scholarly journals Mechanical Performance of Lime Mortar Coatings for Rehabilitation of Masonry Elements in Old and Historical Buildings

2021 ◽  
Vol 13 (6) ◽  
pp. 3281
Author(s):  
Fernando G. Branco ◽  
Maria de Lurdes Belgas ◽  
Cátia Mendes ◽  
Luís Pereira ◽  
José Marcos Ortega
Keyword(s):  
Water Absorption ◽  
Mechanical Performance ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Crushed Rock ◽  
Rock Powder ◽  
Hydraulic Lime ◽  
Lime Mortar ◽  
Compressive And Flexural Strengths

The use of lime as a binder in masonry lining mortars plays an important role in its conservation and durability. Knowledge of the mechanical characteristics of pre-existing and restoration mortars is essential in order to guarantee the compatibility between them and for avoiding the appearance of pathologies. The paper mainly focuses on the study of the mechanical performance of lime-based mortars to be applied in rehabilitation works in old buildings. Four types of mortars were tested with very similar workability, based on lime putty, aerial lime, and hydraulic lime. Sand and crushed rock powder were used as aggregates. Compressive and flexural strengths of the mortars were determined, as well as their ultrasonic pulse velocity. Furthermore, specific tests were carried out to characterize the performance of the mortar when used as a binder for plasters and coatings, such as the development of cracking, superficial water absorption under low pressure, and pull-off strength. According to the results obtained, mortars with lime putty showed better mechanical properties, while those with aerial lime had better behavior regarding water absorption under pressure. Despite that, it was generally possible to verify the adequacy of the studied mortars to be used in the rehabilitation of masonry elements.

scholarly journals Effects of a Real Exposure Class XC4 Mediterranean Climate Environment in the Behavior of Mortars Made Using Ternary Binders with Addition of Slag, Fly Ash and Limestone

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5848
Author(s):  
Javier Ibáñez-Gosálvez ◽  
Teresa Real-Herraiz ◽  
José Marcos Ortega
Keyword(s):  
Fly Ash ◽  
Mediterranean Climate ◽  
Mechanical Performance ◽  
Ultrasonic Pulse Velocity ◽  
Pore Network ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Industry ◽  
Granulated Blast Furnace Slag ◽  
Compressive And Flexural Strengths

For improving the contribution of the cement industry to mitigate global warming, many strategies have been put into practice, such as the use of eco-friendly cements with the incorporation of additions substituting clinker. Nevertheless, the use of ternary binders for the production of commercial cements is still reduced, particularly in Spain. The purpose of this research is to characterize the long-term influence produced by the exposure to a real in situ inland Mediterranean climate condition in the pore network, parameters related to durability and mechanical performance of mortars made with ternary binders, which incorporated limestone, fly ash, and ground granulated blast-furnace slag, in comparison with mortars without additions and binary blended mortars. The site verified the specifications of exposure class XC4 of Eurocode 2. The ternary and binary binders accomplished the prescriptions of cement type CEM II/B. The pore network was studied with mercury intrusion porosimetry and electrical resistivity. Water absorption, diffusion coefficient, carbonation depth, ultrasonic pulse velocity, compressive and flexural strengths have been determined. The exposure to the environment produced after 250 days an increase in porosity, a loss of pore refinement, a rise of the carbonation depths, and a reduction in the mechanical strengths, highlighting the better overall performance of ternary mortar with both fly ash and slag.

The Feasibility of Basalt Rock Powder and Superfine Sand as Partial Replacement Materials for Portland Cement and Artificial Sand in Cement Mortar

2019 ◽  
Vol 1 (1) ◽  
Author(s):  
Hongxia Qiao ◽  
Desire Ndahirwa ◽  
Yuanke Li ◽  
Jinke Liang
Keyword(s):  
Portland Cement ◽  
Mechanical Performance ◽  
Cement Mortar ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Partial Replacement ◽  
Rock Powder ◽  
Research Gap ◽  
Basalt Rock

