scholarly journals A Combination of a Vibrational Electromagnetic Energy Harvester and a Giant Magnetoimpedance (GMI) Sensor

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 1873
Author(s):  
Juan Jesús Beato-López ◽  
Isaac Royo-Silvestre ◽  
José María Algueta-Miguel ◽  
Cristina Gómez-Polo
Keyword(s):  
Permanent Magnets ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Magnetic Levitation ◽  
Low Cost ◽  
Mechanical Vibration ◽  
Inertial Mass ◽  
Amorphous Wire ◽  
Magnetic Element ◽  
Giant Magnetoimpedance

An energy harvesting device combined with a giant magnetoimpedance (GMI) sensor is presented to analyze low frequency vibrating systems. An electromagnetic harvester based on magnetic levitation is proposed for the electric power generation. The device is composed of two fixed permanent magnets at both ends of a cylindrical frame, a levitating magnet acting as inertial mass and a pick-up coil to collect the induced electromotive force. At the resonance frequency (10 Hz) a maximum electrical power of 1.4 mW at 0.5 g is generated. Moreover, an amorphous wire was employed as sensor nucleus for the design of a linear accelerometer prototype. The sensor is based on the GMI effect where the impedance changes occur as a consequence of the variations of the effective magnetic field due to an oscillating magnetic element. As a result of the magnet’s periodic motion, an amplitude modulated signal (AM) was obtained, its amplitude being proportional to mechanical vibration amplitude (or acceleration). The sensor’s response was examined for a simple ferrite magnet under vibration and compared with that obtained for the vibrational energy harvester. As a result of the small amplitudes of vibration, a linear sensor response was obtained that could be employed in the design of low cost and simple accelerometers.

MAGNETIC LEVITATION AS ENERGY HARVESTER

2021 ◽  
pp. 51-53
Author(s):  
Piyusha S. Shetgar ◽  
A.V. Thalange ◽  
Zaid H. Shaikh ◽  
Tehrim J. Ustad
Keyword(s):  
Free Energy ◽  
Energy Harvester ◽  
Theoretical Study ◽  
Magnetic Levitation ◽  
Low Cost ◽  
Electrical Power ◽  
Magnetic Element ◽  
Mechanical Part ◽  
Wear And Tear ◽  
Harvesting Systems

Magnetic levitation as energy harvester has been widely studied since past few years. It can be used to implement a low-cost and maintenance-free energy harvester. For self-powering a broad range of technologies for long periods of time, levitation-based harvesting systems able to operate autonomously. In this paper, a theoretical study is presented of a harvester conguration that utilizes the motion of a levitated hard-magnetic element to generate electrical power. The levitation used minimizes the loss caused due to wear and tear of mechanical part thus increasing the life of the system.

scholarly journals Design of a 3-RPR Flexure System for Optical Switch Assembly

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Guiyue Kou ◽  
Mouyou Lin ◽  
Changbao Chu
Keyword(s):  
Permanent Magnets ◽  
Optical Switch ◽  
Low Cost ◽  
Mechanical Vibration ◽  
Analytical Models ◽  
Assembly System ◽  
Sensors And Actuators ◽  
Damping Force ◽  
Element Analysis ◽  
Compact Size

In the MEMS optical switch assembly, the collision is likely to happen between the optical fiber and the U-groove of the chip due to the uncontrollable assembly errors. However, these errors can hardly be completely eliminated by the active control using high precision sensors and actuators. It will cause the large acting force and part damage, which further leads to the assembly failure. To solve this question, this paper presents a novel low-cost three-degree-of-freedom (three-DOF) passive flexure system to adaptively eliminate the planar assembly errors. The flexure system adopts three parallel kinematic chains with a novel 3-RPR structure and has a compact size with a diameter of 125 mm and thickness of 12 mm. A novel eddy current damper with the structure of Halbach array permanent magnets (PMs) is utilized to suppress the adverse mechanical vibration of the assembly system from the background disturbances. Analytical models are established to analyze the kinematic, static, and dynamic performances of the system in detail. Finally, finite element analysis is adopted to verify the established models for optimum design. The flexure system can generate a large deformation of 1.02 mm along the two translational directions and 0.02° along the rotational direction below the yield state of the material, and it has much higher natural frequencies than 200 Hz. Moreover, the large damping force means that the designed ECD can suppress the system vibration quickly. The above results indicate the excellent characteristics of the assembly system that will be applied into the optical switch assembly.

