scholarly journals Performance of a Low-Cost Sensor Community Air Monitoring Network in Imperial County, CA

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3031
Author(s):  
Paul English ◽  
Heather Amato ◽  
Esther Bejarano ◽  
Graeme Carvlin ◽  
Humberto Lugo ◽  
...  
Keyword(s):  
Real Time ◽  
Low Cost ◽  
Monitoring Network ◽  
Data Interpretation ◽  
Air Monitoring ◽  
Least Square ◽  
Quality Data ◽  
Monitoring Networks ◽  
Time Data ◽  
Ordinary Least Square Regression

Air monitoring networks developed by communities have potential to reduce exposures and affect environmental health policy, yet there have been few performance evaluations of networks of these sensors in the field. We developed a network of over 40 air sensors in Imperial County, CA, which is delivering real-time data to local communities on levels of particulate matter. We report here on the performance of the Network to date by comparing the low-cost sensor readings to regulatory monitors for 4 years of operation (2015–2018) on a network-wide basis. Annual mean levels of PM10 did not differ statistically from regulatory annual means, but did for PM2.5 for two out of the 4 years. R2s from ordinary least square regression results ranged from 0.16 to 0.67 for PM10, and increased each year of operation. Sensor variability was higher among the Network monitors than the regulatory monitors. The Network identified a larger number of pollution episodes and identified under-reporting by the regulatory monitors. The participatory approach of the project resulted in increased engagement from local and state agencies and increased local knowledge about air quality, data interpretation, and health impacts. Community air monitoring networks have the potential to provide real-time reliable data to local populations.

CAMS-Net: The Clean Air Monitoring and Solutions Network

2021 ◽  
Author(s):  
Daniel Westervelt ◽  
Celeste McFarlane ◽  
Faye McNeill ◽  
R (Subu) Subramanian ◽  
Mike Giordano ◽  
...  
Keyword(s):  
Air Pollution ◽  
Air Quality ◽  
Linear Regression ◽  
Multiple Linear Regression ◽  
Low Cost ◽  
Air Monitoring ◽  
Quality Data ◽  
Calibration Methods ◽  
The World ◽  
Clean Air

<p>There is a severe lack of air pollution data around the world. This includes large portions of low- and middle-income countries (LMICs), as well as rural areas of wealthier nations as monitors tend to be located in large metropolises. Low cost sensors (LCS) for measuring air pollution and identifying sources offer a possible path forward to remedy the lack of data, though significant knowledge gaps and caveats remain regarding the accurate application and interpretation of such devices.</p><p>The Clean Air Monitoring and Solutions Network (CAMS-Net) establishes an international network of networks that unites scientists, decision-makers, city administrators, citizen groups, the private sector, and other local stakeholders in co-developing new methods and best practices for real-time air quality data collection, data sharing, and solutions for air quality improvements. CAMS-Net brings together at least 32 multidisciplinary member networks from North America, Europe, Africa, and India. The project establishes a mechanism for international collaboration, builds technical capacity, shares knowledge, and trains the next generation of air quality practitioners and advocates, including domestic and international graduate students and postdoctoral researchers. </p><p>Here we present some preliminary research accelerated through the CAMS-Net project. Specifically, we present LCS calibration methodology for several co-locations in LMICs (Accra, Ghana; Kampala, Uganda; Nairobi, Kenya; Addis Ababa, Ethiopia; and Kolkata, India), in which reference BAM-1020 PM2.5 monitors were placed side-by-side with LCS. We demonstrate that both simple multiple linear regression calibration methods for bias-correcting LCS and more complex machine learning methods can reduce bias in LCS to close to zero, while increasing correlation. For example, in Kampala, Raw PurpleAir PM2.5 data are strongly correlated with the BAM-1020 PM2.5 (r<sup>2</sup> = 0.88), but have a mean bias of approximately 12 μg m<sup>-3</sup>. Two calibration models, multiple linear regression and a random forest approach, decrease mean bias from 12 μg m<sup>-3 </sup>to -1.84 µg m<sup>-3</sup> or less and improve the the r<sup>2</sup> from 0.88 to 0.96. We find similar performance in several other regions of the world. Location-specific calibration of low-cost sensors is necessary in order to obtain useful data, since sensor performance is closely tied to environmental conditions such as relative humidity. This work is a first step towards developing a database of region-specific correction factors for low cost sensors, which are exploding in popularity globally and have the potential to close the air pollution data gap especially in resource-limited countries. </p><p> </p><p> </p>

scholarly journals Design of an IoT based Real Time Environment Monitoring System using Legacy Sensors