The research gap on the feasibility of basalt rock powder (BRP) and superfine sand (SS) in preparation of cement mortar is significant. Thisstudy examines probable changes occurred in the modified cement mortar due to incorporation of certain quantity of basalt rock powder andsuperfine sand in mixture proportion. The cement mortar included Portland cement, artificial sand and water as principal mixture constituents. Then, basalt rock powder and superfine sand were added as partial replacement materials for Portland cement and artificial sand respectively. Therefore, replacement percentages were 10%, 15%, 20%, 25% and 30% when the basalt rock powder replaced Portland cement and in case the artificial sand was replaced by superfine sand, 10%, 20%, 30%, 40% and 50%. Then, the strength indexes such as flexural strength, compressive strength, ultrasonic pulse velocity and dynamic elastic modulus were investigated. The results show that the presence of basalt rock powder in mixture proportion increased the flexural and compressive strengths of cement mortar however the cement mortar that contained superfine sand illustrated inadequate mechanical performance as flexural and compressive strengths decreased remarkably. Moreover, when basalt rock powder and superfine sand were included together in mixture proportion, the cement mortar’s mechanical performance declined compared to that of the reference cement mortar. Despite the fact that basalt rock powder and superfine sand weakened the cement mortar’s mechanical properties, it was found that they can be added into the cement mortar as partial replacement of Portland cement and artificial sand in the following ratios: from 10% to 25% when basalt rock powder replaces Portland cement and from 10% to 20% when artificial sand is replaced by superfine sand.

scholarly journals Attempts to Improve the Subsurface Properties of Horizontally-Formed Cementitious Composites Using Tin(II) Fluoride Nanoparticles

Coatings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 83 ◽  
Author(s):  
Kamil Krzywiński ◽  
Łukasz Sadowski ◽  
Jacek Szymanowski ◽  
Andrzej Żak ◽  
Magdalena Piechówka-Mielnik
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Abrasion Resistance ◽  
Mechanical Performance ◽  
Reference Sample ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cementitious Composites ◽  
Fluoride Nanoparticles

This article presents studies that were performed in order to improve the subsurface properties of horizontally-formed cementitious composites using tin(II) fluoride nanoparticles. The main aim of the study was to solve the problem of the decrease in subsurface properties caused by mortar bleeding and the segregation of the aggregate along the height of the overlay. The article also aims to highlight the patch grabbing difficulties that occur during the process of forming horizontally-formed cementitious composites. Four specimens were analyzed: one reference sample and three samples modified with the addition of 0.5, 1.0, and 1.5% of tin(II) fluoride nanoparticles in relation to the cement mass. To analyze the mechanical properties of the specimens, non-destructive (ultrasonic pulse velocity) and destructive tests (flexural tensile strength, compressive strength, abrasion resistance, pull-off strength) were performed. It was indicated that due to the addition of the tin(II) fluoride, it was possible to enhance the subsurface tensile strength and abrasion resistance of the tested cementitious composites. To confirm the obtained macroscopic results, the porosity of the subsurface was measured using SEM. It was also shown that the addition of the tin(II) fluoride nanoparticles did not reduce its flexural and compressive strength. The results show that horizontally-formed cementitious composites with the addition of 1.0% of tin(II) fluoride nanoparticles in relation to the cement mass obtained the most effective mechanical performance, especially with regard to subsurface properties.

scholarly journals A Study on Tannery Sludge as a Raw Material for Cement Mortar

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1562 ◽  
Author(s):  
Jurgita Malaiškienė ◽  
Olga Kizinievič ◽  
Viktor Kizinievič
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Cement Mortar ◽  
Ultrasonic Pulse Velocity ◽  
Xrd Analysis ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Raw Material ◽  
Tannery Sludge ◽  
Limit Values

The paper analyses the properties (chemical and mineral composition, microstructure, density, etc.) of recycled tannery sludge (TS) and the possibilities for using it in cement mortar mixture. Mortar specimens containing 3–12% of tannery sludge by weight of cement and 3–9% of tannery sludge by weight of sand were tested. Flowability, density, ultrasonic pulse velocity (UPV), flexural and compressive strength, water absorption and sorptivity of the mortar were analysed. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis of tannery sludge and mortar are presented. The tests revealed that replacement of 6% of cement with tannery sludge in the mix increased flexural and compressive strength and UPV values, whereas water absorption decreased. SEM and XRD analysis revealed that specimens with tannery sludge contained lower amounts of ettringite and higher amounts of portlandite; the obtained structure was denser and contained more calcium hydrosilicates (C-S-H). Chromium leaching values in cement mortars were found not to exceed the limit values set forth in Directive 2003/33/EC.

scholarly journals Using Carbonated BOF Slag Aggregates in Alkali-Activated Concretes

