scholarly journals Thin Film Encapsulation for RF MEMS in 5G and Modern Telecommunication Systems

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2133 ◽  
Author(s):  
Anna Persano ◽  
Fabio Quaranta ◽  
Antonietta Taurino ◽  
Pietro Aleardo Siciliano ◽  
Jacopo Iannacci
Keyword(s):  
Thin Film ◽  
Microelectromechanical Systems ◽  
Rf Mems ◽  
Sacrificial Layer ◽  
Three Dimensional ◽  
Telecommunication Systems ◽  
Rf Performance ◽  
Three Dimensional Finite Element ◽  
The Impact ◽  
Thin Film Encapsulation

In this work, SiNx/a-Si/SiNx caps on conductive coplanar waveguides (CPWs) are proposed for thin film encapsulation of radio-frequency microelectromechanical systems (RF MEMS), in view of the application of these devices in fifth generation (5G) and modern telecommunication systems. Simplification and cost reduction of the fabrication process were obtained, using two etching processes in the same barrel chamber to create a matrix of holes through the capping layer and to remove the sacrificial layer under the cap. Encapsulating layers with etch holes of different size and density were fabricated to evaluate the removal of the sacrificial layer as a function of the percentage of the cap perforated area. Barrel etching process parameters also varied. Finally, a full three-dimensional finite element method-based simulation model was developed to predict the impact of fabricated thin film encapsulating caps on RF performance of CPWs.

Modeling of a One-Sided Bonded and Rigid Constraint Using Beam Theory

2008 ◽  
Vol 75 (3) ◽  
Author(s):  
Peter J. Ryan ◽  
George G. Adams ◽  
Nicol E. McGruer
Keyword(s):  
Boundary Conditions ◽  
Microelectromechanical Systems ◽  
Three Dimensional ◽  
Beam Theory ◽  
Rotational Stiffness ◽  
Element Analysis ◽  
Transverse Loads ◽  
Rigid Constraint ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In beam theory, constraints can be classified as fixed/pinned depending on whether the rotational stiffness of the support is much greater/less than the rotational stiffness of the freestanding portion. For intermediate values of the rotational stiffness of the support, the boundary conditions must account for the finite rotational stiffness of the constraint. In many applications, particularly in microelectromechanical systems and nanomechanics, the constraints exist only on one side of the beam. In such cases, it may appear at first that the same conditions on the constraint stiffness hold. However, it is the purpose of this paper to demonstrate that even if the beam is perfectly bonded on one side only to a completely rigid constraining surface, the proper model for the boundary conditions for the beam still needs to account for beam deformation in the bonded region. The use of a modified beam theory, which accounts for bending, shear, and extensional deformation in the bonded region, is required in order to model this behavior. Examples are given for cantilever, bridge, and guided structures subjected to either transverse loads or residual stresses. The results show significant differences from the ideal bond case. Comparisons made to a three-dimensional finite element analysis show a good agreement.

RF-MEMS Components and Networks for High-Performance Reconfigurable Telecommunication and Wireless Systems

2012 ◽  
Vol 81 ◽  
pp. 65-74 ◽  
Author(s):  
Jacopo Iannacci ◽  
Giuseppe Resta ◽  
Paola Farinelli ◽  
Roberto Sorrentino
Keyword(s):  
High Performance ◽  
Microelectromechanical Systems ◽  
Rf Mems ◽  
Low Cost ◽  
Impedance Matching ◽  
Phase Shifters ◽  
Rf Systems ◽  
Mems Technology ◽  
And Performance ◽  
Rf Performance

MEMS (MicroElectroMechanical-Systems) technology applied to the field of Radio Frequency systems (i.e. RF-MEMS) has emerged in the last 10-15 years as a valuable and viable solution to manufacture low-cost and very high-performance passive components, like variable capacitors, inductors and micro-relays, as well as complex networks, like tunable filters, reconfigurable impedance matching networks and phase shifters, and so on. The availability of such components and their integration within RF systems (e.g. radio transceivers, radars, satellites, etc.) enables boosting the characteristics and performance of telecommunication systems, addressing for instance a significant increase of their reconfigurability. The benefits resulting from the employment of RF-MEMS technology are paramount, being some of them the reduction of hardware redundancy and power consumption, along with the operability of the same RF system according to multiple standards. After framing more in detail the whole context of RF MEMS technology, this paper will provide a brief introduction on a typical RF-MEMS technology platform. Subsequently, some relevant examples of lumped RF MEMS passive elements and complex reconfigurable networks will be reported along with their measured RF performance and characteristics.

scholarly journals Focality of the Induced E-Field Is a Contributing Factor in the Choice of TMS Parameters: Evidence from a 3D Computational Model of the Human Brain

