scholarly journals Combined Pretreatment by Ultrasound and Struvite Precipitation of Raw Substrates: A Strategy to Overcome C/N Ratio Unbalance in Nitrogen-Rich Anaerobic Co-Digestion Systems

2021 ◽  
Vol 13 (4) ◽  
pp. 2175
Author(s):  
Renata D’arc Coura ◽  
Ana Cristina Rodrigues ◽  
Joaquim Mamede Alonso ◽  
Ana Isabel Ferraz ◽  
Luis Miguel Brito ◽  
...  
Keyword(s):  
Hydraulic Retention Time ◽  
Liquid Fraction ◽  
Operating Time ◽  
Chemical Precipitation ◽  
Ammonium Nitrogen ◽  
Precipitation Process ◽  
Combined Pretreatment ◽  
Nitrogen Ratio ◽  
Struvite Precipitation ◽  
Marine Salt

The present study aimed to optimize the struvite chemical precipitation process in nitrogen-rich anaerobic co-digestion systems. Struvite precipitation experiments were carried out using a mixture of cattle slurry liquid fraction and sewage sludge, with and without ultrasound pretreatment. Marine salt or MgCl2 were used as magnesium source in NH4+:Mg2+ stoichiometric proportions of 1:1.5 and 1:3. Under the tested conditions, ammonium nitrogen and orthophosphate were removed from the mixed liquor with a maximum observed efficiency of 43% and 92%, respectively, when the ultrasound treatment was applied prior to struvite precipitation, using MgCl2 as source of magnesium (NH4+:Mg2+ of 1:3). The operating time was 40 min. Different pretreatments were tested prior to the biomethanization experiments, struvite precipitation, ultrasound and a combination of both pretreatments. The application of ultrasound (with an energy input of 218 kJ L−1) and struvite precipitation (NH4+:Mg2+ of 1:3) increased the methane content in the biogas by 82% and reduced hydraulic retention time by 28%, when compared to the anaerobic co-digestion assays without pretreatment. The hydrolytic pretreatment increased the bioavailability of nitrogen by 5%, thus enhancing the removal efficiency of ammonium nitrogen by 20%. Consequently, an increase in the carbon to nitrogen ratio was observed, favoring the methanogenesis process.

Performance Stability of Small Biological Chemical Treatment Plants

1990 ◽  
Vol 22 (3-4) ◽  
pp. 275-282
Author(s):  
R. Storhaug
Keyword(s):  
Activated Sludge ◽  
Chemical Treatment ◽  
Chemical Precipitation ◽  
Poor Quality ◽  
Precipitation Process ◽  
Chemical Plants ◽  
Effluent Standards ◽  
Main Portion ◽  
Rotating Biological Contactors ◽  
Number Of Treatment

Biological and chemical treatment plants constitute a main portion of the overall number of treatment plants in Norway. The biological and chemical plants are divided into three process groups, simultaneous precipitation and activated sludge, combined precipitation and rotating biological contactors (RBC) and post precipitation and activated sludge. Aluminium sulphate or ferric chloride are the commonly used flocculants in the chemical precipitation process. Effluent data from 174 Norwegian biological chemical treatment plants are evaluated. Compared to the effluent standards for each process group, post precipitation shows the best performance. On an average these plants have the lowest actual utilization of the design capacity. The most important factors that cause the treatment plants not to meet the effluent standards are, poor quality of the sewer system, improper design of the plant and organizational problems. Satisfactory separation of particles, flow equalization and proper operational management, are the basic demands to achieve low effluent concentrations for tot-P and BOD7.

scholarly journals Morphogenesis and evolution mechanisms of bacterially-induced struvite

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Tian-Lei Zhao ◽  
Han Li ◽  
Hao-Fan Jiang ◽  
Qi-Zhi Yao ◽  
Ying Huang ◽  
...  
Keyword(s):  
Time Course ◽  
Carboxyl Groups ◽  
Precipitation Process ◽  
Phosphate Content ◽  
Biomimetic Mineralization ◽  
Struvite Precipitation ◽  
Growth Habits ◽  
Two Stages ◽  
Relevant Work ◽  
Insight Into

