scholarly journals A New Measurement Method for High Voltages Applied to an Ion Trap Generated by an RF Resonator

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1143
Author(s):  
Yunjae Park ◽  
Changhyun Jung ◽  
Myeongseok Seong ◽  
Minjae Lee ◽  
Dongil Dan Cho ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Measurement Method ◽  
Ion Trap ◽  
Functional Relation ◽  
Voltage Divider ◽  
Ion Traps ◽  
Absolute Amplitude ◽  
Simulation Results ◽  
Rf Shielding ◽  
Fitting Parameters

A new method is proposed to measure unknown amplitudes of radio frequency (RF) voltages applied to ion traps, using a pre-calibrated voltage divider with RF shielding. In contrast to previous approaches that estimate the applied voltage by comparing the measured secular frequencies with a numerical simulation, we propose using a pre-calibrated voltage divider to determine the absolute amplitude of large RF voltages amplified by a helical resonator. The proposed method does not require measurement of secular frequencies and completely removes uncertainty caused by limitations of numerical simulations. To experimentally demonstrate our method, we first obtained a functional relation between measured secular frequencies and large amplitudes of RF voltages using the calibrated voltage divider. A comparison of measured relations and simulation results without any fitting parameters confirmed the validity of the proposed method. Our method can be applied to most ion trap experiments. In particular, it will be an essential tool for surface ion traps which are extremely vulnerable to unknown large RF voltages and for improving the accuracy of numerical simulations for ion trap experiments.

Numerical analysis of trajectories in a Cassinian ion trap of second order with trap door ion inlet

2021 ◽  
Vol 27 (1) ◽  
pp. 3-12
Author(s):  
Bjoern Raupers ◽  
Hana Medhat ◽  
Juergen Grotemeyer ◽  
Frank Gunzer
Keyword(s):  
Ion Trap ◽  
Ion Traps ◽  
Second Order ◽  
Resolving Power ◽  
Periodic Pattern ◽  
Ion Motion ◽  
Trap Door ◽  
Mass Resolving Power ◽  
Long Time ◽  
The Fourier Transform

Ion traps like the Orbitrap are well known mass analyzers with very high resolving power. This resolving power is achieved with help of ions orbiting around an inner electrode for long time, in general up to a few seconds, since the mass signal is obtained by calculating the Fourier Transform of the induced signal caused by the ion motion. A similar principle is applied in the Cassinian Ion Trap of second order, where the ions move in a periodic pattern in-between two inner electrodes. The Cassinian ion trap has the potential to offer mass resolving power comparable to the Orbitrap with advantages regarding the experimental implementation. In this paper we have investigated the details of the ion motion analyzing experimental data and the results of different numerical methods, with focus on increasing the resolving power by increasing the oscillation frequency for ions in a high field ion trap. In this context the influence of the trap door, a tunnel through which the ions are injected into the trap, on the ion velocity becomes especially important.

Modulation instability in nonlinear chiral fiber

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Demissie Jobir Gelmecha ◽  
Ram Sewak Singh
Keyword(s):  
Theoretical Model ◽  
Numerical Simulations ◽  
Pulse Propagation ◽  
Modulation Instability ◽  
Constitutive Relations ◽  
Gain Spectrum ◽  
Circularly Polarized ◽  
Left Handed ◽  
Simulation Results ◽  
The Difference

AbstractIn this paper, the rigorous derivations of generalized coupled chiral nonlinear Schrödinger equations (CCNLSEs) and their modulation instability analysis have been explored theoretically and computationally. With the consideration of Maxwell’s equations and Post’s constitutive relations, a generalized CCNLSE has been derived, which describes the evolution of left-handed circularly polarized (LCP) and right-handed circularly polarized (RCP) components propagating through single-core nonlinear chiral fiber. The analysis of modulation instability in nonlinear chiral fiber has been investigated starting from CCNLSEs. Based on a theoretical model and numerical simulations, the difference on the modulation instability gain spectrum in LCP and RCP components through chiral fiber has been analyzed by considering loss and chirality into account. The obtained simulation results have shown that the loss distorts the sidebands of the modulation instability gain spectrum, while chirality modulates the gain for LCP and RCP components in a different manner. This suggests that adjusting chirality strength may control the loss, and nonlinearity simultaneously provides stable modulated pulse propagation.

scholarly journals A modular framework to generate robust biped locomotion: from planning to control

2021 ◽  
Vol 3 (9) ◽  
Author(s):  
Mohammadreza Kasaei ◽  
Ali Ahmadi ◽  
Nuno Lau ◽  
Artur Pereira
Keyword(s):  
Numerical Simulations ◽  
Predictive Control ◽  
Biped Locomotion ◽  
Input Output ◽  
Dynamics Model ◽  
Biped Robots ◽  
The Core ◽  
Simulation Results ◽  
Reference Trajectories ◽  
Modular Framework