2018 ◽  
Vol 210 ◽  
pp. 03008
Author(s):  
Aparajita Das ◽  
Manash Pratim Sarma ◽  
Kandarpa Kumar Sarma ◽  
Nikos Mastorakis
Keyword(s):  
Air Pollution ◽  
Light Intensity ◽  
Real Time ◽  
Environmental Conditions ◽  
Low Cost ◽  
Environment Monitoring ◽  
Time Data ◽  
Graphical Information ◽  
Real Time Data ◽  
Sun Light

This paper describes the design of an operative prototype based on Internet of Things (IoT) concepts for real time monitoring of various environmental conditions using certain commonly available and low cost sensors. The various environmental conditions such as temperature, humidity, air pollution, sun light intensity and rain are continuously monitored, processed and controlled by an Arduino Uno microcontroller board with the help of several sensors. Captured data are broadcasted through internet with an ESP8266 Wi-Fi module. The projected system delivers sensors data to an API called ThingSpeak over an HTTP protocol and allows storing of data. The proposed system works well and it shows reliability. The prototype has been used to monitor and analyse real time data using graphical information of the environment.

scholarly journals REAL-TIME ENVIRONMENTAL SENSORS TO IMPROVE HEALTH IN THE SENSING CITY

2016 ◽  
Vol XLI-B2 ◽  
pp. 729-733 ◽  
Author(s):  
L. Marek ◽  
M. Campbell ◽  
M. Epton ◽  
M. Storer ◽  
S. Kingham
Keyword(s):  
Quality Of Life ◽  
Air Pollution ◽  
Air Quality ◽  
Real Time ◽  
Low Cost ◽  
Monitoring Network ◽  
Environmental Data ◽  
Chronic Obstructive ◽  
Actual Usage

The opportunity of an emerging smart city in post-disaster Christchurch has been explored as a way to improve the quality of life of people suffering Chronic Obstructive Pulmonary Disease (COPD), which is a progressive disease that affects respiratory function. It affects 1 in 15 New Zealanders and is the 4th largest cause of death, with significant costs to the health system. While, cigarette smoking is the leading cause of COPD, long-term exposure to other lung irritants, such as air pollution, chemical fumes, or dust can also cause and exacerbate it. Currently, we do know little what happens to the patients with COPD after they leave a doctor’s care. By learning more about patients’ movements in space and time, we can better understand the impacts of both the environment and personal mobility on the disease. This research is studying patients with COPD by using GPS-enabled smartphones, combined with the data about their spatiotemporal movements and information about their actual usage of medication in near real-time. We measure environmental data in the city, including air pollution, humidity and temperature and how this may subsequently be associated with COPD symptoms. In addition to the existing air quality monitoring network, to improve the spatial scale of our analysis, we deployed a series of low-cost Internet of Things (IoT) air quality sensors as well. The study demonstrates how health devices, smartphones and IoT sensors are becoming a part of a new health data ecosystem and how their usage could provide information about high-risk health hotspots, which, in the longer term, could lead to improvement in the quality of life for patients with COPD.

scholarly journals Low-Cost Air Quality Sensors: One-Year Field Comparative Measurement of Different Gas Sensors and Particle Counters with Reference Monitors at Tušimice Observatory

Atmosphere ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 492 ◽  
Author(s):  
Petra Bauerová ◽  
Adriana Šindelářová ◽  
Štěpán Rychlík ◽  
Zbyněk Novák ◽  
Josef Keder
Keyword(s):  
Air Quality ◽  
Gas Sensors ◽  
Low Cost ◽  
Monitoring Network ◽  
Field Testing ◽  
Ambient Air ◽  
Monitoring Networks ◽  
Comparative Measurement ◽  
One Year ◽  
Pm2.5 And Pm10

With attention increasing regarding the level of air pollution in different metropolitan and industrial areas worldwide, interest in expanding the monitoring networks by low-cost air quality sensors is also increasing. Although the role of these small and affordable sensors is rather supplementary, determination of the measurement uncertainty is one of the main questions of their applicability because there is no certificate for quality assurance of these non-reference technologies. This paper presents the results of almost one-year field testing measurements, when the data from different low-cost sensors (for SO2, NO2, O3, and CO: Cairclip, Envea, FR; for PM1, PM2.5, and PM10: PMS7003, Plantower, CHN, and OPC-N2, Alphasense, UK) were compared with co-located reference monitors used within the Czech national ambient air quality monitoring network. The results showed that in addition to the given reduced measurement accuracy of the sensors, the data quality depends on the early detection of defective units and changes caused by the effect of meteorological conditions (effect of air temperature and humidity on gas sensors and effect of air humidity with condensation conditions on particle counters), or by the interference of different pollutants (especially in gas sensors). Comparative measurement is necessary prior to each sensor’s field applications.

