scholarly journals A 28 GHz 2 × 2 Antenna Array with 10 Beams Using Passive SPDT Switch Beamforming Network

Sensors ◽  
2021 ◽  
Vol 21 (21) ◽  
pp. 7138
Author(s):  
Firas Abdul Abdul Ghani ◽  
Amir Mohsen Ahmadi Najafabadi ◽  
Heba Saleh ◽  
Murat Kaya Kaya Yapici ◽  
Ibrahim Tekin
Keyword(s):  
Antenna Array ◽  
Beam Steering ◽  
Ground Plane ◽  
Antenna Design ◽  
Main Beam ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Compact Size ◽  
Dual Polarized ◽  
Switched Beams

In this paper, a dual-polarized four-port 2 × 2 series fed antenna array operating at 28 GHz with beam-switching capability is proposed. The antenna array uses a simple passive beamforming network to switch the main beam. The presented antenna design is suitable for 5G user equipment and high data rates applications by which it has a compact size with low cost and complexity. The size of the antenna is 37.2 × 37.2 mm2 including the ground plane, and it produces 10 different switched beams by using only two simple 3 dB/90∘ couplers which create the required amplitudes and phase excitations for the antenna elements. A one-port simple feeding mechanism including Peregrine PE42525 SPDT switch modules and a power divider is used to generate and measure the 10 switched beams. The antenna design is implemented on a two-layer 0.203 mm thick low-loss (tanδ = 0.0027) Rogers 4003C substrate, and it has a measured 10 dB impedance bandwidth of 4 GHz (14.3%, from 26 GHz to 30 GHz) for all ports. Measured peak isolation between any dual-polarized ports of the antenna is better than 30 dB. The antenna has an average measured realized gain of 8.9 dBi and around 10 dB side lobe level (SLL) for all beams. The antenna has 3-dB coverage of 80∘ to 90∘ in 2D space and it has a maximum of ±26∘ beam-steering angle. The antenna is designed and simulated using Ansys HFSS and fabricated using regular PCB processing.

scholarly journals CPW-fed circularly-polarized antenna array with high front-to-back ratio and low-profile

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 651-655 ◽  
Author(s):  
Yilin Liu ◽  
Kama Huang
Keyword(s):  
Antenna Array ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Axial Ratio ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Feeding Method ◽  
Circularly Polarized ◽  
Low Profile ◽  
Novel Design

Abstract A novel design of a coplanar waveguide (CPW) feed antenna array with circular polarization (CP) and a high front-to-back ratio is described. The proposed CP array is achieved by using a compact CPW–slotline transition network etched in the ground plane. The measured results show that this kind of feeding method can improve the impedance bandwidth, as well as the axial ratio bandwidth of the CP antenna array and provide adequate gain. The proposed array can achieve a 6.08% impedance bandwidth and a 4.10% CP bandwidth. Details of the antenna design and experimental results are presented and discussed.

scholarly journals Design of Transparent Antenna for 5G Wireless Applications

Proceedings ◽  
2020 ◽  
Vol 63 (1) ◽  
pp. 54
Author(s):  
Sanae Azizi ◽  
Laurent Canale ◽  
Saida Ahyoud ◽  
Georges Zissis ◽  
Adel Asselman
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Light Weight ◽  
Frequency Bandwidth ◽  
Frequency Range ◽  
Wireless Applications ◽  
Compact Size

This paper presents the design of a compact size band patch antenna for 5G wireless communications. This wideband antenna was designed on a glass substrate (12 × 11 × 2 mm3) and is optically transparent and compact. It consists of a radiation patch and a ground plane using AgHT-8 material. The antenna design comprises rectangular shaped branches optimized to attain the wideband characteristics. The calculated impedance bandwidth is 7.7% covering the frequency range of 25 to 27 GHz. A prototype of the antenna and various parameters such as return loss plot, gain plot, radiation pattern plot, and voltage standing wave ratio (VSWR) are presented and discussed. The simulated results of this antenna show that it is well suited for future 5G applications because of its transparency, flexibility, light weight, and wide achievable frequency bandwidth near the millimeter wave frequency band.

scholarly journals Dual-polarized antenna design integrated with metasurface and partially reflective surface for 5G communication

