scholarly journals Properties of Precast Concrete Using Food Industry-Filtered Recycled Diatoms

2021 ◽  
Vol 13 (6) ◽  
pp. 3137
Author(s):  
Carlos Rodriguez ◽  
Isabel Miñano ◽  
Carlos Parra ◽  
Pedro Pujante ◽  
Francisco Benito
Keyword(s):  
Portland Cement ◽  
Food Industry ◽  
Precast Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Chloride Ingress ◽  
Capillary Water ◽  
Experimental Campaign ◽  
Cast Concrete

The concrete industry is under increasing pressure to reduce greenhouse gas emissions. An immediate solution is to minimize the amount of Portland cement used by partially substituting other supplementary cementitious materials. This article presents the results of an experimental campaign on the influence of replacing Portland cement with both calcined and uncalcined diatomites from the filtration of beer and wine in the production of elements made of vibro-pressed pre-cast concrete, such as pipes. Additionally, a natural diatomite is used. The mechanical properties, capillary water absorption, carbonation, and chloride ingress are tested. The results obtained show the possibility of using natural and recycled diatomites on an industrial scale, which can improve even the long term properties of prepared precast concrete.

scholarly journals Use of supplementary cementitious materials (SCMs) in reinforced concrete systems – Benefits and limitations

2020 ◽  
Vol 10 (2) ◽  
pp. 147-164
Author(s):  
Radhakrishna G. Pillai ◽  
Ravindra Gettu ◽  
Manu Santhanam
Keyword(s):  
Drying Shrinkage ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Chloride Ingress ◽  
Shrinkage Cracking ◽  
Carbonation Resistance ◽  
Chloride Attack ◽  
Cementitious Systems

About a decade of research carried out at IIT Madras on cementitious systems has shown that the partial replacement of portland cement with supplementary cementitious materials (SCMs) has benefits as well as limitations. The SCMs do not adversely affect the long-term compressive strength and drying shrinkage of concretes, though there may be some compromise in workability and the resistance against plastic shrinkage cracking. Through the assessment of the chloride ingress rate in concrete and chloride threshold of steel, it is evident that the use of SCMs could significantly enhance the service life under chloride attack, though there is a reduction of the carbonation resistance. More importantly, SCMs can lead to significant reduction of the carbon footprint of concrete, and hence, are essential to achieve sustainability.

Evaluation of strength of concrete on different initial exposure condition

2020 ◽  
Vol 13 ◽  
Author(s):  
Sri Ram Krishna Mishra ◽  
Pradeep Kumar Ghosh ◽  
Manoj Kulshreshtha
Keyword(s):  
Portland Cement ◽  
High Strength ◽  
Cementitious Materials ◽  
General Purpose ◽  
Supplementary Cementitious Materials ◽  
Exposure Condition ◽  
Portland Cement Concrete ◽  
Initial Exposure ◽  
Skilled Manpower ◽  
Standard Practices

Background: The previous studies have focused curing effect of mainly on high strength concrete, where strict supervision is maintained. This study is based upon general purpose concreting work for commercial and residential construction in absence of skilled manpower and supervision. Objective: The objective of this study is to establish a thumb rule to provide 7 days initial curing for maintaining quality for unsupervised concreting irrelevant to type of cement and grading. Methods: In this study concrete samples made with locally available commercial cements were cured for various initial exposure. Results: The results shows that concrete cured after a gap of 4 days from the time of de-moulding have given lowest strength as compared to concrete cured in standard practices i.e. where proper curing protocol had been followed. Conclusion: Initial curing is most important aspect of gaining desired strength. The findings after this study shows that curing affects the strength of concrete in variable grading. Initial curing has great importance for concrete with all types of Portland cement. Concrete with supplementary cementitious materials gives lowest strength initially but results higher strength after 28 days as compared to Portland cement.

scholarly journals Special Issue: Supplementary Cementitious Materials in Concrete, Part I