The Design of Elevator Monitoring Terminal Based on the GPRS

2013 ◽  
Vol 313-314 ◽  
pp. 1180-1183
Author(s):  
Qi Zhi Fang ◽  
Yong Zhe Ge ◽  
Hong Yu Xu
Keyword(s):  
Real Time ◽  
Monitoring System ◽  
High Reliability ◽  
Low Cost ◽  
Monitoring Network ◽  
Wireless Monitoring ◽  
Management Platform ◽  
Management Quality ◽  
Ip Transport ◽  
Development Prospects

The elevator monitoring system of elevator is an integrated elevator management platform that can realize fault for alarm, rescuing trapped persons, daily management, quality evaluation and preventing hidden trouble by using C8051f060 MCU as the control core to sensor and collect the elevator operation data, with built-in TCP/IP transport protocol and with HuaWei GTM900C GPRS module to realize all kinds of data monitoring of the elevator, and the transmitting of the data to processing server through the network . This paper mainly introduces the formation of wireless monitoring network system and communication protocol construction, and especially analyzes the function and the system architecture of the wireless communication terminal in real-time monitoring. GPRS can not only satisfy the requirement of real-time elevator monitoring system, with low cost and high reliability but can also effectively avoid a variety of problems that are caused by transmitting the alarm data through cables . This system provides many valuable experiences for the development of unattended system, and it has a broad development prospects.

scholarly journals Edge Computing Based IoT Architecture for Low Cost Air Pollution Monitoring Systems: A Comprehensive System Analysis, Design Considerations & Development

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 3021 ◽  
Author(s):  
Zeba Idrees ◽  
Zhuo Zou ◽  
Lirong Zheng
Keyword(s):  
Air Quality ◽  
Power Consumption ◽  
Real Time ◽  
Low Cost ◽  
Edge Computing ◽  
Quality Monitoring ◽  
Quality Data ◽  
Monitoring Systems ◽  
Air Quality Monitoring ◽  
Computing Device

With the swift growth in commerce and transportation in the modern civilization, much attention has been paid to air quality monitoring, however existing monitoring systems are unable to provide sufficient spatial and temporal resolutions of the data with cost efficient and real time solutions. In this paper we have investigated the issues, infrastructure, computational complexity, and procedures of designing and implementing real-time air quality monitoring systems. To daze the defects of the existing monitoring systems and to decrease the overall cost, this paper devised a novel approach to implement the air quality monitoring system, employing the edge-computing based Internet-of-Things (IoT). In the proposed method, sensors gather the air quality data in real time and transmit it to the edge computing device that performs necessary processing and analysis. The complete infrastructure & prototype for evaluation is developed over the Arduino board and IBM Watson IoT platform. Our model is structured in such a way that it reduces the computational burden over sensing nodes (reduced to 70%) that is battery powered and balanced it with edge computing device that has its local data base and can be powered up directly as it is deployed indoor. Algorithms were employed to avoid temporary errors in low cost sensor, and to manage cross sensitivity problems. Automatic calibration is set up to ensure the accuracy of the sensors reporting, hence achieving data accuracy around 75–80% under different circumstances. In addition, a data transmission strategy is applied to minimize the redundant network traffic and power consumption. Our model acquires a power consumption reduction up to 23% with a significant low cost. Experimental evaluations were performed under different scenarios to validate the system’s effectiveness.

iPOS–an integrated production operation solution for Longtom Field

2011 ◽  
Vol 51 (1) ◽  
pp. 259
Author(s):  
Rajesh Trivedi ◽  
Shripad Biniwale ◽  
Adil Jabur
Keyword(s):  
Data Acquisition ◽  
Real Time ◽  
Joint Venture ◽  
Direct Access ◽  
Quality Data ◽  
Processing Plant ◽  
Production Operation ◽  
Time Data ◽  
Integrated Production ◽  
Real Time Data

