scholarly journals A New Label-Free and Contactless Bio-Tomographic Imaging with Miniaturized Capacitively-Coupled Spectroscopy Measurements

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3327
Author(s):  
Gege Ma ◽  
Manuchehr Soleimani
Keyword(s):  
Electrical Conductivity ◽  
Low Frequency ◽  
Small Scale ◽  
Imaging Method ◽  
Label Free ◽  
Capacitively Coupled ◽  
Biological Studies ◽  
Wide Range ◽  
Array Imaging ◽  
Imaging Sensor

A new bio-imaging method has been developed by introducing an experimental verification of capacitively coupled resistivity imaging in a small scale. This paper focuses on the 2D circular array imaging sensor as well as a 3D planar array imaging sensor with spectroscopic measurements in a wide range from low frequency to radiofrequency. Both these two setups are well suited for standard containers used in cell and culture biological studies, allowing for fully non-invasive testing. This is true as the capacitive based imaging sensor can extract dielectric spectroscopic images from the sample without direct contact with the medium. The paper shows the concept by deriving a wide range of spectroscopic information from biological test samples. We drive both spectra of electrical conductivity and the change rate of electrical conductivity with frequency as a piece of fundamentally important information. The high-frequency excitation allows the interrogation of critical properties that arise from the cell nucleus.

scholarly journals Separating and imaging diffractions of seismic waves in the full-azimuth dip-angle domain

2019 ◽  
Vol 17 (2) ◽  
pp. 339-356
Author(s):  
Chuangjian Li ◽  
Jingtao Zhao ◽  
Suping Peng ◽  
Xiaoqin Cui ◽  
Peng Lin
Keyword(s):  
Seismic Waves ◽  
Fresnel Zone ◽  
Specular Reflection ◽  
New Method ◽  
Small Scale ◽  
Imaging Method ◽  
Kirchhoff Migration ◽  
Strong Energy ◽  
Wide Range ◽  
Dip Angle

Abstract Seismic diffractions are ideal carriers of information on small-scale, discontinuous objects and can therefore be used to detect these geologic objects. However, recognizing diffractions is difficult because specular reflection with strong energy masks the weak diffraction. In this study, we propose a diffraction separation and imaging method based on a Mahalanobis-based and phase-based attenuation function used to modify the Kirchhoff migration formula in the full-azimuth dip-angle domain. In this domain, reflections are restricted to within the first Fresnel zone and are distributed in the vicinity of the stationary point, while diffractions are located across a wide range of azimuth and dip angles. Synthetic and field data applications suggest that this new method can effectively separate and image diffractions. The results also demonstrate the efficiency of the new method in clarifying subsurface small-scale objects, which can provide finer information about these structures for seismic interpretation.

scholarly journals Relating membrane potential to impedance spectroscopy

2019 ◽  
Vol 2 (1) ◽  
pp. 93-97 ◽  
Author(s):  
Eugen Gheorghiu
Keyword(s):  
Membrane Potential ◽  
Low Frequency ◽  
Lipid Vesicles ◽  
Living Cells ◽  
Label Free ◽  
Net Charge ◽  
Cell Parameters ◽  
Non Invasive ◽  
Wide Range ◽  
Cellular Medium

Abstract Non-invasive, label-free assessment of membrane potential of living cells is still a challenging task. The theory linking membrane potential to the low frequency α dispersion exhibited by suspensions of spherical shelled particles (presenting a net charge distribution on the inner side of the shell) has been pioneered in our previous studies with emphasis on the permittivity spectra. Whereas α dispersion is related to a rather large variation exhibited by the permittivity spectrum, we report that the related decrement presented by the impedance magnitude spectrum is either extremely small, or occurs (for large cells) at very small frequencies (~mHz) explaining the lack of experimental bioimpedance data on the matter. We stress that appropriate choice of the parameters (as revealed by the microscopic model) may enable access to membrane potential as well as to other relevant parameters when investigating living cells and charged lipid vesicles. We analyse the effect on the low frequency of the permittivity and impedance spectra of: I. Parameters pertaining to cell membrane i.e. (i) membrane potential (through the amount of the net charge on the inner side of the membrane), (ii) size of the cells/vesicles, (iii) conductivity of the membrane; II. Parameters of the extra cellular medium (viscosity and conductivity). The applicability of the study has far reaching implications for basic (life) sciences (providing non-invasive access to the dynamics of relevant cell parameters) as well as for biosensing applications, e.g. assessment of cytotoxicity of a wide range of stimuli.