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2291
Author(s):  
Alessandro P. Fantilli ◽  
Daria Jóźwiak-Niedźwiedzka
Keyword(s):  
Environmental Impact ◽  
Portland Cement ◽  
Building Materials ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Special Issue ◽  
Cement Production ◽  
Concrete Part

The environmental impact of the Portland cement production and the large use of cement-based building materials is a growing problem [...]

scholarly journals A Review of the Mechanical Properties and Durability of Ecological Concretes in a Cold Climate in Comparison to Standard Ordinary Portland Cement-Based Concrete

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3467
Author(s):  
Ankit Kothari ◽  
Karin Habermehl-Cwirzen ◽  
Hans Hedlund ◽  
Andrzej Cwirzen
Keyword(s):  
Carbon Dioxide ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Cementitious Materials ◽  
Cold Climate ◽  
Supplementary Cementitious Materials ◽  
Short Exposure ◽  
Chemical Admixtures ◽  
Composite Cements ◽  
Alkali Activated

Most of the currently used concretes are based on ordinary Portland cement (OPC) which results in a high carbon dioxide footprint and thus has a negative environmental impact. Replacing OPCs, partially or fully by ecological binders, i.e., supplementary cementitious materials (SCMs) or alternative binders, aims to decrease the carbon dioxide footprint. Both solutions introduced a number of technological problems, including their performance, when exposed to low, subfreezing temperatures during casting operations and the hardening stage. This review indicates that the present knowledge enables the production of OPC-based concretes at temperatures as low as −10 °C, without the need of any additional measures such as, e.g., heating. Conversely, composite cements containing SCMs or alkali-activated binders (AACs) showed mixed performances, ranging from inferior to superior in comparison with OPC. Most concretes based on composite cements require pre/post heat curing or only a short exposure to sub-zero temperatures. At the same time, certain alkali-activated systems performed very well even at −20 °C without the need for additional curing. Chemical admixtures developed for OPC do not always perform well in other binder systems. This review showed that there is only a limited knowledge on how chemical admixtures work in ecological concretes at low temperatures and how to accelerate the hydration rate of composite cements containing high amounts of SCMs or AACs, when these are cured at subfreezing temperatures.

Research Progress on the Hydration of Portland Cement with Calcined Clay and Limestone

2021 ◽  
Vol 1036 ◽  
pp. 240-246
Author(s):  
Jin Tang ◽  
Su Hua Ma ◽  
Wei Feng Li ◽  
Hui Yang ◽  
Xiao Dong Shen
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Research Progress ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Early Hydration ◽  
Calcined Clay ◽  
Dense Microstructure

The use of calcined clay and limestone as supplementary cementitious materials, can have a certain influence on the hydration of Portland cement. This paper reviewed the influence of limestone and calcined clay and the mixture of limestone and calcined clay on the hydration of cement. Both limestone and calcined clay accelerate the hydration reaction in the early hydration age and enhance the properties of cement. Limestone reacts with C3A to form carboaluminate, which indirectly stabilized the presence of ettringite, while calcined clay consumed portlandite to form C-(A)-S-H gel, additional hydration products promote the densification of pore structure and increase the mechanical properties. The synergistic effect of calcined clay and limestone stabilize the existence of ettringite and stimulate the further formation of carboaluminate, as well as the C-(A)-S-H gel, contributed to a dense microstructure.

scholarly journals Long-term mechanical and shrinkage properties of cementitious grouts for structural repair

2019 ◽  
Vol 4 ◽  
pp. 9-15
Author(s):  
Md Shamsuddoha ◽  
Götz Hüsken ◽  
Wolfram Schmidt ◽  
Hans-Carsten Kühne ◽  
Matthias Baeßler
Keyword(s):  
Fly Ash ◽  
Flexural Strength ◽  
Cementitious Materials ◽  
Response Surfaces ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Structural Repair ◽  
Positive Effects ◽  
Micro Silica

