scholarly journals A Sustainable Approach to the Low-Cost Recycling of Waste Glass Fibres Composites towards Circular Economy

2020 ◽  
Vol 12 (2) ◽  
pp. 641 ◽  
Author(s):  
Omid Zabihi ◽  
Mojtaba Ahmadi ◽  
Chao Liu ◽  
Roya Mahmoodi ◽  
Quanxiang Li ◽  
...  
Keyword(s):  
Microwave Irradiation ◽  
End Of Life ◽  
Epoxy Polymer ◽  
Irradiation Time ◽  
Low Cost ◽  
Chemical Oxidation ◽  
Reinforced Polymers ◽  
Practical Applications ◽  
Low Energy Consumption ◽  
One Step

For practical applications, both environmental and economic aspects are highly required to consider in the development of recycling of fibre reinforced polymers (FRPs) encountering their end-of-life. Here, a sustainable, low cost, and efficient approach for the recycling of the glass fibre (GF) from GF reinforced epoxy polymer (GFRP) waste is introduced, based on a microwave-assisted chemical oxidation method. It was found that in a one-step process using microwave irradiation, a mixture of hydrogen peroxide (H2O2) as a green oxidiser and tartaric acid (TA) as a natural organic acid could be used to decompose the epoxy matrix of a waste GFRP up to 90% yield. The recycled GFs with ~92.7% tensile strength, ~99.0% Young’s modulus, and ~96.2% strain-to-failure retentions were obtained when compared to virgin GFs (VGFs). This short microwave irradiation time using these green and sustainable recycling solvents makes this a significantly low energy consumption approach for the recycling of end-of-life GFRPs.

Microwave-Irradiated Preparation of Super Absorbent Resin by Graft Copolymerization of Starch and Acrylic Acid

2011 ◽  
Vol 291-294 ◽  
pp. 1335-1338
Author(s):  
Da Biao Zhao
Keyword(s):  
Acrylic Acid ◽  
Microwave Irradiation ◽  
Graft Copolymerization ◽  
Irradiation Time ◽  
Low Cost ◽  
Power Level ◽  
Conventional Heating ◽  
Simple Process ◽  
One Step ◽  
Microwave Power Level

Graft copolymerization of acrylic acid(AA) on starch to prepare super absorbent resin (SAR) under microwave irradiation were investigated using N,N-methylene bis-acrylamide as crosslinker and potassium persulfate as initiator. The influences of the amount of initiator and crosslinker, neutralization degree of acrylic acid(AA), ratio of starch to AA, microwave power level and irradiation time on the distilled water absorption amount of resin were investigated. The results indicated that it only needed 4min under the microwave level of 231W to obtain the resin with the maximum absorption amount of 1110g×g-1, under the conditions that 0.3wt% initiator, 0.02wt% crosslinker, 60% neutralization degree of acrylic acid, the ratio of starch to acrylic acid of 0.25. Under microwave irradiation, the synthesis and drying of super absorbent resin could be completed at one step without nitrogen. Compared to conventional heating method, the methods had the striking advantages of short reaction time, simple process and low cost.

scholarly journals Microwave-assisted Synthesis of Hexagonal Gold Nanoparticles Reduced by Organosilane (3-Mercaptopropyl)trimethoxysilane

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1680 ◽  
Author(s):  
Kwok Wei Shah ◽  
Long Zheng
Keyword(s):  
Electron Microscopy ◽  
Gold Nanoparticles ◽  
Microwave Irradiation ◽  
Irradiation Time ◽  
Chemical Reduction ◽  
Microwave Assisted Synthesis ◽  
Au Nps ◽  
One Step ◽  
The Impact ◽  
First Time

A novel synthesis of hexagonal gold nanoparticles (Au NPs) via hydrolyzed organosilane (3-mercaptopropyl)trimethoxysilane (MPTMS) using an ultrafast and environmentally friendly method is presented in this study. For the first time, organosilane MPTMS is used for chemical reduction of auric acid under ultrafast microwave irradiation. To the best of our knowledge, the use of organosilane for the synthesis of Au NPs has not been reported. The entire one-step process is convenient, rapid and cost-effective, as well as eco-friendly under alcohol-free aqueous media. Different characterization methods were carried out to investigate the properties of synthesized gold nanoparticles. transmission electron microscopy and scanning electron microscopy were used to investigate the morphology of as-synthesized Au NPs, while X-ray powder diffraction was applied to obtain the crystalline nature. Nuclear magnetic resonance was used to track the hydrolysis of organosilane MPTMS, which is employed for the first time as a reducing agent for the synthesis of Au NPs. The impact from microwave irradiation time and power, as well as the catalytic property of as-synthesized Au NPs, was investigated via ultraviolet–visible spectroscopy. The as-synthesized products include gold nanohexagon and two-dimensional hexagonal gold nanoplatelets, both of which are single-crystal with (1 1 1) planes as basal surfaces. From UV-vis spectra, it is found that the facile water-based fabrication of hexagonal Au NPs began within seconds of microwave irradiation and the size growth increased with the microwave power and time. Moreover, the efficient reduction of 4-nitrophenol to 4-aminophenol in the presence of as-synthesized Au NPs was observed, exhibiting a remarkable catalytic activity. The present simple, rapid and convenient one-step microwave process possess high scalability and useful for future applications such as catalysis, medical, biological, plasmonic sensors and electronics.

