scholarly journals Model for Wireless Magnetoelastic Strain Sensors

Sensors ◽  
2020 ◽  
Vol 20 (12) ◽  
pp. 3557
Author(s):  
Eduardo S. Bastos ◽  
Cristina Bormio-Nunes ◽  
Thomas G. R. Clarke ◽  
Frank P. Missell
Keyword(s):  
Magnetic Field ◽  
Resonant Frequency ◽  
Strain Sensor ◽  
Strain Curve ◽  
Strain Sensors ◽  
Frequency Variation ◽  
Marine Riser ◽  
Magnetoelastic Properties ◽  
Materials Used ◽  
Strain Dependent

This paper describes a magnetoelastic strain sensor based on the ∆E effect and discusses some materials used in its construction. A polycrystalline Fe–Al–B alloy with good quality magnetoelastic properties was used as the transducer and glued to the test object, either brass plates or rods of SAE 1010 steel. The strain-dependent magnetic field of the transducer changes the operating point of the resonator, a strip of field-annealed Metglas 2826MB3, resulting in a modification of its resonant frequency. A model was developed to simulate the strain-dependent magnetic field acting on the resonator and thus to calculate curves of resonant frequency vs. deformation. With the help of this model, differences in the shape of the frequency vs. strain curve can be understood. For a sensor with resonant frequency of 60.5 kHz glued to a rod of SAE 1010 steel, a total resonant frequency variation ∆f ~7 kHz was observed for a deformation of 1100 ppm. The geometry of this sensor is especially favorable for the remote monitoring of a steel surface, such as the wires of the tensile armor of a marine riser.

scholarly journals Development of Highly Sensitive Strain Sensor Using Area-Arrayed Graphene Nanoribbons

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1701
Author(s):  
Ken Suzuki ◽  
Ryohei Nakagawa ◽  
Qinqiang Zhang ◽  
Hideo Miura
Keyword(s):  
Graphene Nanoribbons ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Sensitive Strain ◽  
Bending Test ◽  
Gauge Factor ◽  
Four Point Bending ◽  
Current Voltage ◽  
Highly Sensitive ◽  
Current Voltage Relationship

In this study, a basic design of area-arrayed graphene nanoribbon (GNR) strain sensors was proposed to realize the next generation of strain sensors. To fabricate the area-arrayed GNRs, a top-down approach was employed, in which GNRs were cut out from a large graphene sheet using an electron beam lithography technique. GNRs with widths of 400 nm, 300 nm, 200 nm, and 50 nm were fabricated, and their current-voltage characteristics were evaluated. The current values of GNRs with widths of 200 nm and above increased linearly with increasing applied voltage, indicating that these GNRs were metallic conductors and a good ohmic junction was formed between graphene and the electrode. There were two types of GNRs with a width of 50 nm, one with a linear current–voltage relationship and the other with a nonlinear one. We evaluated the strain sensitivity of the 50 nm GNR exhibiting metallic conduction by applying a four-point bending test, and found that the gauge factor of this GNR was about 50. Thus, GNRs with a width of about 50 nm can be used to realize a highly sensitive strain sensor.

scholarly journals Strain Sensor Based on Biological Nanomaterial

2021 ◽  
Vol 6 (1) ◽  
pp. 23
Author(s):  
Levan P. Ichkitidze ◽  
Alexander Yu. Gerasimenko ◽  
Dmitry V. Telyshev ◽  
Eugeny P. Kitsyuk ◽  
Vladimir A. Petukhov ◽  
...  
Keyword(s):  
Screen Printing ◽  
Respiratory Diseases ◽  
Specific Conductivity ◽  
Strain Sensor ◽  
Aqueous Dispersion ◽  
Strain Sensors ◽  
Bending Angle ◽  
Multi Walled Carbon Nanotubes ◽  
Number Of Cycles ◽  
Walled Carbon Nanotubes