Grouts have numerous applications in construction industry such as joint sealing, structural repair, and connections in precast elements. They are particularly favoured in rehabilitation of structures due to penetrability and convenience of application. Grouts for repair applications typically require high-performance properties such as rapid strength development and superior shrinkage characteristics. Sometimes industrial by-products referred as supplementary cementitious materials (SCM) are used with neat cement due to their capabilities to provide binding properties at delayed stage. Micro silica, fly ash and metakaolin are such SCMs, those can modify and improve properties of cement products. This study aims at investigating long-term mass loss and linear shrinkage along with long-term compressive and flexural strength for grouts produced from ultrafine cement and SCMs. A series of mixtures were formulated to observe the effect of SCMs on these grout properties. Properties were determined after 365 days of curing at 23oC and 55% relative humidity. The effect of SCMs on the properties are characterised by statistical models. Response surfaces were constructed to quantify these properties in relation to SCMs replacement. The results suggested that shrinkage was reduced by metakaolin, while micro silica and fly ash had positive effects on compressive and flexural strength, respectively.

scholarly journals The Potentials of Iron and Steel Slags as Supplementary Cementitious Materials in the Nigerian Construction Industry: A Review

2018 ◽  
Vol 2 (2) ◽  
pp. 208-218
Author(s):  
O. R. Ogirigbo ◽  
J. O. Ukpata ◽  
I. Inerhunwa
Keyword(s):  
Portland Cement ◽  
Construction Industry ◽  
Waste Product ◽  
Steel Production ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Iron And Steel ◽  
Tropical Environments ◽  
Iron And Steel Production

Ground Granulated Blast Furnace Slag (GGBS) is a type of Supplementary Cementitious Material (SCM) that is currently being used extensively in the global construction industry. SCMs are cheaper than Portland cement, help to improve certain properties of concrete and also help to reduce the environmental footprint associated with the production of Portland cement. GGBS is readily available in most parts of the world as a waste product from iron and steel production. However, its use as a SCM in some countries has not been fully maximized. This is primarily because of lack of documented studies on the properties of GGBS that influences its suitability as a SCM, especially in tropical environments. This paper reviewed the use of GGBS as a SCM for the partial replacement of Portland cement, with particular emphasis on its potential use in tropical warm environments such as Nigeria and other similar countries.

Performance of Impure Calcined Clay as a Pozzolan in Concrete

2020 ◽  
pp. 036119812095314
Author(s):  
Khashayar Jafari ◽  
Farshad Rajabipour
Keyword(s):  
Portland Cement ◽  
Drying Shrinkage ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Natural Pozzolan ◽  
Quartz Content ◽  
Calcined Clay ◽  
Air Content ◽  
Sand And Gravel

Supplementary cementitious materials (SCMs) are natural or industrial by-product materials which are used to improve the performance, durability, and sustainability of concrete mixtures. Motivated by the recent reports on shortage of conventional SCMs, impure calcined clays (CCs) are receiving attention as abundant alternative pozzolans for concrete. In this study, a clay slurry resulting from washing aggregates in a commercial sand and gravel pit was investigated. This source clay was dried and calcined, and the properties and pozzolanic performance of the resulting CC was evaluated. It was observed that despite having a large (>50%wt.) inert quartz content, the CC met all ASTM C618-19 (AASHTO M295) requirements for natural pozzolan. A pavement-grade concrete mixture containing 20%CC as a cement replacement (by weight) produced desired workability and fresh and hardened air content. Strength development was slightly below the control. The use of CC improved the durability of concrete with respect to chloride penetration, alkali–silica reaction, and drying shrinkage in comparison with a control (100% Portland cement) mixture. In addition, ternary limestone-calcined clay–cement and slag-calcined clay–cement mortar mixtures showed excellent strength development while replacing nearly 50% of the Portland cement.

Sign in / Sign up

Export Citation Format

Share Document