scholarly journals A Modified Preparation of Cellulosic-Absorbent Resin for Cu2+ Removal under Microwave Irradiation

2020 ◽  
Vol 2020 ◽  
pp. 1-6
Author(s):  
Jing Shu ◽  
Dabiao Zhao ◽  
Lili Li
Keyword(s):  
Microwave Irradiation ◽  
Low Cost ◽  
Power Level ◽  
Crosslinking Agent ◽  
Sodium Thiosulfate ◽  
Redox System ◽  
Preparation Period ◽  
One Step ◽  
Short Time ◽  
Microwave Power Level

The absorbent resin for Cu2+ removal was prepared under microwave irradiation through grafting acrylamide (AM) and acrylic acid (AA) to cellulose. The initiator is a kind of redox system composed of potassium persulfate/sodium thiosulfate. The crosslinking agent is N,N′-methylene bisacrylamide. The optimal reaction conditions are as follows: the ratio of AA to cellulose is 10 : 1, initiator to AA is 0.65 wt%, crosslinking agent to AA is 1.0 wt%, neutralization degree of AA is 75%, microwave power level is 320 W, and time is 300 s. The maximum absorption capability of the resin is 65 mg·g−1. Different from previous studies, the reaction was carried out without the protection of nitrogen and troublesome posttreatment. The product was obtained directly by one-step synthesis without purification and drying of the crude product. The pollution and cost caused by organic solvent are avoided, and the whole preparation period is shortened deeply. Moreover, the time of absorption equilibrium is shorter. In a word, the preparation in this paper has the obvious advantages, such as simple process, short time, no pollution, low-energy, and low-cost.

Dual Nickel/Palladium-Catalyzed Reductive Cross-Coupling Reactions Between Two Phenol Derivatives

2020 ◽  
Author(s):  
Baojian Xiong ◽  
Yue Li ◽  
Yin Wei ◽  
Søren Kramer ◽  
Zhong Lian
Keyword(s):  
Functional Group ◽  
Low Cost ◽  
Cross Coupling ◽  
Coupling Reactions ◽  
Phenol Derivatives ◽  
Cross Coupling Reactions ◽  
Palladium Catalyzed ◽  
One Step ◽  
Aryl Tosylates ◽  
Low Sensitivity

Cross-coupling between substrates that can be easily derived from phenols is highly attractive due to the abundance and low cost of phenols. Here, we report a dual nickel/palladium-catalyzed reductive cross-coupling between aryl tosylates and aryl triflates; both substrates can be accessed in just one step from readily available phenols. The reaction has a broad functional group tolerance and substrate scope (>60 examples). Furthermore, it displays low sensitivity to steric effects demonstrated by the synthesis of a 2,2’disubstituted biaryl and a fully substituted aryl product. The widespread presence of phenols in natural products and pharmaceuticals allow for straightforward late-stage functionalization, illustrated with examples such as Ezetimibe and tyrosine. NMR spectroscopy and DFT calculations indicate that the nickel catalyst is responsible for activating the aryl triflate, while the palladium catalyst preferentially reacts with the aryl tosylate.

Surface Modification of Poly(Vinylchloride) for Manufacturing Advanced Catheters

2020 ◽  
Vol 27 (10) ◽  
pp. 1616-1633 ◽  
Author(s):  
Oana Cristina Duta ◽  
Aurel Mihail Ţîţu ◽  
Alexandru Marin ◽  
Anton Ficai ◽  
Denisa Ficai ◽  
...  
Keyword(s):  
Surface Modification ◽  
Chemical Modification ◽  
Medical Devices ◽  
Low Cost ◽  
Physical And Mechanical Properties ◽  
Polymeric Materials ◽  
Modern Medicine ◽  
Structural Failure ◽  
Chemical Grafting ◽  
One Step