We investigated a prototype of a strain sensor based on the layers of a bionanomaterial containing bovine serum albumin (BSA matrix) and multi-walled carbon nanotubes (MWCNT filler). The aqueous dispersion of 25 wt.% BSA/0.3 wt.% MWCNT was applied by screen printing onto flexible polyethylene terephthalate substrates. After drying the layers by laser irradiation (~970 nm), various parameters of the layers were controlled, i.e., resistance R, bending angle θ, number of cycles n, and measurement time. One measurement cycle corresponded to a change within the range θ = ±150°. The layers of the BSA/MWCNT bionanomaterial had dimensions of (15 ÷ 20) mm × (8 ÷ 10) mm × (0.5 ÷ 1. 5) µm. The dependences of resistance R on the bending angle θ were similar for all layers at θ = ±30, and the R(θ) curves represented approximate linear dependences (with an error of ≤ 10%); beyond this range, the dependences became nonlinear. The following quantitative values were obtained for the investigated strain sensor: specific conductivity ~1 ÷ 10 S/m, linear strain sensitivity ~160, and bending sensitivity 1.0 ÷ 1.5%/°. These results are high. The examined layers of the bionanomaterial BSA/MWCNT as a strain sensor are of particular interest for medical practice. In particular, strain sensors can be implemented by applying a water dispersion of nanomaterials to human skin using a 3D printer for monitoring movements (arms and blinking) and the detection of signs of pathology (dysphagia, respiratory diseases, angina, etc.).

scholarly journals A Novel Textile Stitch-Based Strain Sensor for Wearable End Users

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1469 ◽  
Author(s):  
Orathai Tangsirinaruenart ◽  
George Stylios
Keyword(s):  
Mechanical Properties ◽  
Electrical Resistance ◽  
Body Movement ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Heart Monitoring ◽  
Textile Sensors ◽  
Good Repeatability ◽  
The Ideal

This research presents an investigation of novel textile-based strain sensors and evaluates their performance. The electrical resistance and mechanical properties of seven different textile sensors were measured. The sensors are made up of a conductive thread, composed of silver plated nylon 117/17 2-ply, 33 tex and 234/34 4-ply, 92 tex and formed in different stitch structures (304, 406, 506, 605), and sewn directly onto a knit fabric substrate (4.44 tex/2 ply, with 2.22, 4.44 and 7.78 tex spandex and 7.78 tex/2 ply, with 2.22 and 4.44 tex spandex). Analysis of the effects of elongation with respect to resistance indicated the ideal configuration for electrical properties, especially electrical sensitivity and repeatability. The optimum linear working range of the sensor with minimal hysteresis was found, and the sensor’s gauge factor indicated that the sensitivity of the sensor varied significantly with repeating cycles. The electrical resistance of the various stitch structures changed significantly, while the amount of drift remained negligible. Stitch 304 2-ply was found to be the most suitable for strain movement. This sensor has a wide working range, well past 50%, and linearity (R2 is 0.984), low hysteresis (6.25% ΔR), good gauge factor (1.61), and baseline resistance (125 Ω), as well as good repeatability (drift in R2 is −0.0073). The stitch-based sensor developed in this research is expected to find applications in garments as wearables for physiological wellbeing monitoring such as body movement, heart monitoring, and limb articulation measurement.

scholarly journals Structural Reinforcement Effect of a Flexible Strain Sensor Integrated with Pneumatic Balloon Actuators for Soft Microrobot Fingers

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 395
Author(s):  
Satoshi Konishi ◽  
Fuminari Mori ◽  
Ayano Shimizu ◽  
Akiya Hirata
Keyword(s):  
Liquid Metal ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Original Performance ◽  
Sensors And Actuators ◽  
Parylene C ◽  
Structural Reinforcement ◽  
Effective Combination ◽  
Metal Strain ◽  
Flexible Strain Sensor

Motion capture of a robot and tactile sensing for a robot require sensors. Strain sensors are used to detect bending deformation of the robot finger and to sense the force from an object. It is important to introduce sensors in effective combination with actuators without affecting the original performance of the robot. We are interested in the improvement of flexible strain sensors integrated into soft microrobot fingers using a pneumatic balloon actuator (PBA). A strain sensor using a microchannel filled with liquid metal was developed for soft PBAs by considering the compatibility of sensors and actuators. Inflatable deformation generated by PBAs, however, was found to affect sensor characteristics. This paper presents structural reinforcement of a liquid metal-based sensor to solve this problem. Parylene C film was deposited into a microchannel to reinforce its structure against the inflatable deformation caused by a PBA. Parylene C deposition into a microchannel suppressed the interference of inflatable deformation. The proposed method enables the effective combination of soft PBAs and a flexible liquid metal strain sensor for use in microrobot fingers.