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1288 ◽  
Author(s):  
Mohammad Mastali ◽  
Ahmad Alzaza ◽  
Khaled Mohammad Shaad ◽  
Paivo Kinnunen ◽  
Zahra Abdollahnejad ◽  
...  
Keyword(s):  
Drying Shrinkage ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Basic Oxygen Furnace ◽  
Pulse Velocity ◽  
Maximum Enhancement ◽  
Bof Slag ◽  
Negative Impacts ◽  
Compressive And Flexural Strengths ◽  
Alkali Activated

This experimental study aimed to develop alkali-activated concretes containing carbonated basic oxygen furnace (BOF) slag aggregates. In the first stage, the impacts of replacing normal aggregates with carbonated BOF slag aggregates in different alkali-activated concretes were determined by assessing mechanical properties (compressive and flexural strengths), morphology, thermogravimetric analyses (TGA), differential thermogravimetry (DTG) and the crystalline phases using X-ray diffraction analysis. Second, the developed plain alkali-activated concrete was reinforced by different fibre types and dosages to limit the negative impacts of the drying shrinkage and to improve strength. Therefore, the effects of using different fibre contents (1% and 1.5% in Vol.) and types (Polyvinyl alcohol [PVA], Polypropylene [PP], basalt, cellulose and indented short-length steel) on hardened state properties were evaluated. These evaluations were expressed in terms of the compressive and flexural strengths, ultrasonic pulse velocity, mass changes, drying shrinkage and efflorescence. Then, the impacts of aggressive conditions on the hardened properties of fibre-reinforced alkali-activated concretes were evaluated under carbonation, high temperature and freeze/thaw tests. The results showed that using carbonated BOF slag aggregates led to obtain higher strength than using normal aggregates in alkali activated concretes. Moreover, the maximum enhancement due to reinforcing the mixtures was recorded in alkali-activated concretes with steel fibres.

scholarly journals Enhancing Sustainable Concrete Properties by Green Vegetable Substance

2018 ◽  
Vol 7 (4.37) ◽  
pp. 219
Author(s):  
Zainab Hasan Abdulabbas ◽  
Marwa Asad Salih ◽  
Ali Talib Jasim
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Soft Drink ◽  
Gum Arabic ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Waste Materials ◽  
Concrete Properties ◽  
Concrete Production

From several points of view, disposal of waste materials in an environment is respected to be a significant problem because of its very low biodegradability and existence in huge quantities. Waste of plastic and metal bottles caps, cans of juices and soft drink, and tires rubber being among the most pronounced. This study was conducted to evaluate the efficiency of reusing these waste materials in concrete production and solve the segregation problem. As segregation increases in concrete involving these waste materials due to lighter weight of them relative to nature aggregate, therefore, attention was intensive on using natural product (Gum Arabic) that is an environmentally friendly chemical material for improving concrete properties. The conducted tests include; compressive strength, flexural strength, splitting tensile strength, density, water absorption, and ultrasonic pulse velocity. The results showed that replacing the volume of coarse aggregate by 25% compacted bottles caps and pull-tab of cans, 20% the plastic bottle caps, and 25% tires rubber shreds used decreased the mechanical properties of concrete to some extent less than reference mix and they were enhanced by employing Gum Arabic. In addition, the employment of Gum Arabic as liquid in concrete mixes developed the mechanical properties of concrete, reduced segregation, however raised the water absorption percent and declined the density of concrete.  

scholarly journals Characteristics of Preplaced Aggregate Concrete Fabricated with Alkali-Activated Slag/Fly Ash Cements

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 591
Author(s):  
Salman Siddique ◽  
Hyeju Kim ◽  
Hyemin Son ◽  
Jeong Gook Jang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Grout ◽  
Aggregate Concrete ◽  
Alkali Activated ◽  
Alkali Activated Cement

This study assesses the characteristics of preplaced aggregate concrete prepared with alkali-activated cement grout as an adhesive binder. Various binary blends of slag and fly ash without fine aggregate as a filler material were considered along with different solution-to-solid ratios. The properties of fresh and hardened grout along with the properties of hardened preplaced concrete were investigated, as were the compressive strength, ultrasonic pulse velocity, density, water absorption and total voids of the preplaced concrete. The results indicated that alkali-activated cement grout has better flowability characteristics and compressive strength than conventional cement grout. As a result, the mechanical performance of the preplaced aggregate concrete was significantly improved. The results pertaining to the water absorption and porosity revealed that the alkali-activated preplaced aggregate concrete is more resistant to water permeation. The filling capacity based on the ultrasonic pulse velocity value is discussed to comment on the wrapping ability of alkali-activated cement grout.