The Attenuation of Very Low Frequency Brain Oscillations in Transitions from a Rest State to Active Attention

2009 ◽  
Vol 23 (4) ◽  
pp. 191-198 ◽  
Author(s):  
Suzannah K. Helps ◽  
Samantha J. Broyd ◽  
Christopher J. James ◽  
Anke Karl ◽  
Edmund J. S. Sonuga-Barke
Keyword(s):  
Brain Activity ◽  
Sampling Rate ◽  
Low Frequency ◽  
Future Research ◽  
Adhd Symptoms ◽  
Default Mode ◽  
Very Low Frequency ◽  
Wide Range ◽  
Interference Hypothesis ◽  
Mode Interference

Background: The default mode interference hypothesis ( Sonuga-Barke & Castellanos, 2007 ) predicts (1) the attenuation of very low frequency oscillations (VLFO; e.g., .05 Hz) in brain activity within the default mode network during the transition from rest to task, and (2) that failures to attenuate in this way will lead to an increased likelihood of periodic attention lapses that are synchronized to the VLFO pattern. Here, we tested these predictions using DC-EEG recordings within and outside of a previously identified network of electrode locations hypothesized to reflect DMN activity (i.e., S3 network; Helps et al., 2008 ). Method: 24 young adults (mean age 22.3 years; 8 male), sampled to include a wide range of ADHD symptoms, took part in a study of rest to task transitions. Two conditions were compared: 5 min of rest (eyes open) and a 10-min simple 2-choice RT task with a relatively high sampling rate (ISI 1 s). DC-EEG was recorded during both conditions, and the low-frequency spectrum was decomposed and measures of the power within specific bands extracted. Results: Shift from rest to task led to an attenuation of VLFO activity within the S3 network which was inversely associated with ADHD symptoms. RT during task also showed a VLFO signature. During task there was a small but significant degree of synchronization between EEG and RT in the VLFO band. Attenuators showed a lower degree of synchrony than nonattenuators. Discussion: The results provide some initial EEG-based support for the default mode interference hypothesis and suggest that failure to attenuate VLFO in the S3 network is associated with higher synchrony between low-frequency brain activity and RT fluctuations during a simple RT task. Although significant, the effects were small and future research should employ tasks with a higher sampling rate to increase the possibility of extracting robust and stable signals.

Radio and Electrical Measurements on Glacial Streams

1987 ◽  
Vol 33 (114) ◽  
pp. 239-242
Author(s):  
M. E. R. Walford
Keyword(s):  
Electrical Conductivity ◽  
Water Channel ◽  
Water System ◽  
Low Frequency ◽  
Water Channels ◽  
Radiative Loss ◽  
Radio Waves ◽  
Electrical Measurements ◽  
Water Conductivity ◽  
Glacier Surface

AbstractWe discuss the suggestion that small underwater transmitters might be used to illuminate the interior of major englacial water channels with radio waves. Once launched, the radio waves would naturally tend to be guided along the channels until attenuated by absorption and by radiative loss. Receivers placed within the channels or at the glacier surface could be used to detect the signals. They would provide valuable information about the connectivity of the water system. The electrical conductivity of the water is of crucial importance. A surface stream on Storglaciären, in Sweden, was found, using a low-frequency technique, to have a conductivity of approximately 4 × 10−4 S m−1. Although this is several hundred times higher than the conductivity of the surrounding glacier ice, the contrast is not sufficient to permit us simply to use electrical conductivity measurements to establish the connectivity of englacial water channels. However, the water conductivity is sufficiently small that, under favourable circumstances, radio signals should be detectable after travelling as much as a few hundred metres along an englacial water channel. In a preliminary field experiment, we demonstrated semi quantitatively that radio waves do indeed propagate as expected, at least in surface streams. We conclude that under-water radio transmitters could be of real practical value in the study of the englacial water system, provided that sufficiently robust devices can be constructed. In a subglacial channel, however, we expect the radio range would be much smaller, the environment much harsher, and the technique of less practical value.

scholarly journals Photonic Crystal Nanobeam Cavities for Nanoscale Optical Sensing: A Review