FREQUENCY VARIATION IN IONOSPHERIC CYCLOTRON HARMONIC SERIES OBTAINED BY THE ALOUETTE I SATELLITE

1966 ◽  
Vol 44 (5) ◽  
pp. 987-994 ◽  
Author(s):  
R. E. Barrington ◽  
Luise Herzberg
Keyword(s):  
Magnetic Field ◽  
Cyclotron Frequency ◽  
Harmonic Series ◽  
Frequency Variation ◽  
Theoretical Studies ◽  
Experimental Accuracy ◽  
Laboratory Results ◽  
Cyclotron Harmonics ◽  
Cyclotron Harmonic ◽  
Recent Laboratory

Ionograms produced by the Alouette I topside sounder frequently show well-developed series of cyclotron harmonics. Their frequencies have been determined from A (amplitude) scans with an accuracy of ~0.02 Mc/s for the sweep range of 1 to 6 Mc/s. In all cases examined, the frequencies of all of the members of the harmonic series are, within the experimental accuracy, integral multiples of the cyclotron frequency derived from the best present estimates of the earth's magnetic field strength at the satellite height. This result is discussed in the light of recent laboratory results and theoretical studies.

Research on the Performance of Strain Sensors Applied to Bridges

2014 ◽  
Vol 875-877 ◽  
pp. 680-684
Author(s):  
Zhi Liu ◽  
Jing Liu ◽  
Shu Ri Cai
Keyword(s):  
Health Monitoring ◽  
Performance Test ◽  
Strain Sensor ◽  
Safety Monitoring ◽  
Strain Sensors ◽  
Great Role ◽  
Temperature Drift ◽  
Short Life ◽  
Test Analysis ◽  
Health Monitoring System

Strengthening safety monitoring of bridges during service time and improving the capability of emergency support have become the priority of the development of China’s present transportation system. Strain sensors play a great role in bridge detection and health monitoring system. In order to overcome disadvantages of traditional resistance strain sensors, such as big temperature drift, short life and inadaptability in the environment of low temperature and humidity, new arch strain sensors have been developed. This paper mainly discusses the structural and material characteristics of this sensor, as well as the performance test analysis of this strain sensor.

Energy Resource for a RFID System Based on Dynamic Features of Reddy-Levinson Beam

2020 ◽  
Author(s):  
Alireza Babaei ◽  
Johné Parker ◽  
Paria Moshaver
Keyword(s):  
Resonant Frequency ◽  
Shear Deformation ◽  
Displacement Field ◽  
Energy Harvester ◽  
Frequency Variation ◽  
Low Input ◽  
Piezoelectric Energy ◽  
Rfid System ◽  
Proposed Model ◽  
Thick Beam

Abstract Understanding the effect of design parameters on resonant frequency variation is a critically important aspect of piezoelectric energy harvester device design. As a first step in more accurately investigating the performance of a fixture designed for targeted RFID tag communication that also utilizes an energy harvesting application, this paper analyzes the variations in resonant frequency of a higher-order beam based on Reddy-Levinson theory (RLBT) under rotation effects. A long-term goal of this research is to implement an effective energy harvester on the RFID system. Part of the experimental RFID test fixture can be modeled as a beam (or beam element); thus, understanding the resonance frequency variations due to shear deformation and rotation effects is an important first step in obtaining information about the efficacy of the fixture in serving as an energy harvester. Investigating the performance of a beam also provides valuable information about the maximum power, frequency bandwidth, and tuning ability of the device that can be expected from an analogous energy harvester. For the first time, the resonant frequency variation of a rotating thick beam is investigated. Specifically, RLBT is used to verify the effects of shear deformation upon resonant frequency, and a coupled displacement field is utilized to enable tuning the potential piezoelectric energy harvester to low-input excitations by means of constraining translational and rotational movements of the system based on a linear constraint equation. Navier’s method as an analytical-numerical method is adopted to discretize the continuous system and to find resonant frequencies, respectively. Results reveal the significance of beam thickness and rotation effects of the proposed model for the purpose of minimizing energy usage. Current results are compared and verified numerically with available benchmarks to confirm a satisfactory level of accuracy. The proposed model, which is based on a coupled displacement field, can also be used to design other piezoelectric electro-mechanical-systems; e.g., vibration isolators, and vibration controllers. In other words, in an energy-scavenging system, a fundamental understanding of parameters affecting the resonant frequency can be accomplished through the presented analysis. The proposed model highlights the fact that, by adopting a proper speed factor, tuning the piezoelectric energy harvester to low-input excitations is possible. Additionally, it is observed that the rotation effect on the resonant frequency is more severe than effects of slenderness ratio. Finally, in this paper an improved model is proposed to capture the shear deformation effect, particularly for thick-beam energy harvesters, with the capability of tuning to low-input excitations.