AbstractBiped robots are inherently unstable because of their complex kinematics as well as dynamics. Despite many research efforts in developing biped locomotion, the performance of biped locomotion is still far from the expectations. This paper proposes a model-based framework to generate stable biped locomotion. The core of this framework is an abstract dynamics model which is composed of three masses to consider the dynamics of stance leg, torso, and swing leg for minimizing the tracking problems. According to this dynamics model, we propose a modular walking reference trajectories planner which takes into account obstacles to plan all the references. Moreover, this dynamics model is used to formulate the controller as a Model Predictive Control (MPC) scheme which can consider some constraints in the states of the system, inputs, outputs, and also mixed input-output. The performance and the robustness of the proposed framework are validated by performing several numerical simulations using MATLAB. Moreover, the framework is deployed on a simulated torque-controlled humanoid to verify its performance and robustness. The simulation results show that the proposed framework is capable of generating biped locomotion robustly.

scholarly journals Spatiotemporal Patterns Formed by a Discrete Nutrient-Phytoplankton Model with Time Delay

Complexity ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Feifan Zhang ◽  
Wenjiao Zhou ◽  
Lei Yao ◽  
Xuanwen Wu ◽  
Huayong Zhang
Keyword(s):  
Steady State ◽  
Time Delay ◽  
Numerical Simulations ◽  
Functional Response ◽  
Bifurcation Analysis ◽  
Discrete Model ◽  
Continuous Model ◽  
Spatiotemporal Patterns ◽  
Homogeneous Steady State ◽  
Simulation Results

In this research, a continuous nutrient-phytoplankton model with time delay and Michaelis–Menten functional response is discretized to a spatiotemporal discrete model. Around the homogeneous steady state of the discrete model, Neimark–Sacker bifurcation and Turing bifurcation analysis are investigated. Based on the bifurcation analysis, numerical simulations are carried out on the formation of spatiotemporal patterns. Simulation results show that the diffusion of phytoplankton and nutrients can induce the formation of Turing-like patterns, while time delay can also induce the formation of cloud-like pattern by Neimark–Sacker bifurcation. Compared with the results generated by the continuous model, more types of patterns are obtained and are compared with real observed patterns.

The penetration and ricochet of ogive-nosed rigid projectiles obliquely impacting metallic targets

2021 ◽  
pp. 204141962110377
Author(s):  
Yaniv Vayig ◽  
Zvi Rosenberg
Keyword(s):  
Experimental Data ◽  
Numerical Simulations ◽  
Dynamic Pressure ◽  
Oblique Impacts ◽  
Simulation Results ◽  
The Impact ◽  
Penetration Depths ◽  
Resistance To Penetration ◽  
Good Agreement

A large number of 3D numerical simulations were performed in order to follow the trajectory changes of rigid CRH3 ogive-nosed projectiles, impacting semi-infinite metallic targets at various obliquities. These trajectory changes are shown to be related to the threshold ricochet angles of the projectile/target pairs. These threshold angles are the impact obliquities where the projectiles end up moving in a path parallel to the target’s face. They were found to depend on a non-dimensional entity which is equal to the ratio between the target’s resistance to penetration and the dynamic pressure exerted by the projectile upon impact. Good agreement was obtained by comparing simulation results for these trajectory changes with experimental data from several published works. In addition, numerically-based relations were derived for the penetration depths of these ogive-nosed projectiles at oblique impacts, which are shown to agree with the simulation results.

Numerical Modeling of Multi-Frequency Complex Dielectric Permittivity Dispersion of Sedimentary Rocks

Geophysics ◽  
2021 ◽  
pp. 1-69
Author(s):  
Artur Posenato Garcia ◽  
Zoya Heidari
Keyword(s):  
Numerical Simulation ◽  
Dielectric Permittivity ◽  
Numerical Simulations ◽  
Dielectric Response ◽  
Water Saturation ◽  
Pore Scale ◽  
Simulation Results ◽  
Wet Rocks ◽  
Permittivity Measurements ◽  
The Impact

The dielectric response of rocks results from electric double layer (EDL), Maxwell-Wagner (MW), and dipolar polarizations. The EDL polarization is a function of solid-fluid interfaces, pore water, and pore geometry. MW and dipolar polarizations are functions of charge accumulation at the interface between materials with contrasting impedances and the volumetric concentration of its constituents, respectively. However, conventional interpretation of dielectric measurements only accounts for volumetric concentrations of rock components and their permittivities, not interfacial properties such as wettability. Numerical simulations of dielectric response of rocks provides an ideal framework to quantify the impact of wettability and water saturation ( Sw) on electric polarization mechanisms. Therefore, in this paper we introduce a numerical simulation method to compute pore-scale dielectric dispersion effects in the interval from 100 Hz to 1 GHz including impacts of pore structure, Sw, and wettability on permittivity measurements. We solve the quasi-electrostatic Maxwell's equations in three-dimensional (3D) pore-scale rock images in the frequency domain using the finite volume method. Then, we verify simulation results for a spherical material by comparing with the corresponding analytical solution. Additionally, we introduce a technique to incorporate α-polarization to the simulation and we verify it by comparing pore-scale simulation results to experimental measurements on a Berea sandstone sample. Finally, we quantify the impact of Sw and wettability on broadband dielectric permittivity measurements through pore-scale numerical simulations. The numerical simulation results show that mixed-wet rocks are more sensitive than water-wet rocks to changes in Sw at sub-MHz frequencies. Furthermore, permittivity and conductivity of mixed-wet rocks have weaker and stronger dispersive behaviors, respectively, when compared to water-wet rocks. Finally, numerical simulations indicate that conductivity of mixed-wet rocks can vary by three orders of magnitude from 100 Hz to 1 GHz. Therefore, Archie’s equation calibrated at the wrong frequency could lead to water saturation errors of 73%.

