scholarly journals Modeling of Combined Lead Fast Reactor and Concentrating Solar Power Supercritical Carbon Dioxide Cycles to Demonstrate Feasibility, Efficiency Gains, and Cost Reductions

2021 ◽  
Vol 13 (22) ◽  
pp. 12428
Author(s):  
Brian T. White ◽  
Michael J. Wagner ◽  
Ty Neises ◽  
Cory Stansbury ◽  
Ben Lindley
Keyword(s):  
Energy Storage ◽  
Heat Exchanger ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Supercritical Co2 ◽  
Solar Power ◽  
Combined Cycle ◽  
Outlet Temperature ◽  
Brayton Cycle ◽  
Concentrating Solar Power

Solar power has innate issues with weather, grid demand and time of day, which can be mitigated through use of thermal energy storage for concentrating solar power (CSP). Nuclear reactors, including lead-cooled fast reactors (LFRs), can adjust power output according to demand; but with high fixed costs and low operating costs, there may not be sufficient economic incentive to make this worthwhile. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO2 Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low-demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO2-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO2 Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high-temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near-perfect heat storage efficiency but increasing cost with additional cycle components.

scholarly journals Modeling of Combined Lead Fast Reactor and Concentrating Solar Power Supercritical Carbon Dioxide Cycles to Demonstrate Feasibility, Efficiency Gains, and Cost Reductions

2021 ◽  
Author(s):  
Brian White ◽  
Michael Wagner ◽  
Ty Neises ◽  
Cory Stansbury ◽  
Ben Lindley
Keyword(s):  
Energy Storage ◽  
Heat Exchanger ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Solar Power ◽  
Time Of Day ◽  
Combined Cycle ◽  
Outlet Temperature ◽  
Brayton Cycle ◽  
Concentrating Solar Power

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

Supercritical Carbon Dioxide Power Cycle Configurations for Use in Concentrating Solar Power Systems

2012 ◽  
Author(s):  
Craig S. Turchi ◽  
Zhiwen Ma ◽  
John Dyreby
Keyword(s):  
Carbon Dioxide ◽  
Energy Storage ◽  
Molten Salt ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Solar Power ◽  
Brayton Cycle ◽  
Concentrating Solar Power ◽  
Power Cycle ◽  
Cycle Efficiency

Concentrating Solar Power (CSP) plants utilize oil, molten salt or steam as the heat transfer fluid (HTF) to transfer solar energy to the power block. These fluids have properties that limit plant performance; for example, the synthetic oil and molten salt have upper temperature limits of approximately 390°C and 565°C, respectively. While direct steam generation has been tested, it requires complex controls and has limited options for integration of thermal energy storage. Use of carbon dioxide as the HTF and power cycle working fluid offers the potential to increase thermal cycle efficiency while maintaining simplicity of operation and thermal storage options. Supercritical CO2 (s-CO2) operated in a closed-loop recompression Brayton cycle offers the potential of higher cycle efficiency versus superheated or supercritical steam cycles at temperatures relevant for CSP applications. Brayton-cycle systems using s-CO2 have smaller weight and volume, lower thermal mass, and less complex power blocks versus Rankine cycles due to the higher density of the fluid and simpler cycle design. Many s-CO2 Brayton power cycle configurations have been proposed and studied for nuclear applications; the most promising candidates include recompression, precompression, and partial cooling cycles. Three factors are important for incorporating s-CO2 into CSP plants: superior performance vs. steam Rankine cycles, ability to integrate thermal energy storage, and dry-cooling. This paper will present air-cooled s-CO2 cycle configurations specifically selected for a CSP application. The systems will consider 10-MW power blocks that are tower-mounted with an s-CO2 HTF and 100-MW, ground-mounted s-CO2 power blocks designed to receive molten salt HTF from a power tower.