Area-Arrayed Graphene Nano-Ribbon-Base Strain Sensor

2018 ◽  
Author(s):  
Ryohei Nakagawa ◽  
Zhi Wang ◽  
Ken Suzuki
Keyword(s):  
Chemical Vapor Deposition ◽  
Stress Concentration ◽  
Health Monitoring ◽  
Vapor Deposition ◽  
Strain Sensor ◽  
Chemical Vapor ◽  
High Sensitivity ◽  
Strain Sensors ◽  
Chemical Vapor Deposition Method ◽  
High Quality

Health monitoring devices using a strain sensor, which shows high sensitivity and large deformability, are strongly demanded due to further aging of society with fewer children. Conventional strain sensors, such as metallic strain gauges and semiconductive strain sensors, however, aren’t applicable to health monitoring because of their low sensitivity and deformability. In this study, fundamental design of area-arrayed graphene nano-ribbon (GNR) strain senor was proposed in order to fabricate next-generation strain sensor. The sensor was consisted of two sections, which are stress concentration section and stress detecting section. This structure can take full advantage of GNR’s properties. Moreover, high quality GNR fabrication process, which is one of the important process in the sensor, was developed by applying CVD (Chemical Vapor Deposition) method. Top-down approach was applied to fabricate the GNR. At first, in order to synthesize a high-quality graphene sheet, acetylene-based LPCVD (low pressure chemical vapor deposition) using a closed Cu foil was employed. After that, graphene was transferred silicon substrate and the quality was evaluated. The high quality graphene was transferred on the soft PDMS substrate and metallic electrodes were fabricated by applying MEMS technology. Area-arrayed fine pin structure was fabricated by using hard PDMS as a stress-concentration section. Finally, both sections were integrated to form a highly sensitive and large deformable pressure sensor. The strain sensitivity of the GNR-base sensor was also evaluated.

scholarly journals A novel strain sensor using a microchannel embedded in PDMS

2018 ◽  
Vol 4 (2) ◽  
pp. 1 ◽  
Author(s):  
Angelica Campigotto ◽  
Stephane Leahy ◽  
Ayan Choudhury ◽  
Guowei Zhao ◽  
Yongjun Lai
Keyword(s):  
Finite Element ◽  
Rotation Angle ◽  
Strain Sensor ◽  
Element Model ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Sectional Area ◽  
Cross Sectional ◽  
Higher Sensitivity

A novel, inexpensive, and easy-to-use strain sensor using polydimethylsiloxane (PDMS)  was developed. The sensor consists of a microchannel that is partially filled with a coloured liquid and embedded in a piece of PDMS. A finite element model was developed to optimize the geometry of the microchannel to achieve higher sensitivity. The highest gauge factor that was measured experimentally was 41. The gauge factor was affected by the microchannel’s square cross-sectional area, the number of basic units in the microchannel, and the inlet and outlet configuration. As a case study, the developed strain sensors were used to measure the rotation angle of the wrist and finger joints.

scholarly journals Corrugated Photoactive Thin Films for Flexible Strain Sensor

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1970 ◽  
Author(s):  
Donghyeon Ryu ◽  
Alfred Mongare
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Electrical Properties ◽  
Tensile Strain ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Optical And Electrical Properties ◽  
Strain Sensing ◽  
Dc Voltage ◽  
Flexible Strain Sensor

In this study, a flexible strain sensor is devised using corrugated bilayer thin films consisting of poly(3-hexylthiophene) (P3HT) and poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS). In previous studies, the P3HT-based photoactive non-corrugated thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to brittle non-corrugated thin film constituents. To address this issue, it is aimed to design a mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to design the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS conductive thin film affects the optical and electrical properties. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and the DC voltage strain sensing capability of the flexible strain sensors was validated. As a result, the flexible strain sensor exhibited a tensile strain sensing range up to 5% at a frequency up to 15 Hz with a maximum gauge factor ~7.

Sign in / Sign up

Export Citation Format

Share Document