2020 ◽  
Vol 10 (12) ◽  
pp. 1010
Author(s):  
Deepika Konakanchi ◽  
Amy L. de Jongh Curry ◽  
Robert S. Waters ◽  
Shalini Narayana
Keyword(s):  
Spatial Distribution ◽  
Three Dimensional ◽  
Fem Simulation ◽  
Element Model ◽  
Brain Areas ◽  
Invasive Approach ◽  
Non Invasive ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
The Impact

Transcranial magnetic stimulation (TMS) is a promising, non-invasive approach in the diagnosis and treatment of several neurological conditions. However, the specific results in the cortex of the magnitude and spatial distribution of the secondary electrical field (E-field) resulting from TMS at different stimulation sites/orientations and varied TMS parameters are not clearly understood. The objective of this study is to identify the impact of TMS stimulation site and coil orientation on the induced E-field, including spatial distribution and the volume of activation in the cortex across brain areas, and hence demonstrate the need for customized optimization, using a three-dimensional finite element model (FEM). A considerable difference was noted in E-field values and distribution at different brain areas. We observed that the volume of activated cortex varied from 3000 to 7000 mm3 between the selected nine clinically relevant coil locations. Coil orientation also changed the induced E-field by a maximum of 10%, and we noted the least optimal values at the standard coil orientation pointing to the nose. The volume of gray matter activated varied by 10% on average between stimulation sites in homologous brain areas in the two hemispheres of the brain. This FEM simulation model clearly demonstrates the importance of TMS parameters for optimal results in clinically relevant brain areas. The results show that TMS parameters cannot be interchangeably used between individuals, hemispheres, and brain areas. The focality of the TMS induced E-field along with its optimal magnitude should be considered as critical TMS parameters that should be individually optimized.

scholarly journals Three-Dimensional Casson Nanofluid Thin Film Flow over an Inclined Rotating Disk with the Impact of Heat Generation/Consumption and Thermal Radiation

Coatings ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 248 ◽  
Author(s):  
Anwar Saeed ◽  
Zahir Shah ◽  
Saeed Islam ◽  
Muhammad Jawad ◽  
Asad Ullah ◽  
...  
Keyword(s):  
Thin Film ◽  
Boundary Layer ◽  
Differential Equations ◽  
Thermal Boundary Layer ◽  
Energy Transport ◽  
Film Flow ◽  
Three Dimensional ◽  
Concentration Profiles ◽  
Thin Film Flow ◽  
The Impact

In this research, the three-dimensional nanofluid thin-film flow of Casson fluid over an inclined steady rotating plane is examined. A thermal radiated nanofluid thin film flow is considered with suction/injection effects. With the help of similarity variables, the partial differential equations (PDEs) are converted into a system of ordinary differential equations (ODEs). The obtained ODEs are solved by the homotopy analysis method (HAM) with the association of MATHEMATICA software. The boundary-layer over an inclined steady rotating plane is plotted and explored in detail for the velocity, temperature, and concentration profiles. Also, the surface rate of heat transfer and shear stress are described in detail. The impact of numerous embedded parameters, such as the Schmidt number, Brownian motion parameter, thermophoretic parameter, and Casson parameter (Sc, Nb, Nt, γ), etc., were examined on the velocity, temperature, and concentration profiles, respectively. The essential terms of the Nusselt number and Sherwood number were also examined numerically and physically for the temperature and concentration profiles. It was observed that the radiation source improves the energy transport to enhance the flow motion. The smaller values of the Prandtl number, Pr, augmented the thermal boundary-layer and decreased the flow field. The increasing values of the rotation parameter decreased the thermal boundary layer thickness. These outputs are examined physically and numerically and are also discussed.

Numerical Simulation of Inclined Multi-Seam Mining Subsidence of Considered the Impact by Faults

2011 ◽  
Vol 250-253 ◽  
pp. 2135-2140
Author(s):  
Zhi Ping Wu ◽  
Sheng Hua Qiu ◽  
Ying Li
Keyword(s):  
Working Conditions ◽  
Three Dimensional ◽  
Surface Subsidence ◽  
Differential Settlement ◽  
Geological Condition ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Seam Mining ◽  
The Impact ◽  
Roof Strata

According to the complex mining geological condition of Shandong gentle inclined multi-seam mining, Use the three-dimensional finite element numerical analysis software to establish three-dimensional geological model under the different mining working conditions. Taking into account the impact of faults to calculate multi-seam roof strata movement and surface subsidence caused by the different mining working conditions. The level displacement & subsidence distribution curve of the reference point of surface & multi-seam roof strata under the different working conditions is shown. The maximum, minimum settlement, differential settlement and subsidence diagram is shown. And the principal stress, shear stress value of surface & multi-seam roof strata after mining also is shown. The results showed that: little change of the biggest surface subsidence and differential settlement is caused by mining 3101&3102 face or separate 3101 or 3102 face. And the largest subsidence, and the settlement difference of the surface is 520mm, 498mm, 515mm and 59mm, 78mm, 81mm, Respectively. It provides an reference for reasonable, safe, economic for the inclined multi-seam mining under similar conditions.