Micromachines ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 72 ◽  
Author(s):  
Da-Quan Yang ◽  
Bing Duan ◽  
Xiao Liu ◽  
Ai-Qiang Wang ◽  
Xiao-Gang Li ◽  
...  
Keyword(s):  
Photonic Crystal ◽  
Optical Waveguides ◽  
Optical Sensing ◽  
Early Stage ◽  
Disease Diagnosis ◽  
Label Free ◽  
Quality Factors ◽  
Integrated Sensor ◽  
Early Stage Disease ◽  
Wide Range

The ability to detect nanoscale objects is particular crucial for a wide range of applications, such as environmental protection, early-stage disease diagnosis and drug discovery. Photonic crystal nanobeam cavity (PCNC) sensors have attracted great attention due to high-quality factors and small-mode volumes (Q/V) and good on-chip integrability with optical waveguides/circuits. In this review, we focus on nanoscale optical sensing based on PCNC sensors, including ultrahigh figure of merit (FOM) sensing, single nanoparticle trapping, label-free molecule detection and an integrated sensor array for multiplexed sensing. We believe that the PCNC sensors featuring ultracompact footprint, high monolithic integration capability, fast response and ultrahigh sensitivity sensing ability, etc., will provide a promising platform for further developing lab-on-a-chip devices for biosensing and other functionalities.

Integrated Design and Multi-Objective Optimization of a Single Stage Heat-Pump Turbocompressor

2013 ◽  
Author(s):  
J. Schiffmann
Keyword(s):  
Design Optimization ◽  
High Efficiency ◽  
Integrated Design ◽  
Heat Pumps ◽  
Small Scale ◽  
Multi Objective Optimization ◽  
Design Constraints ◽  
Multi Objective ◽  
Wide Range ◽  
Standard Design

Small scale turbomachines in domestic heat pumps reach high efficiency and provide oil-free solutions which improve heat-exchanger performance and offer major advantages in the design of advanced thermodynamic cycles. An appropriate turbocompressor for domestic air based heat pumps requires the ability to operate on a wide range of inlet pressure, pressure ratios and mass flows, confronting the designer with the necessity to compromise between range and efficiency. Further the design of small-scale direct driven turbomachines is a complex and interdisciplinary task. Textbook design procedures propose to split such systems into subcomponents and to design and optimize each element individually. This common procedure, however, tends to neglect the interactions between the different components leading to suboptimal solutions. The authors propose an approach based on the integrated philosophy for designing and optimizing gas bearing supported, direct driven turbocompressors for applications with challenging requirements with regards to operation range and efficiency. Using previously validated reduced order models for the different components an integrated model of the compressor is implemented and the optimum system found via multi-objective optimization. It is shown that compared to standard design procedure the integrated approach yields an increase of the seasonal compressor efficiency of more than 12 points. Further a design optimization based sensitivity analysis allows to investigate the influence of design constraints determined prior to optimization such as impeller surface roughness, rotor material and impeller force. A relaxation of these constrains yields additional room for improvement. Reduced impeller force improves efficiency due to a smaller thrust bearing mainly, whereas a lighter rotor material improves rotordynamic performance. A hydraulically smoother impeller surface improves the overall efficiency considerably by reducing aerodynamic losses. A combination of the relaxation of the 3 design constraints yields an additional improvement of 6 points compared to the original optimization process. The integrated design and optimization procedure implemented in the case of a complex design problem thus clearly shows its advantages compared to traditional design methods by allowing a truly exhaustive search for optimum solutions throughout the complete design space. It can be used for both design optimization and for design analysis.

New insights on Laminaria digitata ultrastructure through combined conventional chemical fixation and cryofixation

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Christos Katsaros ◽  
Sophie Le Panse ◽  
Gillian Milne ◽  
Carl J. Carrano ◽  
Frithjof Christian Küpper
Keyword(s):  
Cell Wall ◽  
General Structure ◽  
Raw Material ◽  
Rocky Shores ◽  
Chemical Fixation ◽  
Laminaria Digitata ◽  
Vegetative Cells ◽  
Biological Studies ◽  
New Findings ◽  
Wide Range

