scholarly journals Comparison of Gas Sensing Properties of Reduced Graphene Oxide Obtained by Two Different Methods

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3175
Author(s):  
Sabina Drewniak ◽  
Marcin Procek ◽  
Roksana Muzyka ◽  
Tadeusz Pustelny
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sorption Method ◽  
Reduced Graphene ◽  
Gaseous Atmospheres

In this study, the sensitivity of reduced graphene oxide structures (rGO) to the action of selected gases (especially hydrogen, but also nitrogen dioxide and ammonia) was examined. Two sensing structures, based on rGO structures, obtained by different methods of oxidation (the modified Hummers, and the modified Tour’s method respectively), were investigated. We show here that the method used for the oxidation of rGO influences the sensitivity of the sensing structure during contact with various gaseous atmospheres. We performed our experiments in the atmosphere, containing hydrogen in a concentration range from 0 to 4% in nitrogen or synthetic air, both in dry and wet conditions. The temperature range was from 50 °C to 190 °C. Finally, we checked how the resistance of the samples changes when the other gases (NO2, NH3) appear in tested gas mixtures. The gas investigations were supplemented by the characterization of rGOs materials using scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and N2 sorption method.

scholarly journals Reduced Graphene Oxide–Epoxy Grafted Poly(Styrene-Co-Acrylate) Composites for Corrosion Protection of Mild Steel

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 666
Author(s):  
Xinchuan Fan ◽  
Yue Hu ◽  
Yijun Zhang ◽  
Jiachen Lu ◽  
Xiaofeng Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Corrosion Properties ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Scanning Electron

Reduced graphene oxide–epoxy grafted poly(styrene-co-acrylate) composites (GESA) were prepared by anchoring different amount of epoxy modified poly(styrene-co-acrylate) (EPSA) onto reduced graphene oxide (rGO) sheets through π–π electrostatic attraction. The GESA composites were characterized by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The anti-corrosion properties of rGO/EPSA composites were evaluated by electro-chemical impedance spectroscopy (EIS) in hydroxyl-polyacrylate coating, and the results revealed that the corrosion rate was decreased from 3.509 × 10−1 to 1.394 × 10−6 mm/a.

Preparation and Characterization of Reduced Graphene Oxide Based Natural Rubber Nanocomposites

2020 ◽  
Vol 35 (5) ◽  
pp. 493-502
Author(s):  
F. Shahamatifard ◽  
D. Rodrigue ◽  
K. Park ◽  
S. Frikha ◽  
F. Mighri
Keyword(s):  
Graphene Oxide ◽  
Natural Rubber ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Second Step ◽  
X Ray ◽  
Reduced Graphene ◽  
Rubber Nanocomposites ◽  
Internal Mixer

Abstract This work describes the effect of reduced graphene oxide (RGO) addition in natural rubber (NR). Firstly, RGO was synthesized based on the improved Hummer’s method then characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) to confirm that the RGO surface contains hydroxyl, epoxy, and carboxyl functional groups to improve graphene interaction with the NR matrix. In a second step, the synthesized RGO was predispersed in NR latex using the co-coagulation technique then added at different amounts (0 to 2 parts per hundred rubber (phr)) to a basic NR formulation and compounded in an internal mixer. The results show that the crosslink density of the developed NR/RGO nanocomposites increased by 65% for RGO concentration of 2.0 phr. For the same RGO concentration, a significant increase in tensile strength (53%) and Young’s modulus (31%) were also observed. Finally, a significant improvement (26%) of the thermal conductivity was obtained with the addition of only 0.5 phr of RGO.

Reduced Graphene Oxide Supported Molybdenum Oxide Hybrid Nanocomposites: High Performance Electrode Material for Supercapacitor and Photocatalytic Applications

2020 ◽  
Vol 20 (7) ◽  
pp. 4035-4046
Author(s):  
Rengasamy Dhanabal ◽  
Dhanasekaran Naveena ◽  
Sivan Velmathi ◽  
Arumugam Chandra Bose
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Hybrid Nanocomposites ◽  
X Ray ◽  
Supercapacitor Application ◽  
Quenching Effect ◽  
Reduced Graphene