With a vision of innovation, integrity and agility, Nexus Energy began first production of Longtom field in October 2009. The Longtom gas field is located in the Gippsland Basin, offshore Victoria where the produced gas is transported to Santos’ Patricia Baleen gas processing plant. All production data is acquired by Santos with the supervisory control and data acquisition (SCADA) system. The challenge for Nexus Energy was to monitor the field remotely in the absence of a data historian and to support the operational people proactively. Data acquisition from Santos, validation, and storage in a secured centralised repository were therefore key tasks. A system was needed that would not only track accurate production volumes to meet the daily contractual quantity (DCQ) production targets but that would also be aligned with Nexus’s vision for asset optimisation. We describe how real-time data is acquired, validated, and stored automatically in the absence of a data historian for Longtom field, and how the deployed system provides a framework for an integrated Production Operation System (iPOS). The solution uses an integrated methodology that allows effective monitoring of real-time data trends to anticipate and prevent potential well and equipment problems, thus assisting in meeting DCQ targets and providing effective analysis techniques for decision making. Based on full workflow automation, the system is deployed for acquisition, allocation, reporting and analysis. This has increased accuracy, accountability and timely availability of quality data, which has helped Nexus improve productivity. The comprehensive reporting tool provides access to operational and production reports via email for managers, output reports in various formats for joint venture partners, and nontechnical users without direct access to the core application. A powerful surveillance tool, integrated with the operational database, provides alarms and notifications on operation issues, which helps engineers make proactive operational decisions. The framework allows a streamlined data flow for dynamic updates of well and simulation models, improving process integration and reducing the runtime cycle.

scholarly journals Progressive System: A Deep-Learning Framework for Real-Time Data in Industrial Production

Processes ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 649
Author(s):  
Yifeng Liu ◽  
Wei Zhang ◽  
Wenhao Du
Keyword(s):  
Deep Learning ◽  
Real Time ◽  
Large Scale ◽  
Quality Data ◽  
Time Data ◽  
High Quality ◽  
Real Time System ◽  
High Quality Data ◽  
Learning Framework ◽  
Data Accumulation

Deep learning based on a large number of high-quality data plays an important role in many industries. However, deep learning is hard to directly embed in the real-time system, because the data accumulation of the system depends on real-time acquisitions. However, the analysis tasks of such systems need to be carried out in real time, which makes it impossible to complete the analysis tasks by accumulating data for a long time. In order to solve the problems of high-quality data accumulation, high timeliness of the data analysis, and difficulty in embedding deep-learning algorithms directly in real-time systems, this paper proposes a new progressive deep-learning framework and conducts experiments on image recognition. The experimental results show that the proposed framework is effective and performs well and can reach a conclusion similar to the deep-learning framework based on large-scale data.

scholarly journals Semantic Traffic Sensor Data: The TRAFAIR Experience

2020 ◽  
Vol 10 (17) ◽  
pp. 5882
Author(s):  
Federico Desimoni ◽  
Sergio Ilarri ◽  
Laura Po ◽  
Federica Rollo ◽  
Raquel Trillo-Lado
Keyword(s):  
Air Quality ◽  
Real Time ◽  
Smart Cities ◽  
Low Cost ◽  
Semantic Annotation ◽  
Open Data ◽  
Transportation Systems ◽  
Sensor Data ◽  
Time Data ◽  
Future Evolution

Modern cities face pressing problems with transportation systems including, but not limited to, traffic congestion, safety, health, and pollution. To tackle them, public administrations have implemented roadside infrastructures such as cameras and sensors to collect data about environmental and traffic conditions. In the case of traffic sensor data not only the real-time data are essential, but also historical values need to be preserved and published. When real-time and historical data of smart cities become available, everyone can join an evidence-based debate on the city’s future evolution. The TRAFAIR (Understanding Traffic Flows to Improve Air Quality) project seeks to understand how traffic affects urban air quality. The project develops a platform to provide real-time and predicted values on air quality in several cities in Europe, encompassing tasks such as the deployment of low-cost air quality sensors, data collection and integration, modeling and prediction, the publication of open data, and the development of applications for end-users and public administrations. This paper explicitly focuses on the modeling and semantic annotation of traffic data. We present the tools and techniques used in the project and validate our strategies for data modeling and its semantic enrichment over two cities: Modena (Italy) and Zaragoza (Spain). An experimental evaluation shows that our approach to publish Linked Data is effective.

Sign in / Sign up

Export Citation Format

Share Document