Abstract The objective of the present study is to examine the fine structure of vegetative cells of Laminaria digitata using both chemical fixation and cryofixation. Laminaria digitata was chosen due to its importance as a model organism in a wide range of biological studies, as a keystone species on rocky shores of the North Atlantic, its use of iodide as a unique inorganic antioxidant, and its significance as a raw material for the production of alginate. Details of the fine structural features of vegetative cells are described, with particular emphasis on the differences between the two methods used, i.e. conventional chemical fixation and freeze-fixation. The general structure of the cells was similar to that already described, with minor differences between the different cell types. An intense activity of the Golgi system was found associated with the thick external cell wall, with large dictyosomes from which numerous vesicles and cisternae are released. An interesting type of cisternae was found in the cryofixed material, which was not visible with the chemical fixation. These are elongated structures, in sections appearing tubule-like, close to the external cell wall or to young internal walls. An increased number of these structures was observed near the plasmodesmata of the pit fields. They are similar to the “flat cisternae” found associated with the forming cytokinetic diaphragm of brown algae. Their possible role is discussed. The new findings of this work underline the importance of such combined studies which reveal new data not known until now using the old conventional methods. The main conclusion of the present study is that cryofixation is the method of choice for studying Laminaria cytology by transmission electron microscopy.

scholarly journals Broadband dielectric spectroscopy for monitoring temperature-dependent chloride ion motion in BiOCl plates

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Adrian Radoń ◽  
Dariusz Łukowiec ◽  
Patryk Włodarczyk
Keyword(s):  
Electrical Conductivity ◽  
Dielectric Spectroscopy ◽  
Low Frequency ◽  
Chloride Ion ◽  
Ion Source ◽  
Chloride Ions ◽  
Ion Concentration ◽  
Broadband Dielectric Spectroscopy ◽  
Free Chloride ◽  
Structure Rebuilding

AbstractThe dielectric properties and electrical conduction mechanism of bismuth oxychloride (BiOCl) plates synthesized using chloramine-T as the chloride ion source were investigated. Thermally-activated structure rebuilding was monitored using broadband dielectric spectroscopy, which showed that the onset temperature of this process was 283 K. This rebuilding was related to the introduction of free chloride ions into [Bi2O2]2+ layers and their growth, which increased the intensity of the (101) diffraction peak. The electrical conductivity and dielectric permittivity were related to the movement of chloride ions between plates (in the low-frequency region), the interplanar motion of Cl− ions at higher frequencies, vibrations of these ions, and charge carrier hopping at frequencies above 10 kHz. The influence of the free chloride ion concentration on the electrical conductivity was also described. Structure rebuilding was associated with a lower concentration of free chloride ions, which significantly decreased the conductivity. According to the analysis, the BiOCl plate conductivity was related to the movement of Cl− ions, not electrons.

scholarly journals A broadbanded pressure differential wave energy converter based on dielectric elastomer generators

2021 ◽  
Author(s):  
Michele Righi ◽  
Giacomo Moretti ◽  
David Forehand ◽  
Lorenzo Agostini ◽  
Rocco Vertechy ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Deformations ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Pressure Differential ◽  
Design Stage ◽  
Small Scale ◽  
Energy Converter ◽  
Wide Range ◽  
The Waves

AbstractDielectric elastomer generators (DEGs) are a promising option for the implementation of affordable and reliable sea wave energy converters (WECs), as they show considerable promise in replacing expensive and inefficient power take-off systems with cheap direct-drive generators. This paper introduces a concept of a pressure differential wave energy converter, equipped with a DEG power take-off operating in direct contact with sea water. The device consists of a closed submerged air chamber, with a fluid-directing duct and a deformable DEG power take-off mounted on its top surface. The DEG is cyclically deformed by wave-induced pressure, thus acting both as the power take-off and as a deformable interface with the waves. This layout allows the partial balancing of the stiffness due to the DEG’s elasticity with the negative hydrostatic stiffness contribution associated with the displacement of the water column on top of the DEG. This feature makes it possible to design devices in which the DEG exhibits large deformations over a wide range of excitation frequencies, potentially achieving large power capture in a wide range of sea states. We propose a modelling approach for the system that relies on potential-flow theory and electroelasticity theory. This model makes it possible to predict the system dynamic response in different operational conditions and it is computationally efficient to perform iterative and repeated simulations, which are required at the design stage of a new WEC. We performed tests on a small-scale prototype in a wave tank with the aim of investigating the fluid–structure interaction between the DEG membrane and the waves in dynamical conditions and validating the numerical model. The experimental results proved that the device exhibits large deformations of the DEG power take-off over a broad range of monochromatic and panchromatic sea states. The proposed model demonstrates good agreement with the experimental data, hence proving its suitability and effectiveness as a design and prediction tool.

Sign in / Sign up

Export Citation Format

Share Document