scholarly journals High-Order Wave-Damage Interaction Coefficients (WDIC) Extracted through Modal Decomposition

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2749
Author(s):  
Hanfei Mei ◽  
Victor Giurgiutiu
Keyword(s):  
Mode Conversion ◽  
Wave Interaction ◽  
Element Model ◽  
Equation System ◽  
Wave Mode ◽  
Guided Wave ◽  
High Order ◽  
Interaction Coefficients ◽  
Modal Decomposition ◽  
A New Technique

This paper presents a new technique for the extraction of high-order wave-damage interaction coefficients (WDIC) through modal decomposition. The frequency and direction dependent complex-valued WDIC are used to model the scattering and mode conversion phenomena of guided wave interaction with damage. These coefficients are extracted from the harmonic analysis of local finite element model (FEM) mesh with non-reflective boundaries (NRB) and they are capable of describing the amplitude and phase of the scattered waves as a function of frequency and direction. To extract the WDIC of each wave mode, all the possible propagating wave modes are considered to be scattered simultaneously from the damage and propagate independently. Formulated in frequency domain, the proposed method is highly efficient, providing an overdetermined equation system for the calculation of mode participation factors, i.e., WDIC of each mode. Case studies in a 6-mm aluminum plate were carried out to validate the WDIC of: (1) a through-thickness hole and (2) a sub-surface crack. At higher frequency, scattered waves of high-order modes will appear and their WDIC can be successfully extracted through the modal decomposition.

scholarly journals Development of Ultrasonic Guided Wave Transducer for Monitoring of High Temperature Pipelines

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5443 ◽  
Author(s):  
Anurag Dhutti ◽  
Saiful Asmin Tumin ◽  
Wamadeva Balachandran ◽  
Jamil Kanfoud ◽  
Tat-Hean Gan
Keyword(s):  
High Temperature ◽  
Guided Waves ◽  
Elevated Temperatures ◽  
Element Model ◽  
Wave Mode ◽  
Guided Wave ◽  
Electromechanical Impedance ◽  
Active Sensor ◽  
Ultrasonic Guided Wave ◽  
Modes Of Vibration

High-temperature (HT) ultrasonic transducers are of increasing interest for structural health monitoring (SHM) of structures operating in harsh environments. This article focuses on the development of an HT piezoelectric wafer active sensor (HT-PWAS) for SHM of HT pipelines using ultrasonic guided waves. The PWAS was fabricated using Y-cut gallium phosphate (GaPO4) to produce a torsional guided wave mode on pipes operating at temperatures up to 600 °C. A number of confidence-building tests on the PWAS were carried out. HT electromechanical impedance (EMI) spectroscopy was performed to characterise piezoelectric properties at elevated temperatures and over long periods of time (>1000 h). Laser Doppler vibrometry (LDV) was used to verify the modes of vibration. A finite element model of GaPO4 PWAS was developed to model the electromechanical behaviour of the PWAS and the effect of increasing temperatures, and it was validated using EMI and LDV experimental data. This study demonstrates the application of GaPO4 for guided-wave SHM of pipelines and presents a model that can be used to evaluate different transducer designs for HT applications.

A Study on the Behavior of Ultrasonic Guided Wave Mode in a Pipe Using a Comb Transducer

2005 ◽  
Vol 297-300 ◽  
pp. 2182-2186
Author(s):  
Ik Keun Park ◽  
Yong Kwon Kim ◽  
Youn Ho Cho ◽  
Won Joon Song ◽  
Yeon Shik Ahn ◽  
...  
Keyword(s):  
Frequency Analysis ◽  
Mode Conversion ◽  
Group Velocity Dispersion ◽  
Longitudinal Mode ◽  
Wave Mode ◽  
Guided Wave ◽  
Flexural Mode ◽  
Time Frequency Analysis ◽  
Time Frequency ◽  
Ultrasonic Guided Wave

A preliminary study of the behavior of ultrasonic guided wave mode in a pipe using a comb transducer for maintenance inspection of power plant facilities has been verified experimentally. Guided wave mode identification is carried out in a pipe using time-frequency analysis methods such as wavelet transform (WT) and short time Fourier transform (STFT), compared with theoretically calculated group velocity dispersion curves for longitudinal and flexural mode. The results are in good agreement with analytical predictions and show the effectiveness of using the time-frequency analysis method to identify the individual guided wave modes. And, It was found out that longitudinal mode (0, 1) is affected by mode conversion less than the other modes. Therefore, L (0, 1) is selected as a optimal mode for evaluating location of the surface defect in a pipe.

A Wall Thinning Detection and Quantification Based on Guided Wave Mode Conversion Features

2006 ◽  
Vol 321-323 ◽  
pp. 795-798 ◽  
Author(s):  
Youn Ho Cho ◽  
Won Deok Oh ◽  
Joon Hyun Lee
Keyword(s):  
Long Range ◽  
Guided Waves ◽  
Velocity Dispersion ◽  
Mode Conversion ◽  
Group Velocity Dispersion ◽  
Wave Mode ◽  
Guided Wave ◽  
Wall Thinning ◽  
Theoretical Analyses ◽  
Data Calibration

This study presents a feasibility of using guided waves for a long-range inspection of pipe through investigation of mode conversion and scattering pattern from edge and wall-thinning in a steel pipe. Phase and group velocity dispersion curves for reference modes of pipes are illustrated for theoretical analyses. Predicted modes could be successfully generated by controlling frequency, receiver angle and wavelength. The dispersive characteristics of the modes from and edge wall-thinning are compared and analyzed respectively. The mode conversion characteristics are distinct depending on dispersive pattern of modes. Experimental feasibility study on the guided waves was carried out to explore wall thinning part in pipe for data calibration of a long range pipe monitoring by comb transducer and laser.