2020 ◽  
Vol 7 ◽  
pp. 3
Author(s):  
Zhilong Li ◽  
Yajie Mu ◽  
Jiaqi Han ◽  
Xiaohe Gao ◽  
Long Li
Keyword(s):  
Antenna Array ◽  
Ground Plane ◽  
Side Lobe ◽  
Base Station ◽  
Side Lobe Level ◽  
Reflective Surface ◽  
Varactor Diodes ◽  
Fabry Perot ◽  
5G Communication ◽  
Dual Polarized

A design of electrical down-tilt dual-polarized base station antenna array (BSAA) for 5G communication applications is presented in this paper, which is realized by integrating with reconfigurable reflective metasurface and partially reflective surface (PRS). By controlling the varactor diodes which are inserted into the reflective elements, we can adjust the mainlobe direction of BSAA. Moreover, the PRS over the array is utilized to construct Fabry-Perot (FP) cavity with reflective metasurface and ground plane. Based on this design approach, a 1 × 6 dual-polarized BSAA operating from 3.4 GHz to 3.6 GHz is designed and fabricated. Simulated and measured results show that the gain is enhanced about 2.56 dB by PRS while side lobe level (SLL) is less than −20 dB. The mainlobe of the antenna array can be adjusted accurately within ±5° for beam down-tilt. The cross polarization discrimination (XPD) is less than −40 dB.

scholarly journals A UWB Antenna Array Integrated with Multimode Resonator Bandpass Filter

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 607
Author(s):  
Sharif Ahmed ◽  
Tan Kim Geok ◽  
Mohamad Yusoff Alias ◽  
Ferdous Hossain ◽  
Hussein Alsariera ◽  
...  
Keyword(s):  
Antenna Array ◽  
Bandpass Filter ◽  
Ground Plane ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Uwb Antenna ◽  
Compact Size ◽  
Measurement Results ◽  
Uwb Applications ◽  
Array Performance

This paper presents a novel design of a modified ultrawideband (UWB) antenna array integrated with a multimode resonator bandpass filter. First, a single UWB antenna is modified and studied, using a P-shape radiated patch instead of a full elliptical patch, for wide impedance bandwidth and high realized gain. Then, a two-element UWB antenna array is developed based on this modified UWB antenna with an inter-element spacing of 0.35 λL, in which λL is the free space wavelength at the lower UWB band edge of 3.1 GHz, compared to 0.27 λL of a reference UWB antenna array designed using a traditional elliptical patch shape. The partial ground plane is designed with a trapezoidal angle to enhance matching throughout the UWB frequency range. The mutual coupling reduction of a modified UWB antenna array enhances the reflection coefficient, bandwidth, and realized gain, maintaining the same size of 1.08 λ0 × 1.08 λ0 × 0.035 λ0 at 6.5 GHz center frequency as that of the reference UWB antenna array. The UWB antenna array performance is investigated at different inter-element spacing distances between the radiated elements. To add filtering capability to the UWB antenna array and eliminate interference from the out-of-band frequencies, a multimode resonator (MMR) bandpass filter (BPF) is incorporated in the feedline while maintaining a compact size. The measurement results showed a close agreement with simulated results. The proposed UWB filtering antenna array design achieved a wide fractional bandwidth of more than 109.87%, a high realized gain of more than 7.4 dBi, and a compact size of 1.08 λ0 × 1.08 λ0 × 0.035 λ0 at 6.5 GHz center frequency. These advantages make the proposed antenna suitable for UWB applications such as indoor tracking, radar systems and positioning applications.

Light-weight wideband antenna array with low sidelobes for SAR applications

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Reza Kazemi ◽  
Mohsen Fallah ◽  
Bijan Abbasi ◽  
Seyyed Hossein MohseniArmaki
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Linear Array ◽  
Side Lobe ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Antenna Element ◽  
Light Weight ◽  
Content Type ◽  
Compact Size