AbstractBacteria are able to induce struvite precipitation, and modify struvite morphology, leading to the mineral with various growth habits. However, the relevant work involving the morphogenesis is limited, thereby obstructing our understanding of bacterially mediated struvite mineralization. Here, an actinomycete Microbacterium marinum sp. nov. H207 was chosen to study its effect on struvite morphology. A combination of bacterial mineralization and biomimetic mineralization techniques was adopted. The bacterial mineralization results showed that strain H207 could induce the formation of struvite with grouping structure (i.e., a small coffin-like crystal grown on a large trapezoid-like substrate crystal), and the overgrowth structure gradually disappeared, while the substrate crystal further evolved into coffin-like, and quadrangular tabular morphology with time. The biomimetic experiments with different organic components confirmed that the soluble macromolecules rich in electronegative carboxyl groups secreted by strain H207 dominate the formation of the struvite grouping. The time-course biomimetic experiments with supernatant testified that the increase in pH and NH4+ content promoted the evolution of crystal habits. Moreover, the evolution process of substrate crystal can be divided into two stages. At the first stage, the crystal grew along the crystallographic b axis. At the later stage, coupled dissolution–precipitation process occurred, and the crystals grew along the corners (i.e., [110] and [1-10] directions). In the case of dissolution, it was also found that the (00-1) face of substrate crystal preferentially dissolved, which results from the low initial phosphate content and high PO43− density on this face. As a result, present work can provide a deeper insight into bio-struvite mineralization.

Phosphorus removal from aqueous solution using a novel granular material developed from building waste

2017 ◽  
Vol 75 (6) ◽  
pp. 1500-1511 ◽  
Author(s):  
Shengjiong Yang ◽  
Pengkang Jin ◽  
Xiaochang C. Wang ◽  
Qionghua Zhang ◽  
Xiaotian Chen
Keyword(s):  
Granular Material ◽  
Chemical Precipitation ◽  
Phosphate Removal ◽  
Precipitation Process ◽  
Order Kinetic ◽  
Solution Ph ◽  
Experimental Conditions ◽  
Removal Capacity ◽  
Order Kinetic Model ◽  
Pseudo Second Order

In this study, a granular material (GM) developed from building waste was used for phosphate removal from phosphorus-containing wastewater. Batch experiments were executed to investigate the phosphate removal capacity of this material. The mechanism of removal proved to be a chemical precipitation process. The characteristics of the material and resulting precipitates, the kinetics of the precipitation and Ca2+ liberation processes, and the effects of dosage and pH were investigated. The phosphate precipitation and Ca2+ liberation processes were both well described by a pseudo-second-order kinetic model. A maximum precipitation capacity of 0.51 ± 0.06 mg g−1 and a liberation capacity of 6.79 ± 0.77 mg g−1 were measured under the experimental conditions. The processes reached equilibrium in 60 min. The initial solution pH strongly affected phosphate removal under extreme conditions (pH <4 and pH >10). The precipitates comprised hydroxyapatite and brushite. This novel GM can be considered a promising material for phosphate removal from wastewater.

scholarly journals Recovery Ion Hg2+ dari Limbah Cair Industri Penambangan Emas Rakyat dengan Metode Presipitasi Sulfida dan Hidroksida

2018 ◽  
Vol 12 (1) ◽  
pp. 23
Author(s):  
Ilma Fadlilah ◽  
Agus Prasetya ◽  
Panut Mulyono
Keyword(s):  
Gold Mining ◽  
Mercury Level ◽  
Liquid Waste ◽  
Treatment Method ◽  
Chemical Precipitation ◽  
Precipitation Method ◽  
Precipitation Process ◽  
Sulphide Precipitation ◽  
Slow Mixing ◽  
Precipitation Formation