Using a simple solution based synthesis route, hexagonal MoO3 (h-MoO3) nanorods on reduced graphene oxide (RGO) sheets were prepared. The structure and morphology of resulting RGO-MoO3 nanocomposite were characterized using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), transmission electron microscopy (TEM) and field emission scanning electron microscopy (FESEM). The optical property was studied using UV-Visible diffuse reflectance spectroscopy (UV-Vis DRS) and photoluminescence spectroscopy (PL). The RGO-MoO3 nanocomposites were used as an electrode for supercapacitor application and photocatalyst for photodegradation of methylene blue (MB) and rhodamine B (RhB) under visible light irradiation. We demonstrated that the RGO-MoO3 electrode is capable of delivering high specific capacitance of 134 F/g at current density of 1 A/g with outstanding cyclic stability for 2000 cycles. The RGOMoO3 photocatalyst degrades 95% of MB dye within 90 min, and a considerable recyclability up to 4 cycles was observed. The quenching effect of scavengers test confirms holes are main reactive species in the photocatalytic degradation of MB. Further, the charge transfer process between RGO and MoO3 was schematically demonstrated.

scholarly journals Effects of Different TiO2 Particle Sizes on the Microstructure and Optical Limiting Properties of TiO2/Reduced Graphene Oxide Nanocomposites

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 730 ◽  
Author(s):  
Yuyu Ren ◽  
Lili Zhao ◽  
Yang Zou ◽  
Lixin Song ◽  
Ningning Dong ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Optical Limiting ◽  
Tio2 Particle ◽  
Tetrabutyl Titanate ◽  
Particle Sizes ◽  
X Ray ◽  
Reduced Graphene ◽  
Source Materials

TiO2/reduced graphene oxide (rGO) nanocomposites with two different TiO2 particle sizes were synthesized by a facile hydrothermal method using two different source materials of Ti: tetrabutyl titanate (TBT) and commercial TiO2 powder (P25). For respective series with the same source materials, we investigated additions that optimized the nonlinear optical properties (NLO) and optical limiting (OL) performances, and we explored the relationships between structural diversity and performance. Several characterization techniques, including X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, and diffuse reflectance ultraviolet-visible spectroscopy (UV-Vis) were conducted to confirm the microstructures and chemical states of as-prepared materials. This indicated the existence of the Ti–O–C bond between rGO sheets and TiO2 particles and the reduction from precursor graphene oxide (GO) to rGO. The results of UV-Vis spectra revealed that the TiO2/rGO nanocomposites showed smaller band gaps than bare TiO2. A nanosecond open-aperture Z-scan technique at 1064 nm was applied to investigate NLO and OL properties. TiO2/rGO nanocomposites exhibited enhanced NLO and OL performances, arising from synergistic effects, compared to individual components. The TBT series samples performed better than the P25 series, presumably relevant to dimensional effects.

Study on Magnetic Properties of Na-Doped rGO Prepared from Coconut Shells

2020 ◽  
Vol 855 ◽  
pp. 160-165
Author(s):  
Deril Ristiani ◽  
Niken Sylvia Puspitasari ◽  
Retno Asih ◽  
Fahmi Astuti ◽  
Malik Anjelh Baqiya ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Mixing Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Reduced Graphene ◽  
Naoh Solution ◽  
Na Ions ◽  
Diffraction Peaks ◽  
Coconut Shells

Na-doped reduced graphene oxide (Na-rGO) was prepared by wet mixing process of the reduced graphene oxide (rGO) in NaOH solution. The results showed that the rGO doped with Na ions can increase its magnetization approximately 2 times greater than that in rGO without doping. Saturation magnetization (Ms) for rGO and Na-rGO samples are 0.017 emu/g and 0.037 emu/g, respectively. The increasing value of magnetization is suggested to be due to defect presented in the Na-rGO samples. Both samples, rGO and Na-rGO, have the similar XRD (X-ray Diffraction) spectra that is marked by two characteristic diffraction peaks of rGO, which are associated with [002] and [10] planes, followed by the increasing inter-planar distance in Na-rGO samples which might be due to Na ions intercalation into rGO sheets, confirmed by the energy-dispersive X-ray (EDX) result revealing the presence of Na atoms in rGO.

scholarly journals X-ray diffraction investigations of nanostructured ZnO coated with reduced graphene oxide.

