scholarly journals Piezoelectric Energy Harvesting from Suspension Structures with Piezoelectric Layers

Sensors ◽  
2020 ◽  
Vol 20 (13) ◽  
pp. 3755 ◽  
Author(s):  
Min Wang ◽  
Yiming Xia ◽  
Huayan Pu ◽  
Yi Sun ◽  
Jiheng Ding ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Impedance Matching ◽  
Low Frequency ◽  
Single Layer ◽  
Leaf Spring ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Low Frequency Vibration ◽  
Piezoelectric Layers ◽  
Series Of Experiments

In this paper, we propose a generator for piezoelectric energy harvesting from suspension structures. This device consists of a leaf spring and eight pairs of piezoelectric layers attached to inner and outer surfaces. We present a special type of leaf spring, which can magnify the force from the workload to allow the piezoelectric layers to achieve larger deformation. The generator is to solve the problem of vibration energy reutilization in a low-frequency vibration system. To verify the efficiency of the proposed configuration, a series of experiments are operated. The results indicate that the resonance frequency (25.2 Hz) obtained from the sweep experiment is close to the simulation result (26.1 Hz). Impedance-matching experiments show that the sum of the output power attains 1.7 mW, and the maximum single layer reaches 0.6 mW with an impedance matching of 610 KΩ, and the instantaneous peak-peak power density is 3.82 mW/cm3. The capacitor-charging performance of the generator is also excellent under the series condition. For a 4.7 μF capacitor, the voltage is charged to 25 V in 30 s and limited at 32 V in 80 s. These results demonstrate the exploitable potential of piezoelectric energy harvesting from suspension structures.

scholarly journals Piezoelectric Energy Harvesting with an Ultrasonic Vibration Source

Actuators ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 8
Author(s):  
Tao Li ◽  
Pooi Lee
Keyword(s):  
Energy Harvesting ◽  
High Power ◽  
High Frequency ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Low Frequency ◽  
Vibration Source ◽  
Piezoelectric Energy ◽  
Power Ultrasonic ◽  
Ultrasonic Cutting

A piezoelectric energy harvester was developed in this paper. It is actuated by the vibration leakage from the nodal position of a high-power ultrasonic cutting transducer. The harvester was excited at a low displacement amplitude (0.73 µmpp). However, its operation frequency is quite high and reaches the ultrasonic range (24.4 kHz). Compared with another low frequency harvester (66 Hz), both theoretical and experimental results proved that the advantages of this high frequency harvester include (i) high current generation capability (up to 20 mApp compared to 1.3 mApp of the 66 Hz transducer) and (ii) low impedance matching resistance (500 Ω in contrast to 50 kΩ of the 66 Hz transducer). This energy harvester can be applied either in sensing, or vibration controlling, or simply energy harvesting in a high-power ultrasonic system.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

A design method for low-frequency rotational piezoelectric energy harvesting in micro applications

2019 ◽  
Vol 26 (3) ◽  
pp. 981-991
Author(s):  
Xiaobo Rui ◽  
Zhoumo Zeng ◽  
Yu Zhang ◽  
Yibo Li ◽  
Hao Feng ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Design Method ◽  
Low Frequency ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy

scholarly journals Study of a Low-Power-Consumption Piezoelectric Energy Harvesting Circuit Based on Synchronized Switching Technology

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3166
Author(s):  
Jianfeng Hong ◽  
Fu Chen ◽  
Ming He ◽  
Sheng Wang ◽  
Wenxiang Chen ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Theoretical Analysis ◽  
Power Consumption ◽  
Low Power ◽  
Impedance Matching ◽  
Maximum Energy ◽  
Low Power Consumption ◽  
Piezoelectric Energy Harvesting ◽  
Interface Circuit ◽  
Piezoelectric Energy

This paper presents a study of a piezoelectric energy harvesting circuit based on low-power-consumption synchronized switch technology. The proposed circuit includes a parallel synchronized switch harvesting on inductor interface circuit (P-SSHI) and a step-down DC-DC converter. The synchronized switch technology is applied to increase the conversion efficiency of the circuit. The DC-DC converter is used to accomplish the impedance matching for different loads. A low-power-consumption microcontroller and discrete components are used to build the P-SSHI interface circuit. The study starts with theoretical analysis and simulations of the P-SSHI interface circuit. Simulations and experiments were conducted to validate the theoretical analysis. The experimental results show that the maximum energy harvested by the system with a P-SSHI interface circuit is 231 μW, which is 2.89 times that of a system without the P-SSHI scheme. The power consumption of the P-SSHI interface circuit can be as low as 10.6 μW.