Viability Assessment of a Concentrated Solar Power Tower With a Supercritical CO2 Brayton Cycle Power Plant

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Ali Sulaiman Alsagri ◽  
Andrew Chiasson ◽  
Mohamed Gadalla
Keyword(s):  
Energy Storage ◽  
Molten Salt ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Supercritical Co2 ◽  
Solar Power ◽  
Capacity Factor ◽  
Brayton Cycle ◽  
Concentrated Solar Power ◽  
Solar Power Tower

The aim of this study was to conduct thermodynamic and economic analyses of a concentrated solar power (CSP) plant to drive a supercritical CO2 recompression Brayton cycle. The objectives were to assess the system viability in a location of moderate-to-high-temperature solar availability to sCO2 power block during the day and to investigate the role of thermal energy storage with 4, 8, 12, and 16 h of storage to increase the solar share and the yearly energy generating capacity. A case study of system optimization and evaluation is presented in a city in Saudi Arabia (Riyadh). To achieve the highest energy production per unit cost, the heliostat geometry field design integrated with a sCO2 Brayton cycle with a molten-salt thermal energy storage (TES) dispatch system and the corresponding operating parameters are optimized. A solar power tower (SPT) is a type of CSP system that is of particular interest in this research because it can operate at relatively high temperatures. The present SPT-TES field comprises of heliostat field mirrors, a solar tower, a receiver, heat exchangers, and two molten-salt TES tanks. The main thermoeconomic indicators are the capacity factor and the levelized cost of electricity (LCOE). The research findings indicate that SPT-TES with a supercritical CO2 power cycle is economically viable with 12 h thermal storage using molten salt. The results also show that integrating 12 h-TES with an SPT has a high positive impact on the capacity factor of 60% at the optimum LCOE of $0.1078/kW h.

Numerical Analysis of Latent Thermal Energy Storage System With Embedded Thermosyphons

2012 ◽  
Author(s):  
Karthik Nithyanandam ◽  
Ranga Pitchumani
Keyword(s):  
Thermal Conductivity ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Solar Power ◽  
Storage System ◽  
High Energy ◽  
Concentrating Solar Power ◽  
Discharge Performance ◽  
Low Thermal Conductivity

Latent thermal energy storage (LTES) system offers high energy storage density and nearly isothermal operation for concentrating solar power generation. However, the low thermal conductivity possessed by the phase change material (PCM) used in LTES system limits the heat transfer rates. Utilizing thermosyphons to charge or discharge a LTES system offers a promising engineering solution to compensate for the low thermal conductivity of the PCM. The present work numerically investigates the enhancement in the thermal performance of charging and discharging process of LTES system by embedding thermosyphons. A transient, computational analysis of the LTES system with embedded thermosyphons is performed for both charging and discharging cycles. The influence of the design configuration of the system and the arrangement of the thermosyphons on the charge and discharge performance of the LTES installed in a concentrating solar power plant (CSP) is analyzed to identify configurations that lead to improved effectiveness.

scholarly journals Preliminary prospects of a Pumped Thermal Energy Storage (PTES) based on a supercritical CO2 Brayton cycle

2021 ◽  
Author(s):  
Karin Astrid Senta Edel ◽  
František Hrdlička ◽  
Václav Novotný
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Supercritical Co2 ◽  
Storage Systems ◽  
Renewable Energy Sources ◽  
Brayton Cycle ◽  
Term Energy ◽  
Weather Changes

As part of the change towards a higher deployment of renewable energy sources, which naturally deliver energy intermittently, the need for energy storage systems is increasing. For compensation of disturbance in power production due to inter-day to seasonal weather changes, long-term energy storage is required. In the spectrum of storage systems, one out of a few geographically independent possibilities is the storage of electricity in heat, so-called Carnot-Batteries. This paper presents a Pumped Thermal Energy Storage (PTES) system based on a recuperated supercritical CO2 Brayton cycle. The modelled system provides a round-trip efficiency of 38.9%.

Sign in / Sign up

Export Citation Format

Share Document