scholarly journals Analysis of Patch Antenna with Broadband Using Octagon Parasitic Patch

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4908
Author(s):  
Sun-Woong Kim ◽  
Ho-Gyun Yu ◽  
Dong-You Choi
Keyword(s):  
Radiation Pattern ◽  
Patch Antenna ◽  
High Gain ◽  
Directional Pattern ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
S Parameter ◽  
Parasitic Patch ◽  
Measurement Results

This paper proposes a novel broadband octagonal patch antenna with parasitic patches. The proposed patch antenna is constructed with four parasitic patches around a central radiating octagonal element. It is illustrated that this arrangement can be used to improve the antenna bandwidth and gain when compared with that of conventional antennas. The proposed patch antenna is very simple, low-profile, and economical. The typical analysis of the proposed antenna is analyzed by the S11(S-parameter), the radiation pattern, and the realized gain. It can achieve an impedance bandwidth of 1.44 GHz and a high gain of 8.56 dBi in the 8.5 GHz band. Furthermore, the proposed antenna shows that the directional pattern and HPBW measurement results of E and H-plane were 70° and 74° at 8.5 GHz, and 74° and 83° at 9 GHz, and 47° and 42° at 9.5 GHz, respectively.

Design of low profile co-axial fed high gain stacked patch antenna for Wi-Fi/WLAN/Wi-Max applications

Frequenz ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Gnanasivam Pachaiyappan ◽  
Parthasarathy Ramanujam
Keyword(s):  
Bottom Layer ◽  
High Gain ◽  
Base Station ◽  
Radiation Efficiency ◽  
Impedance Bandwidth ◽  
Simple Design ◽  
Low Profile ◽  
Parasitic Patch ◽  
Mobile Base Station ◽  
Mobile Base

AbstractIn this article, a simple design of stacked radiating system with enhanced gain, impedance bandwidth, and radiation efficiency for mobile base station application is presented. The proposed antenna consists of a driven patch with a semicircular parasitic patch printed on the bottom layer and five parasitic patches printed on the top layer. The driven patch is feed by a co-axial probe and both the layers are separated in air. The second layer has four truncated circular parasitic patches on one side and one circular patch on the other side to enhance the directive gain acts as a directive reflector. This staked system encompasses some prominent features such as wide bandwidth, good gain, low profile, better radiation efficiency simple design, and integration for the mobile base station. Meanwhile, this configuration exhibits a bandwidth of 2 GHz with the minimized volume is 0.75 λ0 × 0.75 λ0 × 0.08 λ0. Experimentally validated results have an average and peak gain of 10.7 and 12.7 dBi, impedance bandwidth of more than 30.7% for |S11| < −10 dB, and radiation efficiency of above 86%. The proposed stacked radiating system finds its applications in Wi-Fi, WLAN, Wi-Max, Indoor UWB, and Marine Radar applications.

scholarly journals Fully Integrated High Gain S-Band Triangular Slot Antenna for CubeSat Communications

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 156
Author(s):  
Mohamed El Bakkali ◽  
Moulhime El Bekkali ◽  
Gurjot Singh Gaba ◽  
Josep M. Guerrero ◽  
Lavish Kansal ◽  
...  
Keyword(s):  
Radiation Pattern ◽  
Return Loss ◽  
Impedance Matching ◽  
Electronic Devices ◽  
Wide Band ◽  
High Gain ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Fully Integrated ◽  
Low Profile

Among other CubeSat subsystems, Antenna is one of the most important CubeSat components as its design determines all the telecommunication subsystems’ performances. This paper presents a coplanar wave-guide (CPW)-fed equilateral triangular slot antenna constructed and analyzed for CubeSat communications at S-band. The proposed antenna alone presents high gain and ultra-wide band while its radiation pattern is bidirectional at an unlicensed frequency of 2450 MHz. The objective is to use the CubeSat chassis as a reflector for reducing the back-lobe radiation and hence minimizing interferences with electronic devices inside the CubeSat. This leads to a high gain of 8.20 dBi and a unidirectional radiation pattern at an industrial, scientific and mdical (ISM) band operating frequency of 2450 MHz. In addition to that, the presented antenna is low-profile and exhibits high return loss, ultra-wide impedance bandwidth, and good impedance matching at 2450 MHz.

scholarly journals An end-fire low profile patch antenna to work on WiMAX frequencies used for harvesting power supply

2021 ◽  
Vol 10 (5) ◽  
pp. 2678-2685
Author(s):  
Anwer Sabah Mekki ◽  
Siba Monther Yousif ◽  
Bashar Mudhafar Ahmed ◽  
Mustafa Mohammed Jawad
Keyword(s):  
Power Supply ◽  
Patch Antenna ◽  
Fire Retardant ◽  
Wide Band ◽  
High Gain ◽  
Center Frequency ◽  
High Loss ◽  
Low Profile ◽  
Measurement Results ◽  
Good Agreement

In this paper, an end-fire microstrip patch antenna (MPA) is proposed of 3 GHz as a center frequency, designed, simulated, and measured to work on WiMAX frequencies within standard of 802.16e (WiMAX). A high gain ranged between (12.117-13.324) dB, high front to back ratio (F/B) of (35.770) at the center frequency, a wide band of 1.701 GHz, low profile, and semi-ideal voltage standing wave ratio (VSWR) of 1.053 is achieved. The simulation is done using computer simulation technology (CST-MW). The proposed design is based on two Fire-retardant substrates (FR-4) of relative permittivity (ε) 4.3+j0.025 and 1.53 mm thickness for each one, which is considered a high loss material. The measurement results show good agreement with the simulated results. In addition, the design can be used for harvesting power supply from mobile towers. Finally, the proposed design is compared with two other designs in terms of power conversion efficiency and overall size.