scholarly journals Microstructure, Durability and Mechanical Properties of Mortars Prepared Using Ternary Binders with Addition of Slag, Fly Ash and Limestone

2021 ◽  
Vol 11 (14) ◽  
pp. 6388
Author(s):  
Javier Ibáñez-Gosálvez ◽  
Teresa Real-Herraiz ◽  
José Marcos Ortega
Keyword(s):  
Fly Ash ◽  
Mercury Intrusion Porosimetry ◽  
Mechanical Performance ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Production ◽  
Mechanical Strengths ◽  
Furnace Slag

In order to improve the contribution to sustainability of cement production, several strategies have been developed, such as the incorporation of additions as clinker replacement. Regarding the production of commercial cements with additions, those made with binary binders are mostly produced. However, the use of ternary binders for manufacturing commercial cements is still very low, at least in Spain, and they could also be an adequate solution for producing eco-friendly cements. The objective of this research is to study the effects in the long term produced by ternary binders which combine the additions of blast furnace slag, fly ash and limestone in the microstructure, durability and mechanical performance of mortars, compared to mortars without additions and mortars made with binary binders. The ternary and binary binders accomplished the prescriptions for a cement type CEM II/B. The microstructure was characterized using mercury intrusion porosimetry, electrical resistivity and differential thermal analysis. Absorption after immersion, diffusion coefficient, mechanical strengths and ultrasonic pulse velocity were studied. The best performance was noted for ternary binder with both slag and fly ash, probably produced by the synergetic effects of slag hydration and fly ash pozzolanic reactions. These effects were more noticeable regarding the compressive strength.

scholarly journals Mechanical Properties of Na2CO3-Activated High-Volume GGBFS Cement Paste

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Taewan Kim ◽  
Yubin Jun
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
High Volume ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Strength Development ◽  
X Ray Diffraction ◽  
Granulated Blast Furnace Slag ◽  
Dry Shrinkage

The use of Na2CO3 to improve the mechanical properties of high-volume slag cement (HVSC) is experimentally investigated in this study. Ordinary Portland cement (OPC) was replaced with 50, 60, 70, 80, and 90% ground-granulated blast-furnace slag (GGBFS) by weight. Na2CO3 was added at 0, 1, 2, 3, 4, and 5 wt.% of HVSC (OPC + GGBFS). The compressive strength, water absorption, ultrasonic pulse velocity, dry shrinkage, and X-ray diffraction spectra of the Na2CO3-activated HVSC pastes were analyzed. The results indicate that Na2CO3 was effective for improving the strength of HVSC samples at both early and later ages. There was a trend of increasing HVSC sample strength with increasing Na2CO3 content. The 5% Na2CO3-activated HVSC (50% OPC + 50% GGBFS) paste had the best combination of early to later-age strength development and exhibited the highest UPV and the lowest water absorption among the Na2CO3-activated HVSC samples at later age.

scholarly journals INVESTIGATION THE EFFECTS OF GREEN MORTAR PARAMETERS USING ANALYTICAL METHODS

2021 ◽  
pp. 1-17
Author(s):  
Eethar Dawood ◽  
Mafaz Abdullah
Keyword(s):  
Regression Analysis ◽  
Ecological Impact ◽  
Steel Slag ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Flow Density ◽  
Second Phase ◽  
Waste Glass Powder ◽  
Compressive And Flexural Strengths

The various green mortar mixes have been used in this study using various percentages of waste glass powder (WGP), steel slag (SG) and Micro-silica fume(SF).The different properties of flow, density, ultrasonic pulse velocity (UPV), compressive and flexural strengths have been tested for such green mortar in the  first phase of experimental work. The second phase deals with the regression analysis of such properties. Whereas, the analysis of the results have also been using the integrated AHP and TOPSIS methods for selection the best performance of the green mortar due to the ecological effects of such materials. The results showed that the use of 70%OPC+8%WGP+12%SG+10% SF indicated as the best performance in term of ecological impact compared with other mortar mixes. Also, the regression analysis using the integrated AHP and TOPSIS methods gives an effective strategy for the selection of the best mortar mix.

Sign in / Sign up

Export Citation Format

Share Document