◽  
Variable Step Size ◽  
Step Size ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Perturb And Observe ◽  
Variable Step ◽  
Power Point

In order to maximize the electric energy production of a photovoltaic generator (PVG), the maximum power point tracking (MPPT) methods are usually used in photovoltaic systems. The principle of these techniques is to operate the PVG to the maximum power point (MPP), which depends on the environmental factors, such as solar irradiance and ambient temperature, ensuring the optimal power transfer between PVG and load. In this paper, we present the implementation of two digital MPPT commands using the Arduino Mega type. The two proposed MPPT controls are based on the algorithm of perturb and observe (P&O), the first one with fixed perturbation step and the second one with two perturbations step varying with some conditions. The experimental results show that the P&O algorithm with variable step perturbation gives good results compared to the P&O algorithm with fixed perturbation step in terms of the time response and the oscillations around the MPP.

scholarly journals Advanced MPPT Algorithm for Distributed Photovoltaic Systems

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3576 ◽  
Author(s):  
Hyeon-Seok Lee ◽  
Jae-Jung Yun
Keyword(s):  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Variable Step Size ◽  
Step Size ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Tracking Algorithms ◽  
Variable Step ◽  
Power Point

The basic and adaptive maximum power point tracking algorithms have been studied for distributed photovoltaic systems to maximize the energy production of a photovoltaic (PV) module. However, the basic maximum power point tracking algorithms using a fixed step size, such as perturb and observe and incremental conductance, suffer from a trade-off between tracking accuracy and tracking speed. Although the adaptive maximum power point tracking algorithms using a variable step size improve the maximum power point tracking efficiency and dynamic response of the basic algorithms, these algorithms still have the oscillations at the maximum power point, because the variable step size is sensitive to external factors. Therefore, this paper proposes an enhanced maximum power point tracking algorithm that can have fast dynamic response, low oscillations, and high maximum power point tracking efficiency. To achieve these advantages, the proposed maximum power point tracking algorithm uses two methods that can apply the optimal step size to each operating range. In the operating range near the maximum power point, a small fixed step size is used to minimize the oscillations at the maximum power point. In contrast, in the operating range far from the maximum power point, a variable step size proportional to the slope of the power-voltage curve of PV module is used to achieve fast tracking speed under dynamic weather conditions. As a result, the proposed algorithm can achieve higher maximum power point tracking efficiency, faster dynamic response, and lower oscillations than the basic and adaptive algorithms. The theoretical analysis and performance of the proposed algorithm were verified by experimental results. In addition, the comparative experimental results of the proposed algorithm with the other maximum power point tracking algorithms show the superiority of the proposed algorithm.

A Noval Improved Variable Step-Size Incremental Resistance Maximum Power Point Tracking Controller for Photo Voltaic System Under Partial Shading Condition

2019 ◽  
Vol 16 (2) ◽  
pp. 740-744
Author(s):  
R. Geethamani ◽  
C. Pavithra ◽  
B. Niranjana ◽  
V. Gomathy ◽  
P. Chitra
Keyword(s):  
Maximum Power Point Tracking ◽  
Variable Step Size ◽  
Step Size ◽  
Pv System ◽  
Maximum Power Point ◽  
Partial Shading ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Variable Step ◽  
Power Point

A Variable step size Incremental resistance algorithm for PV system was designed for maximum power point tracking. The outputs are generated with help of MATLAB/SIMLUNK. The performance of the PV system for partial shading condition was observed. The output for the system was found to be more efficient and attains stability much faster than any other controller. The power output can be controlled by varying the scaling factor.

A New Scheme Based on Climbing Method for Maximum Photovoltaic Power Tracking Control

2014 ◽  
Vol 707 ◽  
pp. 377-380
Author(s):  
Bo Qiang Xu ◽  
Jin Bo Li
Keyword(s):  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Variable Step Size ◽  
Step Size ◽  
Maximum Power Point ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Photovoltaic Arrays ◽  
Conductance Method ◽  
Power Point

The maximum power point tracking (MPPT) of photovoltaic arrays can increase the output power of the photovoltaic systerm, improve the utilization of solar energy. This paper describes the output characteristics of the photovoltaic arrays and the principle of maximum power point tracking,then,based on Incremental conductance method, proposes a sub-type of the variable step size MPPT algorithm. simulated using MATLAB/Simulink, the final results show that the proposed algorithm is able to quickly track the maximum power point and power concussion problem has been significantly improved.

Sign in / Sign up

Export Citation Format

Share Document