Purpose The purpose of this study is to achieve the low-cost, light-weight and compact antenna array with wide bandwidth and low side lobe levels for synthetic aperture radar (SAR) applications in Ku frequency band. Design/methodology/approach A compact design of a rectangular microstrip patch antenna array using multilayered dielectric structure is presented in Ku-band for advanced broadband SAR systems. In this design, stepped pins are used to connect the microstrip feed lines to the radiating patches. Findings The simulation and fabrication results of the multilayered antenna and a 1×16-element linear array of the antenna with Taylor amplitude distribution in the feeding network are presented. The antenna element has a 10-dB impedance bandwidth of more than 26%, and the linear array shows reduction in bandwidth percentage (about 15.4%). Thanks to Taylor amplitude tapering, the side lobe level (SLL) of the array is lower than −24 dB. The maximum measured gains of the antenna element and the linear array are 7 and 19.2 dBi at the center frequency, respectively. Originality/value In the communication systems, a high gain narrow beamwidth radiation pattern achieved by an array of multiple antenna elements with optimized spacing is a solution to overcome the path loss, atmospheric loss, polarization loss, etc. Also, wideband characteristics and compact size are desirable in satellite and SAR systems. This paper provides the combination of these features by microstrip structures.

scholarly journals Triangular Slot-Loaded Wideband Planar Rectangular Antenna Array for Millimeter-Wave 5G Applications

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 778
Author(s):  
Iftikhar Ahmad ◽  
Houjun Sun ◽  
Umair Rafique ◽  
Zhang Yi
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Ground Plane ◽  
Simulated Data ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Antenna ◽  
Rectangular Patch ◽  
Half Power

This paper presents a design of a triangular slot-loaded planar rectangular antenna array for wideband millimeter-wave (mm-wave) 5G communication systems. The proposed array realizes an overall size of 35.5 × 14.85 mm2. To excite the array elements, a four-way broadband corporate feeding network was designed and analyzed. The proposed array offered a measured impedance bandwidth in two different frequency ranges, i.e., from 23 to 24.6 GHz and from 26 to 45 GHz. The single-antenna element of the array consists of a rectangular patch radiator with a triangular slot. The partial ground plane was used at the bottom side of the substrate to obtain a wide impedance bandwidth. The peak gain in the proposed array is ≈12 dBi with a radiation efficiency of >90%. Furthermore, the array gives a half-power beamwidth (HPBW) of as low as 12.5°. The proposed array has been fabricated and measured, and it has been observed that the measured results are in agreement with the simulated data.

Arrow Patch-Slot Antenna for 5G Lower Frequency Band Communications

2021 ◽  
Vol 35 (11) ◽  
pp. 1418-1419
Author(s):  
Yuhao Feng ◽  
Yiming Chen ◽  
Atef Elsherbeni ◽  
Khalid Alharbi
Keyword(s):  
Antenna Arrays ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Base Stations ◽  
Slot Antenna ◽  
Main Beam ◽  
Antenna Element ◽  
Single Element ◽  
Rectangular Slot ◽  
Compact Size

A compact size arrow shaped patch in a rectangular slot antenna is designed for 5G communications in the lower 3 to 6 GHz band. The antenna element is fed through a coplanar waveguide with partial ground plane for better impedance matching with 50 Ohms across the entire band. The maximum gain of a single element is 3.8 dB at 3.7 GHz, while for linear arrays of 5 and 15 elements with uniform excitation the maximum gains are 10.9 dB and 16 dB, respectively. The 5 and 15 elements arrays provide scanning range with no significant degradation of the main beam up to 30˚ and 45˚, respectively. The properties of this antenna element makes it suitable for 5G wireless mobile devices and miniaturized base stations antenna arrays.

scholarly journals A Novel High Gain Monopole Antenna Array for 60 GHz Millimeter-Wave Communications

2020 ◽  
Vol 10 (13) ◽  
pp. 4546
Author(s):  
Tarek S. Mneesy ◽  
Radwa K. Hamad ◽  
Amira I. Zaki ◽  
Wael A. E. Ali
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Ground Plane ◽  
High Gain ◽  
Monopole Antenna ◽  
Impedance Bandwidth ◽  
Single Element ◽  
60 Ghz ◽  
Defected Ground Structure ◽  
Element Array

This paper presented the design and implementation of a 60 GHz single element monopole antenna as well as a two-element array made of two 60 GHz monopole antennas. The proposed antenna array was used for 5G applications with radiation characteristics that conformed to the requirements of wireless communication systems. The proposed single element was designed and optimized to work at 60 GHz with a bandwidth of 6.6 GHz (57.2–63.8 GHz) and a maximum gain of 11.6 dB. The design was optimized by double T-shaped structures that were added in the rectangular slots, as well as two external stubs in order to achieve a highly directed radiation pattern. Moreover, ring and circular slots were made in the partial ground plane at an optimized distance as a defected ground structure (DGS) to improve the impedance bandwidth in the desired band. The two-element array was fed by a feed network, thus improving both the impedance bandwidth and gain. The single element and array were fabricated, and the measured and simulated results mimicked each other in both return loss and antenna gain.