Prediction of the yielding behaviour of ductile porous materials through computational homogenization

2018 ◽  
Vol 35 (2) ◽  
pp. 604-621
Author(s):  
Rodrigo Pinto Carvalho ◽  
Igor A. Rodrigues Lopes ◽  
Francisco M. Andrade Pires
Keyword(s):  
Three Dimensional ◽  
Yield Locus ◽  
Analytical Models ◽  
Finite Element Models ◽  
Content Type ◽  
Ductile Materials ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Void Geometry ◽  
The Impact

Purpose The purpose of this paper is to predict the yield locus of porous ductile materials, evaluate the impact of void geometry and compare the computational results with existing analytical models. Design/methodology/approach A computational homogenization strategy for the definition of the elasto-plastic transition is proposed. Representative volume elements (RVEs) containing single-centred ellipsoidal voids are analysed using three-dimensional finite element models under the geometrically non-linear hypothesis of finite strains. Yield curves are obtained by means of systematic analysis of RVEs considering different kinematical models: linear boundary displacements (upper bound), boundary displacement fluctuation periodicity and uniform boundary traction (lower bound). Findings The influence of void geometry is captured and the reduction in the material strength is observed. Analytical models usually overestimate the impact of void geometry on the yield locus. Originality/value This paper proposes an alternative criterion for porous ductile materials and assesses the accuracy of analytical models through the simulation of three-dimensional finite element models under geometrically non-linear hypothesis.

Optimization of the Engine Hood to Reduce the Head Injury during the Vehicle-Human Collision

2012 ◽  
Vol 192 ◽  
pp. 29-36
Author(s):  
Yu Xin Wang ◽  
Qing Chun Wang ◽  
Jian Rong Fu ◽  
Hong Hai Qiao
Keyword(s):  
Finite Element ◽  
Head Injury ◽  
Optimization Design ◽  
Three Dimensional ◽  
Element Model ◽  
Head Model ◽  
Modeling Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
The Impact

Effect of hard point of the engine hood on the head injury during the vehicle-human collision was studied to improve the design of engine hood. Firstly, the current common model of the engine hood was established with three-dimensional finite element modeling software, and 20 areas were divided, also a standard head finite element model was imported, secondly, each area of the engine hood was clashed by the standard head model, then the impact on the head injure was analyzed and the hard point of the hood area was achieved, thirdly, the optimization of the inside and outside panel materials and the plate structure were carried out to reduce the head damage. The simulation results show that the engine hood after optimization gave less damage to the head, which means the research carried out here is of a good reference to the engine hood optimization design for human protection

scholarly journals Drop Simulation of 6M Drum With Locking-Ring Closure and Liquid Contents

2006 ◽  
Author(s):  
Tsu-Te Wu
Keyword(s):  
Impact Load ◽  
Three Dimensional ◽  
Structural Response ◽  
Material Model ◽  
Element Model ◽  
Ring Closure ◽  
Foot Drop ◽  
Torque Load ◽  
Three Dimensional Finite Element ◽  
The Impact

This paper presents the dynamic simulation of the 6M drum with a locking-ring type closure subjected to a 4.9-foot drop. The drum is filled with water to 98 percent of overflow capacity. A three dimensional finite-element model consisting of metallic, liquid and rubber gasket components is used in the simulation. The water is represented by a hydrodynamic material model in which the material’s volume strength is determined by an equation of state. The explicit numerical method based on the theory of wave propagation is used to determine the combined structural response to the torque load for tightening the locking-ring closure and to the impact load due to the drop.

Fire Durations of Concern for a Modern Legal Weight Truck Cask

2006 ◽  
Author(s):  
Neelima Mallidi ◽  
Miles Greiner ◽  
Venkata V. R. Venigalla
Keyword(s):  
Thermal Protection ◽  
Three Dimensional ◽  
Time History ◽  
Element Analysis ◽  
Pressurized Water ◽  
Dimensional Finite Element ◽  
Term Creep ◽  
Three Dimensional Finite Element ◽  
The Impact ◽  
Containment Integrity

The response of a truck package designed to transport four pressurized water reactor fuel assemblies to a simplified radiation fire model is simulated for a range of fire durations using three-dimensional finite element analysis. A model is developed to determine the cumulative seal degradation from its temperature versus time history. This model is used to determine the minimum fire duration that causes the seal to lose containment integrity. The fire durations that cause the maximum cladding temperature to reach its long term creep deformation and burst rupture temperatures are determined and found to be longer than the duration that cause the seal to lose containment integrity. These simulations are repeated for package models without the compliant regions of the impact limiters, and for a package with the impact limiter completely removed. These simulations quantify the level of thermal protection the impact limiters provide to the seals and cladding during simulated fires.

Sign in / Sign up

Export Citation Format

Share Document