High gain low profile wideband dual-layered substrate microstrip antenna based on multiple parasitic elements

2017 ◽  
Vol 10 (4) ◽  
pp. 453-459
Author(s):  
Haixiong Li ◽  
Bozhang Lan ◽  
Jun Ding ◽  
Chenjiang Guo
Keyword(s):  
Reflection Coefficient ◽  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
Layered Substrate ◽  
Measured Impedance ◽  
Peak Gain

In this paper, a high gain broadband low profile microstrip antenna with the dual-layered substrate and four parasitic metal elements is presented. The proposed microstrip antenna is mainly composed of four parts: four circular parasitic metal patches with dual arced breaches, a rectangular metal patch sandwiched between substrates, a square ground plane, and two-square substrates. The circular parasitic elements are the main radiation structure and determine the characteristics of the proposed antenna are closely related to the parasitic elements. The proposed antenna has been fabricated for experimental measurement. The reflection coefficient, radiation pattern, radiation efficiency, and gain have been studied in detail. The simulated and measured impedance bandwidth is 27.0% (3.30–4.33 GHz), the maximum realized peak gain reaches up to 6.52 dBi at the frequency of 3.65 GHz. The radiation pattern has a single peak which is perpendicular to the surface of the substrate. The proposed antenna is suitable to be applied in the 5G mobile or WiMAX wireless communication. Dual antenna with a pair of parasitic elements has been investigated numerically to explain the principle of the proposed antenna.

Low-profile U-shaped DRA for ultra-wideband applications

2016 ◽  
Vol 9 (3) ◽  
pp. 621-627 ◽  
Author(s):  
Idris Messaoudene ◽  
Tayeb A. Denidni ◽  
Abdelmadjid Benghalia
Keyword(s):  
Dielectric Resonator ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
Wide Bandwidth ◽  
Operating Band ◽  
Low Profile ◽  
Measurement Results

In this paper, a microstrip-fed U-shaped dielectric resonator antenna (DRA) is simulated, designed, and fabricated. This antenna, in its simple configuration, operates from 5.45 to 10.8 GHz. To enhance its impedance bandwidth, the ground plane is first modified, which leads to an extended bandwidth from 4 to 10.8 GHz. Then by inserting a rectangular metallic patch inside the U-shaped DRA, the bandwidth is increased more to achieve an operating band from 2.65 to 10.9 GHz. To validate these results, an experimental antenna prototype is fabricated and measured. The obtained measurement results show that the proposed antenna can provide an ultra-wide bandwidth and a symmetric bidirectional radiation patterns. With these features, the proposed antenna is suitable for ultra-wideband applications.

scholarly journals Trapezoid Shape Patch Antenna for WLAN Application

2019 ◽  
Vol 8 (9S) ◽  
pp. 512-516
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Ground Plane ◽  
Local Area ◽  
Design Parameters ◽  
Impedance Bandwidth ◽  
Area Network ◽  
S Parameter

In this paper,CPW fed Trapezoid shape patch antenna is analyzed and investigated for Wireless Local Area Network (WLAN) application. The proposed antenna is fabricated on FR4 substrate having dimensions of 19mm ×21.2mm ×1.6mm. It resonates at 5.44 GHz frequency with peak return loss of 25.8 dB. The parametric study of proposed antenna is carried out to understand the effect of different values of ground plane on the impedance bandwidth, return loss of the antenna andalso to optimize the antenna parameters. The CPW-fed is used to enhance the bandwidth and to reduce the return loss of the antenna. The importance of different design parameters like current distribution, S-parameter, gain, and radiation pattern are studied. The results of the proposed antenna are useful for WLAN Application.

scholarly journals Beamwidth-Enhanced Low-Profile Dual-Band Circular Polarized Patch Antenna for CNSS Applications

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Hongmei Liu ◽  
Chenhui Xun ◽  
Shaojun Fang ◽  
Zhongbao Wang
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Axial Ratio ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Coupled Line ◽  
Low Profile ◽  
Feed Network ◽  
Single Input ◽  
Half Power

A low-profile dual-band circular polarized (CP) patch antenna with wide half-power beamwidths (HPBWs) is presented for CNSS applications. Simple stacked circular patches are used to achieve dual-band radiation. To enhance the HPBW for the two operation bands, a dual annular parasitic metal strip (D-APMS) combined with reduced ground plane (R-GP) is presented. A single-input feed network based on the coupled line transdirectional (CL-TRD) coupler is also proposed to provide two orthogonal modes at the two frequency bands simultaneously. Experimental results show that the 10 dB impedance bandwidth is 32.7%. The 3 dB axial ratio (AR) bandwidths for the lower and upper bands are 4.1% and 6.5%, respectively. At 1.207 GHz, the antenna has the HPBW of 123° and 103° in the xoz and yoz planes, separately. And the values are 127° and 113° at 1.561 GHz.

scholarly journals Millimeter Wave Fabry-Perot Resonator Antenna Fed by CPW with High Gain and Broadband

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Xue-Xia Yang ◽  
Guan-Nan Tan ◽  
Bing Han ◽  
Hai-Gao Xue
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Dielectric Substrate ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Broad Bandwidth ◽  
Low Profile ◽  
Fabry Perot

A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth ofS11less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

Sign in / Sign up

Export Citation Format

Share Document