scholarly journals Numerical Simulations of V-Shaped Plates Subjected to Blast Loadings: A Validation Study

2016 ◽  
Vol 10 (11) ◽  
pp. 203
Author(s):  
Mohd Zaid Othman ◽  
Qasim H. Shah ◽  
Muhammad Akram Muhammad Khan ◽  
Tan Kean Sheng ◽  
M. A. Yahaya ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Variable Mass ◽  
Blast Loading ◽  
Experimental Results ◽  
Average Difference ◽  
Simulation Results ◽  
Blast Loadings ◽  
Carrier Vehicle ◽  
Good Agreement

A series of numerical simulations utilizing LS-DYNA was performed to determine the mid-point deformations of V-shaped plates due to blast loading. The numerical simulation results were then compared with experimental results from published literature. The V-shaped plate is made of DOMEX 700 and is used underneath an armour personal carrier vehicle as an anti-tank mine to mitigate the effects of explosion from landmines in a battlefield. The performed numerical simulations of blast loading of V-shaped plates consisted of various angles i.e. 60°, 90°, 120°, 150° and 180°; variable mass of explosives located at the central mid-point of the V-shaped vertex with various stand-off distances. It could be seen that the numerical simulations produced good agreement with the experimental results where the average difference was about 26.6%.

scholarly journals Discussion on the Theoretical Basis for Cross-Over Method Applied to Downhole Wave Velocity Test

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Qing Dong ◽  
Zheng-hua Zhou ◽  
Su Jie ◽  
Bing Hao ◽  
Yuan-dong Li
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Wave Velocity ◽  
Theoretical Basis ◽  
Influence Factors ◽  
P Wave ◽  
Engineering Practice ◽  
S Wave ◽  
Simulation Results ◽  
The Cross

At engineering practice, the theoretical basis for the cross-over method, used to obtain shear wave arrival time in the downhole method of the wave velocity test by surface forward and backward strike, is that the polarity of P-wave keeps the same, while the polarity of S-wave transforms when the direction of strike inverted. However, the characteristics of signals recorded in tests are often found to conflict with this theoretical basis for the cross-over method, namely, the polarity of the P-wave also transforms under the action of surface forward and backward strike. Therefore, 3D finite element numerical simulations were conducted to study the validity of the theoretical basis for the cross-over method. The results show that both shear and compression waves are observed to be in 180° phase difference between horizontal signal traces, consistent with the direction of excitation generated by reversed impulse. Furthermore, numerical simulation results prove to be reliable by the analytic solution; it shows that the theoretical basis for the cross-over method applied to the downhole wave velocity test is improper. In meanwhile, numerical simulations reveal the factors (inclining excitation, geophone deflection, inclination, and background noise) that may cause the polarity of the P-wave not to reverse under surface forward and backward strike. Then, as to reduce the influence factors, we propose a method for the downhole wave velocity test under surface strike, the time difference of arrival is based between source peak and response peak, and numerical simulation results show that the S-wave velocity by this method is close to the theoretical S-wave velocity of soil.

scholarly journals Study the effect of angle of attack on flow characteristics at racing bike helmet using CFD

2018 ◽  
Vol 204 ◽  
pp. 06001
Author(s):  
Syamsuri ◽  
M Hasan Syafik ◽  
Yudho Putro Iswanto
Keyword(s):  
Numerical Simulations ◽  
Drag Coefficient ◽  
Aerodynamic Force ◽  
Angle Of Attack ◽  
Flow Characteristics ◽  
Reynold Number ◽  
Attack Angle ◽  
Large Area ◽  
Drag Racing ◽  
Simulation Results

At a cyclist drag racing champions greatly affect the speed of the bike, especially on the use of racing bike helmets. If the aerodynamic force from the racing bike helmet is getting smaller than the use of helmets on the bike racing will be more optimal and will affect the rate of the racer. In this study, numerical simulations were used to investigate the magnitude of the drag force that occurs around the surface of the helmet. With CFD software, 4 variations of attack angle 0°, 10°, 20° and 30° and variations of Reynold number 7.14x104, 1.00x105, and 1.16x105 are simulated to determine the flow characteristics of each state. The simulation results show that large area vortex is formed at the bottom of the helmet curve and dominates at the attack angle 30°. The result of the drag coefficient generated at the angle of attack 0° to 20° tends to decrease but at the attack angle 200 and 30° the drag coefficient increases.

Sign in / Sign up

Export Citation Format

Share Document