Analysis of S0/A0 guided wave mode conversion phenomenon

2018 ◽  
Author(s):  
Tomasz Wandowski ◽  
Pawel Malinowski ◽  
Pawel Kudela ◽  
Wieslaw Ostachowicz
Keyword(s):  
Mode Conversion ◽  
Wave Mode ◽  
Guided Wave

NUMERICAL MODELING OF WALL THINNING DEFECTS CHARACTERIZATION: APPLICATIONS IN LAMB WAVE GENERATION AND INTERACTION

2008 ◽  
Vol 22 (11) ◽  
pp. 935-940
Author(s):  
HYUNJO JEONG ◽  
SEUNG-SEOK LEE ◽  
YOUNG-GIL KIM
Keyword(s):  
Guided Waves ◽  
Lamb Waves ◽  
Mode Conversion ◽  
Wave Interaction ◽  
Guided Wave ◽  
Destructive Interference ◽  
Wall Thinning ◽  
Mode Dispersion ◽  
Periodic Ring ◽  
Axisymmetric Scattering

The generation of axisymmetric Lamb waves and interaction with wall thinning (corrosion) defects in hollow cylinders are simulated using the finite element method. Guided wave interaction with defects in cylinders is challenged by the multi-mode dispersion and the mode conversion. In this paper, two longitudinal, axisymmetric modes are generated using the concept of a time-delay periodic ring arrays (TDPRA), which makes use of the constructive/destructive interference concept to achieve the unidirectional emission and reception of guided waves. The axisymmetric scattering by the wall thinning extending in full circumference of a cylinder is studied with a two-dimensional FE simulation. The effect of wall thinning depth, axial extension, and the edge shape on the reflections of guided waves is discussed.

scholarly journals Improved Defect Detection Using Adaptive Leaky NLMS Filter in Guided-Wave Testing of Pipelines

2019 ◽  
Vol 9 (2) ◽  
pp. 294 ◽  
Author(s):  
Houman Nakhli Mahal ◽  
Kai Yang ◽  
Asoke Nandi
Keyword(s):  
Signal To Noise Ratio ◽  
Single Point ◽  
Element Model ◽  
Wave Mode ◽  
Guided Wave ◽  
Least Mean Square ◽  
Material Loss ◽  
Optimum Frequency ◽  
Cross Sectional ◽  
Axisymmetric Wave

Ultrasonic guided wave (UGW) testing of pipelines allows long range assessments of pipe integrity from a single point of inspection. This technology uses a number of arrays of transducers, linearly placed apart from each other to generate a single axisymmetric wave mode. The general propagation routine of the device results in a single time domain signal, which is then used by the inspectors to detect the axisymmetric wave for any defect location. Nonetheless, due to inherited characteristics of the UGW and non-ideal testing conditions, non-axisymmetric (flexural) waves will be transmitted and received in the tests. This adds to the complexity of results’ interpretation. In this paper, we implement an adaptive leaky normalized least mean square (NLMS) filter for reducing the effect of non-axisymmetric waves and enhancement of axisymmetric waves. In this approach, no modification in the device hardware is required. This method is validated using the synthesized signal generated by a finite element model (FEM) and real test data gathered from laboratory trials. In laboratory trials, six different sizes of defects with cross-sectional area (CSA) material loss of 8% to 3% (steps of 1%) were tested. To find the optimum frequency, several excitation frequencies in the region of 30–50 kHz (steps of 2 kHz) were used. Furthermore, two sets of parameters were used for the adaptive filter wherein the first set of tests the optimum parameters were set to the FEM test case and, in the second set of tests, the data from the pipe with 4% CSA defect was used. The results demonstrated the capability of this algorithm for enhancing a defect’s signal-to-noise ratio (SNR).

Reflection and Mode Conversion of Fundamental Torsional Guided Wave Mode From Lack of Bonding in Induction Pressure Welding

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Deepesh Vimalan ◽  
Krishnan Balasubramaniam ◽  
Prabhu Rajagopal
Keyword(s):  
Mode Conversion ◽  
Three Dimensional ◽  
Wave Mode ◽  
Bond Line ◽  
Fe Analysis ◽  
Guided Wave ◽  
Pressure Welding ◽  
Cross Sectional ◽  
3D Finite Element ◽  
Guided Mode

Interaction of fundamental torsional ultrasonic pipe guided mode T(0, 1) from defects caused by induction pressure welding (IPW) process is studied using three-dimensional (3D) finite element (FE) analysis validated by experiments. Defects are assumed as cross-sectional notches along the weld bond-line, and both surface-breaking and embedded features are considered. Results show that T(0, 1) mode reflection from weld defects is strongly influenced by features of the weld itself. However, with supplementary results such as the mode-converted flexural F(1, 3) and F(1, 2) modes and circumferential variation of T(0, 1) reflection, there is potential for an effective screening solution.

Sign in / Sign up

Export Citation Format

Share Document