Unlicensed gold mining activities (PETI) using mercury (Hg) as a gold element binder is called the amalgamation process. Mercury is a heavy metal toxic. The use of mercury can potentially cause pollution in environment, especially the aquatic environment. For overcoming the heavy metals mercury in liquid waste, it needs an alternative wastewater treatment method called chemical precipitation. This study is aimed to recover Hg2+ ions from liquid wastes by using sulphide precipitation and hydroxide methods. This research studied the effect of pH on Hg ions which is deposited in the precipitation process and found out the rate of Hg precipitation formation. Precipitation was done by using sodium sulphide (Na2S) 0.3 M and Ca(OH)2 0.004 M as a precipitation agent with rapid mixing speed for about 200 rpm for 3 minutes and continued with slow mixing for about 40 rpm for 30 minutes. Then, just let the liquid sample be for 24 hours to precipate the precipitate formed. The results show that precipitation method by using a Na2S solution can decrease the content of Hg in HgCl2 synthetic waste. An optimum  mass of HgS precipitate of  0,0458 g was achieved pH 9 for 200 mL of wastewater liquid with a removal efficiency percentage up to 99.81%. The concentration of mercury can be derived from 130 ppm to 0.25 ppm. The rate of formation of HgS precipitate was obtained 0.0004g/ hour. While, hydroxide precipitation method can decrease mercury level up to 90,11% at pH 12 and mass of Hg (OH)2 precipitate obtained is 0,2784 g. However, the result of EDX analysis of the precipitate of Hg (OH)2 shows that the content of Hg precipitate is just 0.281%.

scholarly journals Evaluating the Impacts of ACP Management on the Energy Performance of Hydrothermal Liquefaction via Nutrient Recovery

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 729 ◽  
Author(s):  
Sarah Bauer ◽  
Fangwei Cheng ◽  
Lisa Colosi
Keyword(s):  
Life Cycle ◽  
Energy Performance ◽  
Hydrothermal Liquefaction ◽  
Liquid Fuels ◽  
Precipitation Process ◽  
Net Energy ◽  
Modeling Framework ◽  
Energy Return On Investment ◽  
Theoretical Yield ◽  
Struvite Precipitation

Hydrothermal liquefaction (HTL) is of interest in producing liquid fuels from organic waste, but the process also creates appreciable quantities of aqueous co-product (ACP) containing high concentrations of regulated wastewater pollutants (e.g., organic carbon, nitrogen (N), and phosphorus (P)). Previous literature has not emphasized characterization, management, or possible valorization of ACP wastewaters. This study aims to evaluate one possible approach to ACP management via recovery of valuable scarce materials. Equilibrium modeling was performed to estimate theoretical yields of struvite (MgNH4PO4·6H2O) from ACP samples arising from HTL processing of selected waste feedstocks. Experimental analyses were conducted to evaluate the accuracy of theoretical yield estimates. Adjusted yields were then incorporated into a life-cycle energy modeling framework to compute energy return on investment (EROI) for the struvite precipitation process as part of the overall HTL life-cycle. Observed struvite yields and residual P concentrations were consistent with theoretical modeling results; however, residual N concentrations were lower than model estimates because of the volatilization of ammonia gas. EROI calculations reveal that struvite recovery is a net-energy producing process, but that this benefit offers little to no improvement in EROI performance for the overall HTL life-cycle. In contrast, corresponding economic analysis suggests that struvite precipitation may be economically appealing.

Optimization of Nickel Removal from Electroless Plating Industry Wastewater using Response Surface Methodology

2014 ◽  
Vol 67 (4) ◽  
Author(s):  
Nor Azimah Ahmad ◽  
Mohd Ariffin Abu Hassan ◽  
Zainura Zainon Noor ◽  
Abdullahi Mohammed Evuti ◽  
Jibrin Mohammed Danlami
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Chemical Precipitation ◽  
Precipitation Process ◽  
Jar Test ◽  
Coagulant Dosage ◽  
Nickel Removal ◽  
Optimum Ph

Optimum pH and coagulant dosage for chemical precipitation in wastewater treatment plants is conventionally obtained through repeated jar test. In this research, optimization of the performance of polyacrylamide in the treatment of industrial wastewater was carried out using response surface methodology. The individual linear and quadratic effect of coagulant dosage and pH on the degree of removals of nickel, total suspended solids, Chemical Oxygen Demand and turbidity were investigated. The optimum pH and polyacrylamide dosage were found to be 10.5 and 1.6 ml/L respectively and the optimum percentage nickel removal was 96.9%. The model used in predicting the precipitation process gave a good fit with the experimental variables and hence the suitability of response surface methodology for the optimization of polyacrylamide performance.

Sign in / Sign up

Export Citation Format

Share Document