scholarly journals A Review on Piezoelectric Energy Harvesting: Materials, Methods, and Circuits

2019 ◽  
Vol 4 (1) ◽  
pp. 3-39 ◽  
Author(s):  
Shashank Priya ◽  
Hyun-Cheol Song ◽  
Yuan Zhou ◽  
Ronnie Varghese ◽  
Anuj Chopra ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Power Management ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Small Scale ◽  
Piezoelectric Energy Harvesting ◽  
Wide Bandwidth ◽  
Piezoelectric Energy ◽  
Continuous Power

Abstract Piezoelectric microelectromechanical systems (PiezoMEMS) are attractive for developing next generation self-powered microsystems. PiezoMEMS promises to eliminate the costly assembly for microsensors/microsystems and provide various mechanisms for recharging the batteries, thereby, moving us closer towards batteryless wireless sensors systems and networks. In order to achieve practical implementation of this technology, a fully assembled energy harvester on the order of a quarter size dollar coin (diameter=24.26 mm, thickness=1.75 mm) should be able to generate about 100 μW continuous power from low frequency ambient vibrations (below 100 Hz). This paper reviews the state-of-the-art in microscale piezoelectric energy harvesting, summarizing key metrics such as power density and bandwidth of reported structures at low frequency input. This paper also describes the recent advancements in piezoelectric materials and resonator structures. Epitaxial growth and grain texturing of piezoelectric materials is being developed to achieve much higher energy conversion efficiency. For embedded medical systems, lead-free piezoelectric thin films are being developed and MEMS processes for these new classes of materials are being investigated. Non-linear resonating beams for wide bandwidth resonance are also reviewed as they would enable wide bandwidth and low frequency operation of energy harvesters. Particle/granule spray deposition techniques such as aerosol-deposition (AD) and granule spray in vacuum (GSV) are being matured to realize the meso-scale structures in a rapid manner. Another important element of an energy harvester is a power management circuit, which should maximize the net energy harvested. Towards this objective, it is essential for the power management circuit of a small-scale energy harvester to dissipate minimal power, and thus it requires special circuit design techniques and a simple maximum power point tracking scheme. Overall, the progress made by the research and industrial community has brought the energy harvesting technology closer to the practical applications in near future.

scholarly journals Impedance matching for broadband piezoelectric energy harvesting

2013 ◽  
Vol 476 ◽  
pp. 012083 ◽  
Author(s):  
F Hagedorn ◽  
J Leicht ◽  
D Sanchez ◽  
T Hehn ◽  
Y Manoli
Keyword(s):  
Energy Harvesting ◽  
Impedance Matching ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy

Self-Start Piezoelectric Energy Harvesting Circuit With Adjustable UVLO Converter for Wireless Sensor Network

2017 ◽  
Author(s):  
Hyun Jun Jung ◽  
Soobum Lee ◽  
Hamid Jabbar ◽  
Se Yeong Jeong ◽  
Tae Hyun Sung
Keyword(s):  
Wireless Sensor Network ◽  
Energy Harvesting ◽  
Sensor Network ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Wireless Sensor ◽  
Experimental Result ◽  
Piezoelectric Energy Harvesting ◽  
Wireless Sensor Node ◽  
Piezoelectric Energy

This paper proposes a self-start piezoelectric energy harvesting circuit with an undervoltage-lockout (UVLO) converter for a wireless sensor network (WSN). First, a self-start circuit with mini piezoelectric energy harvester (PEH) is designed to supply the power for operation of the oscillator without battery. The experimental results show that a batteryless self-start circuit successfully operates the oscillator with mini-PEH, and self-starting time is 0.45 s. Second, this paper proposes an adjustable UVLO converter that can supply the power even if a power consumption of a wireless sensor node is higher than generated power from PEH. The experimental result shows the adjustable UVLO converter supplies 45 mW for 0.12 s after charging the output power of an impedance matching circuit (1.7 mW) for 10 s. This paper shows that the proposed circuit successfully overcomes challenging issues — self-start and lower power generation — for powering WSN.

Sign in / Sign up

Export Citation Format

Share Document