Performance Evaluation of Magnetohydrodynamic Bearing

2005 ◽  
Author(s):  
H. Hirani ◽  
P. Samanta
Keyword(s):  
High Speed ◽  
Permanent Magnets ◽  
Magnetic Levitation ◽  
Hydrodynamic Lubrication ◽  
Low Cost ◽  
Low Friction ◽  
Oil Flow ◽  
Hybrid Bearing ◽  
Commercial Applications ◽  
Structural Simplicity

The present paper introduces a concept of hydrodynamic-permanent-magnetic hybrid bearing. The hybrid bearing uses repulsive force between permanent magnets and fluid force developed due to relative speed in a single assembly arrangement. Repulsive type passive magnetic levitation has advantage of minimum starting torque. Hydrodynamic lubrication mechanism has advantage of low friction at medium and high speed. This hybridization will be an attractive choice in commercial applications for its low cost, structural-simplicity and no metal-to-metal contact. An experimental setup is designed and developed to investigate the performance characteristics of proposed concept of hybrid bearing. Minimum film thickness, oil flow rate, and temperature rise are recorded at various speed- and load- conditions. Results are plotted to demonstrate the behavior of hybrid bearing arrangement.

Investigations of a Stiffness Tunable Nonlinear Vibrational Energy Harvester

2014 ◽  
Vol 14 (08) ◽  
pp. 1440023 ◽  
Author(s):  
Dongxu Su ◽  
Kimihiko Nakano ◽  
Rencheng Zheng ◽  
Matthew P. Cartmell
Keyword(s):  
Energy Harvesting ◽  
Permanent Magnets ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Duffing Oscillator ◽  
Experimental Tests ◽  
High Energy ◽  
Practical Implementation ◽  
Energy Harvesting Devices ◽  
Energy Orbit

The recent potential benefit of nonlinearity has been applying in order to improve the effectiveness of energy harvesting devices. For instance, at relatively high excitation levels, both low and high-energy responses can coexist for the same parameter combinations in a hardening type Duffing oscillator, and this provides a wider bandwidth and a higher energy harvesting effectiveness under periodic excitations. However, frequency or amplitude sweeps of the excitation must be used in order to reach a desirable high-energy orbit, and this gives a limitation on practical implementation. This paper presents a stiffness tunable nonlinear vibrational energy harvester which contains a moving magnetic end mass attached to a cantilever beam, whose nonlinearity emerges from the interaction forces with two neighboring permanent magnets facing with opposing poles. The motivating hypothesis has been that the jump from the low-energy orbit to the high-energy orbit can be triggered by tuning the stiffness of the system without changing the frequency or the amplitude of the excitation. Theoretical investigations show a methodology for tuning stiffness, and experimental tests have validated that the proposed method can be used to trigger a jump to the desirable state, and hereby this can broaden the bandwidth of the energy harvester.

scholarly journals A new concept of modular magnetic levitation train for urban transport

2018 ◽  
Vol 4 (2) ◽  
pp. 107-119
Author(s):  
Maurizio Cavagnaro ◽  
Vincenzo Delle Site
Keyword(s):  
Permanent Magnets ◽  
Magnetic Levitation ◽  
Low Cost ◽  
National Research Council ◽  
Synchronous Motor ◽  
Urban Transport ◽  
Guidance System ◽  
Design Data ◽  
Linear Synchronous Motor ◽  
Repulsive Forces

Aim: The aim of our project is to solve all technological and functional problems related to the development of the suspended urban Maglev, while maintaining the requirement of simplicity and low cost of construction, operation and maintenance. Both the infrastructure and the vehicle are designed to be industrially produced and assembled on site. Methods of the studies: Our study is based on the theoretical and experimental results obtained during a project of the Italian National Research Council, concerning the performances of opposing permanent magnets, the design of the linear synchronous motor and the possible solutions for realizing the guidance system. On the basis of these results the study of the suspended system was carried out. Results: The paper describes the suspended urban Maglev with PM/PM primary suspension (with opposing permanent magnets) and proposes a mechanical guidance system that uses for stabilization the same repulsive forces between permanent magnets. We also propose a new configuration with HTS/PM primary suspension (with high temperature superconductors opposed to permanent magnets), evaluating pros and cons of this solution. Finally we provide design data on the linear synchronous motor suitable for our system. Conclusion: This paper describes our proposal for a suspended urban Maglev using permanent magnets; our interest focuses on the need to further develop industrially feasible solutions, easy to build and manage, in order to propose a system that is also commercially viable and competitive. The identified advantages justify further studies.

scholarly journals Axial-circular magnetic levitation assisted biofabrication and manipulation of cellular structures

2021 ◽  
Author(s):  
Muge Anil-Inevi ◽  
Kerem Delikoyun ◽  
Gulistan Mese ◽  
H. Cumhur Tekin ◽  
Engin Ozcivici
Keyword(s):  
Self Assembly ◽  
Permanent Magnets ◽  
Magnetic Levitation ◽  
Low Cost ◽  
Cell Types ◽  
Tissue Level ◽  
Ion Concentration ◽  
Remote Manipulation ◽  
Magnetic Focusing ◽  
Working Volume