Polymeric materials, due to their excellent physicochemical properties and versatility found applicability in multiples areas, including biomaterials used in tissue regeneration, prosthetics (hip, artificial valves), medical devices, controlled drug delivery systems, etc. Medical devices and their applications are very important in modern medicine and the need to develop new materials with improved properties or to improve the existent materials is increasing every day. Numerous reasearches are activated in this domain in order to obtain materials/surfaces that does not have drawbacks such as structural failure, calcifications, infections or thrombosis. One of the most used material is poly(vinylchloride) (PVC) due to its unique properties, availability and low cost. The most common method used for obtaining tubular devices that meet the requirements of medical use is the surface modification of polymers without changing their physical and mechanical properties, in bulk. PVC is a hydrophobic polymer and therefore many research studies were conducted in order to increase the hydrophilicity of the surface by chemical modification in order to improve biocompatibility, to enhance wettability, reduce friction or to make lubricious or antimicrobial coatings. Surface modification of PVC can be achieved by several strategies, in only one step or, in some cases, in two or more steps by applying several techniques consecutively to obtain the desired modification / performances. The most common processes used for modifying the surface of PVC devices are: plasma treatment, corona discharge, chemical grafting, electric discharge, vapour deposition of metals, flame treatment, direct chemical modification (oxidation, hydrolysis, etc.) or even some physical modification of the roughness of the surface.

scholarly journals Chemical Modification of Combusted Coal Gangue for U(VI) Adsorption: Towards a Waste Control by Waste Strategy

2021 ◽  
Vol 13 (15) ◽  
pp. 8421
Author(s):  
Yuan Gao ◽  
Jiandong Huang ◽  
Meng Li ◽  
Zhongran Dai ◽  
Rongli Jiang ◽  
...  
Keyword(s):  
Structural Analysis ◽  
High Efficiency ◽  
Low Cost ◽  
Chemical Activation ◽  
Cost Effective ◽  
Coal Gangue ◽  
Order Kinetic ◽  
Practical Applications ◽  
Detailed Structural Analysis ◽  
Alkaline Conditions

Uranium mining waste causes serious radiation-related health and environmental problems. This has encouraged efforts toward U(VI) removal with low cost and high efficiency. Typical uranium adsorbents, such as polymers, geopolymers, zeolites, and MOFs, and their associated high costs limit their practical applications. In this regard, this work found that the natural combusted coal gangue (CCG) could be a potential precursor of cheap sorbents to eliminate U(VI). The removal efficiency was modulated by chemical activation under acid and alkaline conditions, obtaining HCG (CCG activated with HCl) and KCG (CCG activated with KOH), respectively. The detailed structural analysis uncovered that those natural mineral substances, including quartz and kaolinite, were the main components in CCG and HCG. One of the key findings was that kalsilite formed in KCG under a mild synthetic condition can conspicuous enhance the affinity towards U(VI). The best equilibrium adsorption capacity with KCG was observed to be 140 mg/g under pH 6 within 120 min, following a pseudo-second-order kinetic model. To understand the improved adsorption performance, an adsorption mechanism was proposed by evaluating the pH of uranyl solutions, adsorbent dosage, as well as contact time. Combining with the structural analysis, this revealed that the uranyl adsorption process was mainly governed by chemisorption. This study gave rise to a utilization approach for CCG to obtain cost-effective adsorbents and paved a novel way towards eliminating uranium by a waste control by waste strategy.

scholarly journals Preparation and photocatalytic performance of metallic Nb0.9Ta0.1S2/2D-C3N4 composite

2020 ◽  
Vol 1 (1) ◽  
Author(s):  
Hanxiang Chen ◽  
Jianjian Yi ◽  
Zhao Mo ◽  
Yanhua Song ◽  
Wenshu Yang ◽  
...  
Keyword(s):  
Separation Efficiency ◽  
Low Cost ◽  
Metal Sulfide ◽  
Electron Hole ◽  
Practical Applications ◽  
Energy And Environment ◽  
Photocatalytic Application ◽  
Light Utilization ◽  
Ternary Metal ◽  
Key Issues

Abstract Photocatalysis technology has potential application in the field of energy and environment. How to expand visible light utilization and promote the separation efficiency of the carriers are the key issues for the high active photocatalysts preparation and future practical applications. In this work, a ternary metal sulfide Nb0.9Ta0.1S2 was prepared and used as an electron collector in the photocatalytic application. As a result, the generated electrons are quickly transferred to the surface of the composite to participate in the reaction. It was demonstrated that the photocatalytic activity of 2D-C3N4 was enhanced after the modification of Nb0.9Ta0.1S2. The Nb0.9Ta0.1S2/2D-C3N4 composite material was synthesized by solvothermal method. The composition of 5% Nb0.9Ta0.1S2/2D-C3N4 showed the highest H2 evolution rate of 1961.6 μmolg−1h−1, which was 6.6 times that of 2D-C3N4. The 15% Nb0.9Ta0.1S2/2D-C3N4 exhibited the best activity in Rhodamine B degradation rate of 97% in 2 h, which is 50% higher than that of 2D-C3N4. Nb0.9Ta0.1S2/2D-C3N4 can be used as electron trap to promote the effective separation of electron–hole pairs. This work provides benchmarks in exploring low-cost and efficient cocatalyst.