2019 ◽  
Vol 1292 ◽  
pp. 012011 ◽  
Author(s):  
I Boukhoubza ◽  
M Khenfouch ◽  
M Achehboune ◽  
B M Mothudi ◽  
I Zorkani ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Reduced Graphene

Facile Synthesis of Modified MnO2/Reduced Graphene Oxide Nanocomposites and their Application in Supercapacitors

NANO ◽  
2020 ◽  
Vol 15 (08) ◽  
pp. 2050099
Author(s):  
Lijun Chen ◽  
Hongfeng Yin ◽  
Yuchao Zhang ◽  
Huidong Xie
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Specific Capacitance ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Electrode Materials ◽  
Normal Pressure ◽  
X Ray ◽  
Assembly Method ◽  
Reduced Graphene

Herein, KH-550 was used as surface modifier to prepare modified MnO2/reduced graphene oxide (M-MnO2/rGO) composite electrode materials by utilizing electrostatic interaction at low temperature and normal pressure. X-ray diffraction, scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy were adopted to characterize the material’s phase, morphology, and valence state of elements. The electrochemical properties of the material were measured using a three-electrode system. The results indicate a decrease in the size of the modified MnO2 particles, and that they were uniformly distributed on the rGO sheets. The M-MnO2/rGO composite attained a specific capacitance of 326[Formula: see text]F[Formula: see text]g[Formula: see text] in a solution of 1[Formula: see text]mol[Formula: see text]L[Formula: see text] Na2SO4 at a current density of 0.5[Formula: see text]A[Formula: see text]g[Formula: see text]. The specific capacitance of the material was 92.4% after 1000 cycles. The electrostatic self-assembly method effectively solved the problem of reducing the cycling stability while improving the specific capacitance of the composite materials, and further improved the possibility of applying MnO2/rGO in the field of supercapacitors.

Fabrication of Nickel Sulfide/Nitrogen-Doped Reduced Graphene Oxide Nanocomposite as Anode Material for Lithium-Ion Batteries and Its Electrochemical Performance

2020 ◽  
Vol 20 (11) ◽  
pp. 6782-6787
Author(s):  
Yeon-Ju Lee ◽  
Tae-Hyun Ha ◽  
Gyu-Bong Cho ◽  
Ki-Won Kim ◽  
Jou-Hyeon Ahn ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Lithium Ion ◽  
Treatment Method ◽  
Retention Capacity ◽  
Graphene Nanocomposites ◽  
X Ray ◽  
Nitrogen Doped ◽  
Reduced Graphene

In this study, NiS/graphene nanocomposites were synthesized by simple heat treatment method of three graphene materials (graphene oxide (GO), reduced graphene oxide (rGO) and nitrogen-doped graphene oxide (N-rGO)) and NiS precursor. The morphology and crystal structure of NiS/graphene nanocomposites were characterized using field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Electrochemical properties were also investigated. NiS/graphene nanocomposites homogeneously wrapped by graphene materials have been successfully manufactured. Among the three nanocomposites, NiS/N-rGO nanocomposite exhibited the highest initial and retention capacity in discharge, respectively, of 1240 mAh/g and 467 mAh/g up to 100 cycles at 0.5 C.

Simplified Synthesis of 3D Flexible Reduced Graphene Oxide-Wrapped NiCo2O4 Nanowires for High-Performance Supercapacitor

2018 ◽  
Vol 10 (3) ◽  
pp. 358-364 ◽  
Author(s):  
Chao Pan ◽  
Hongyu Sun ◽  
Jingyi Gao ◽  
Yucai Hu ◽  
Jing Wang
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Current Density ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
High Current Density ◽  
Three Dimensional ◽  
Simple Method ◽  
X Ray ◽  
Reduced Graphene

We introduced a simple method to construct novel three-dimensional (3D) flexible hierarchical nanocomposites by combining (1D) NiCo2O4 nanowires with 2D reduced graphene oxide (rGO) sheets. The hierarchical nanocomposite structure of rGO-wrapped NiCo2O4 (rGO-NiCo2O4) was confirmed by X-ray diffraction (XRD), Raman spectra, scanning electron microscopy (SEM), transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS). The results indicated that NiCo2O4 nanowires were successfully wrapped in rGO and the morphology of the rGO-NiCo2O4 showed a three-dimensional porous structure with NiCo2O4 being homogeneously distributed in the rGO. Given their apparent advantages, these two different nanostructures were evaluated as electrodes for high-performance supercapacitors. These electrodes exhibited a high capacitance of 1824.8 F·g–1 at a current density of 0.5 A·g–1, and an excellent cycling performance extending to 5000 cycles at a high current density of 4 A·g–1. Our results clearly demonstrate that rGO sheets on NiCo2O4 nanowires can substantially improve the capacitive performance of materials and ultimately increase the cycling stability of supercapacitors. The hierarchical binary nanocomposites show excellent electrochemical properties for energy storage applications, evidencing their potential application as supercapacitors.

Sign in / Sign up

Export Citation Format

Share Document