AbstractDiamagnetic levitation is an emerging technology for remote manipulation of cells in cell and tissue level applications. Low-cost magnetic levitation configurations using permanent magnets are commonly composed of a culture chamber physically sandwiched between two block magnets that limit working volume and applicability. This work describes a single ring magnet-based magnetic levitation system to eliminate physical limitations for biofabrication. Developed configuration utilizes sample culture volume for construct size manipulation and long-term maintenance. Furthermore, our configuration enables convenient transfer of liquid or solid phases during the levitation. Prior to biofabrication, we first calibrated the platform for levitation with polymeric beads, considering the single cell density range of viable cells. By taking advantage of magnetic focusing and cellular self-assembly, millimeter-sized 3D structures were formed and maintained in the system allowing easy and on-site intervention in cell culture with an open operational space. We demonstrated that the levitation protocol could be adapted for levitation of various cell types (i.e., stem cell, adipocyte and cancer cell) representing cells of different densities by modifying the paramagnetic ion concentration that could be also reduced by manipulating the density of the medium. This technique allowed the manipulation and merging of separately formed 3D biological units, as well as the hybrid biofabrication with biopolymers. In conclusion, we believe that this platform will serve as an important tool in broad fields such as bottom-up tissue engineering, drug discovery and developmental biology.

Long Range Six Degree-of-Freedom Magnetic Levitation Using Low Cost Sensing and Control

2020 ◽  
Vol 32 (3) ◽  
pp. 683-691
Author(s):  
Peter Berkelman ◽  
Yu-Sheng Lu ◽  
◽  
Keyword(s):  
Motion Tracking ◽  
Permanent Magnets ◽  
Magnetic Levitation ◽  
Low Cost ◽  
Position Sensing ◽  
Levitation System ◽  
Magnetic Levitation System ◽  
And Function ◽  
Six Degree Of Freedom ◽  
And Control

We have developed a magnetic levitation system which uses an array of cylindrical actuation coils and a set of three position sensing photodiode assemblies for controlled levitation of a moving platform of permanent magnets. The novelty of this system is that low cost, standard off-the-shelf commodity hardware and software components are used for position sensing and feedback control, rather than costly motion tracking sensing systems and controllers. The design and function of the system are described and controlled motion in all directions is demonstrated through motion ranges of 30 mm horizontal and 20 mm vertical translation, and 26° of roll and 43° of yaw rotation.

Study and design of dual stator permanent magnet machine with spoke-type configurations using phase-group concentrated-coil windings

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1381-1389
Author(s):  
Dezhi Chen ◽  
Chengwu Diao ◽  
Zhiyu Feng ◽  
Shichong Zhang ◽  
Wenliang Zhao
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnets ◽  
Low Cost ◽  
Dynamic Performance ◽  
Torque Ripple ◽  
Permanent Magnet Machine ◽  
Torque Density ◽  
Phase Group ◽  
High Torque ◽  
Simulation Results

In this paper, a novel dual-stator permanent magnet machine (DsPmSynM) with low cost and high torque density is designed. The winding part of the DsPmSynM adopts phase-group concentrated-coil windings, and the permanent magnets are arranged by spoke-type. Firstly, the winding structure reduces the amount of copper at the end of the winding. Secondly, the electromagnetic torque ripple of DsPmSynM is suppressed by reducing the cogging torque. Furthermore, the dynamic performance of DsPmSynM is studied. Finally, the experimental results are compared with the simulation results.

Simply supported FPEDs connected by springs for broadband energy harvesting

2020 ◽  
Vol 64 (1-4) ◽  
pp. 201-210
Author(s):  
Yoshikazu Tanaka ◽  
Satoru Odake ◽  
Jun Miyake ◽  
Hidemi Mutsuda ◽  
Atanas A. Popov ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Evaluation Method ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Functional Materials ◽  
Vibration Energy ◽  
Theoretical Evaluation ◽  
Vibration Energy Harvester ◽  
Polyvinylidene Difluoride ◽  
Simply Supported

Energy harvesting methods that use functional materials have attracted interest because they can take advantage of an abundant but underutilized energy source. Most vibration energy harvester designs operate most effectively around their resonant frequency. However, in practice, the frequency band for ambient vibrational energy is typically broad. The development of technologies for broadband energy harvesting is therefore desirable. The authors previously proposed an energy harvester, called a flexible piezoelectric device (FPED), that consists of a piezoelectric film (polyvinylidene difluoride) and a soft material, such as silicon rubber or polyethylene terephthalate. The authors also proposed a system based on FPEDs for broadband energy harvesting. The system consisted of cantilevered FPEDs, with each FPED connected via a spring. Simply supported FPEDs also have potential for broadband energy harvesting, and here, a theoretical evaluation method is proposed for such a system. Experiments are conducted to validate the derived model.

A Fluidic Vibrational Energy Harvester for Implantable Medical Device Applications

2017 ◽  
Vol 137 (6) ◽  
pp. 152-158
Author(s):  
Satoshi Inoue ◽  
Takuya Takahashi ◽  
Momoko Kumemura ◽  
Kazunori Ishibashi ◽  
Hiroyuki Fujita ◽  
...  
Keyword(s):  
Medical Device ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Implantable Medical Device ◽  
Device Applications
Sign in / Sign up

Export Citation Format

Share Document