scholarly journals Magnetic iron oxide/clay nanocomposites for adsorption and catalytic oxidation in water treatment applications

2020 ◽  
Vol 18 (1) ◽  
pp. 1148-1166
Author(s):  
Ganjar Fadillah ◽  
Septian Perwira Yudha ◽  
Suresh Sagadevan ◽  
Is Fatimah ◽  
Oki Muraza
Keyword(s):  
Iron Oxide ◽  
Water Treatment ◽  
Photocatalytic Oxidation ◽  
Low Cost ◽  
Synthesis Method ◽  
Chemical Oxidation ◽  
Magnetic Iron Oxide ◽  
Oxidation Processes ◽  
Recent Developments ◽  
Physical And Chemical

AbstractPhysical and chemical methods have been developed for water and wastewater treatments. Adsorption is an attractive method due to its simplicity and low cost, and it has been widely employed in industrial treatment. In advanced schemes, chemical oxidation and photocatalytic oxidation have been recognized as effective methods for wastewater-containing organic compounds. The use of magnetic iron oxide in these methods has received much attention. Magnetic iron oxide nanocomposite adsorbents have been recognized as favorable materials due to their stability, high adsorption capacities, and recoverability, compared to conventional sorbents. Magnetic iron oxide nanocomposites have also been reported to be effective in photocatalytic and chemical oxidation processes. The current review has presented recent developments in techniques using magnetic iron oxide nanocomposites for water treatment applications. The review highlights the synthesis method and compares modifications for adsorbent, photocatalytic oxidation, and chemical oxidation processes. Future prospects for the use of nanocomposites have been presented.

scholarly journals A Survey on Deep Learning Based Methods and Datasets for Monocular 3D Object Detection

Electronics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 517
Author(s):  
Seong-heum Kim ◽  
Youngbae Hwang
Keyword(s):  
Deep Learning ◽  
Object Detection ◽  
Low Cost ◽  
Detection Methods ◽  
Future Research ◽  
3D Object ◽  
Practical Applications ◽  
Depth Sensors ◽  
Significant Research ◽  
3D Object Detection

Owing to recent advancements in deep learning methods and relevant databases, it is becoming increasingly easier to recognize 3D objects using only RGB images from single viewpoints. This study investigates the major breakthroughs and current progress in deep learning-based monocular 3D object detection. For relatively low-cost data acquisition systems without depth sensors or cameras at multiple viewpoints, we first consider existing databases with 2D RGB photos and their relevant attributes. Based on this simple sensor modality for practical applications, deep learning-based monocular 3D object detection methods that overcome significant research challenges are categorized and summarized. We present the key concepts and detailed descriptions of representative single-stage and multiple-stage detection solutions. In addition, we discuss the effectiveness of the detection models on their baseline benchmarks. Finally, we explore several directions for future research on monocular 3D object detection.

scholarly journals Effects of microwave irradiation on the moisture content of various wood chip fractions obtained from different tree species

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Monika Aniszewska ◽  
Krzysztof Słowiński ◽  
Ewa Tulska ◽  
Witold Zychowicz
Keyword(s):  
Moisture Content ◽  
Microwave Irradiation ◽  
Microwave Power ◽  
Irradiation Time ◽  
Initial Moisture Content ◽  
Radiant Energy ◽  
Wood Chip ◽  
Wood Chips ◽  
Chip Size ◽  
Drying Rates

AbstractThe paper proposes the use of microwave irradiation to lower the initial moisture content of wood chips. The study involved willow and fir chips fractionated by means of a sieve separator and unfractionated ash chips. The wood chips were exposed to a constant microwave power of 800 W for 30 s, 60 s, 120 s and 180 s. The chips were weighed before and after irradiation to measure loss of moisture. It was found that the decline in moisture content increased with wood chip size for a given irradiation time and microwave power. The initial moisture content of wood chips was not found to significantly affect loss of moisture as the drying rates of wood chips with higher and lower moisture content exposed to microwaves were not statistically different. The results showed that irradiation intensity increased with the time of exposure to microwaves and unit radiant energy per unit of evaporated moisture decreased with increasing wood chip size in the 3.15–31.50 mm range.

Sign in / Sign up

Export Citation Format

Share Document