Design of a novel triple-band monopole antenna for WLAN/WiMAX MIMO applications in the laptop computer

Circuit World ◽  
2019 ◽  
Vol 45 (4) ◽  
pp. 257-267 ◽  
Author(s):  
Jayshri Sharad Kulkarni ◽  
Raju Seenivasan
Keyword(s):  
Antenna Array ◽  
Cost Effective ◽  
Monopole Antenna ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Laptop Computer ◽  
Content Type ◽  
Laptop Computers ◽  
Triple Band

Purpose This paper aims to present a triple-band monopole antenna design of 0.2-mm thickness with an overall dimension of 21 × 8 mm2 for wireless local area network (WLAN)/worldwide interoperability for microwave access (WiMAX) multiple input and multiple output (MIMO) applications in the laptop computer. Design/methodology/approach It comprises three monopole radiating elements, namely, strip AD (inverted C), strip EG (inverted J) and strip FI (inverted U) along with two rectangular open-end tuning stubs, namely, “m” and “n” of size 1.5 × 0.9 mm2 and 1.8 × 0.9 mm2, respectively. The proposed structure is compact, cost-effective and easy to integrate inside the laptop computers. Findings This structure excites three WLAN (2.4/5.2/5.8 GHz) and three WiMAX (2.3/3.3/5.5 GHz) bands. The proposed antenna array elucidates that it has measured −10dB impedance bandwidth of 11.86 per cent (2.22-2.50) GHz in a lower band (f_l), 6.83 per cent (3.25-3.48) GHz in medium band (f_m) and 16.84 per cent (5.00-5.92) GHz in upper band (f_u). The measured gain and radiation efficiency are above 3.64dBi and 75 per cent, respectively, and isolation better than −20dB. The envelope correlation coefficient (ECC) is less than 0.004. The simulated and measured results are in good concurrence, which confirms the applicability of the proposed antenna array for MIMO applications in the laptop computer. Originality/value The proposed antenna is designed without using vias, reactive elements and matching circuits for excitation of WLAN/WiMAX bands in the laptop computers. The design also does not require any additional ground for mounting the antenna. Further, the antenna array, formed by using the same antenna design, does not need additional isolating elements and is designed in such a way that the system ground itself acts as an isolating element. The proposed antenna has a low profile and is ultra-thin, cost-effective and easy to manufacture and can be easily embedded inside the next-generation laptop computers.

scholarly journals A Novel Coplanar Waveguide-Fed Compact Microstrip Antenna for Future 5G Applications

2020 ◽  
Vol 14 (2) ◽  
pp. 104-110
Author(s):  
Mustafa Berkan Bicer
Keyword(s):  
Microstrip Antenna ◽  
Return Loss ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Antenna Design ◽  
Method Of Moment ◽  
Full Wave ◽  
Compact Size ◽  
Compact Microstrip Antenna ◽  
Acs Algorithm

In this study, a coplanar waveguide-fed compact microstrip antenna design for applications operating at higher 5G bands was proposed. The antenna with the compact size of 8 x 12.2 mm2 on FR4 substrate, having the dielectric constant of 4.3 and the height of 1.55 mm, was considered. The dimensions of the radiating patch and ground plane were optimized with the use of artificial cooperative search (ACS) algorithm to provide the desired return loss performance of the designed antenna. The performance analysis was done by using full-wave electromagnetic package programs based on the method of moment (MoM) and the finite integration technique (FIT). The 10 dB bandwidth for return loss results obtained with the use of the computation methods show that the proposed antenna performs well for 5G applications operating in the 24.25 – 27.50 GHz, 26.50 – 29.50 GHz, 27.50 – 28.35 GHz and 37 – 40 GHz frequency bands.

Sign in / Sign up

Export Citation Format

Share Document