scholarly journals Research on the Potential of Spherical Triboelectric Nanogenerator for Collecting Vibration Energy and Measuring Vibration

Sensors ◽  
2020 ◽  
Vol 20 (4) ◽  
pp. 1063 ◽  
Author(s):  
Chuan Wu ◽  
He Huang ◽  
Rui Li ◽  
Chenxing Fan
Keyword(s):  
Power Generation ◽  
Vibration Frequency ◽  
Output Signal ◽  
Signal Amplitude ◽  
Working Environment ◽  
Vibration Energy ◽  
Triboelectric Nanogenerator ◽  
Maximum Output ◽  
Vibration Source ◽  
Environment Temperature

The traditional downhole drilling vibration measurement methods which use cable or battery as power supplies increase the drilling costs and reduce the drilling efficiency. This paper proposes a spherical triboelectric nanogenerator, which shows the potential to collect the downhole vibration energy and measure the vibration frequency in a self-powered model. The power generation tests show that the output signal amplitude of the spherical triboelectric nanogenerator increases as the vibration frequency increases, and it can reach a maximum output voltage of 70 V, a maximum current of 3.3 × 10−5 A, and a maximum power of 10.9 × 10−9 W at 8 Hz when a 10-ohm resistor is connected. Therefore, if the power generation is stored for a certain period of time when numbers of the spherical triboelectric nanogenerators are connected in parallel, it may provide intermittent power for the low-power downhole measurement instruments. In addition, the sensing tests show that the measurement range is 0 to 8 Hz, the test error is less than 2%, the applicable working environment temperature is below 100 degrees Celsius, and the installation distance between the spherical triboelectric nanogenerator and the vibration source should be less than the critical value of 150 cm because the output signal amplitude is inversely proportional to the distance.

scholarly journals A Self-Powered Basketball Training Sensor Based on Triboelectric Nanogenerator

2021 ◽  
Vol 11 (8) ◽  
pp. 3506
Author(s):  
Zhenyu Zhao ◽  
Chuan Wu ◽  
Qing Zhou
Keyword(s):  
Real Time ◽  
Light Emitting Diode ◽  
High Reliability ◽  
Working Environment ◽  
Triboelectric Nanogenerator ◽  
Target Area ◽  
Maximum Output ◽  
Environment Temperature ◽  
Self Powered ◽  
Led Lights

During the basketball training for beginner children, sensors are needed to count the number of times the basketball hits the target area in a certain period of time to evaluate the training effect. This study proposes a self-powered basketball training sensor, based on a triboelectric nanogenerator. The designed sensor with a rectangular floor shape will output a pulse signal with the same frequency as the basketball impact to achieve the measurement function through the mutual contact of the internal copper (Cu) and polytetrafluoroethylene (PTFE). Test results show that the working frequency of the sensor is 0 to 5 Hz, the working environment temperature should be less than 75 °C, the working environment humidity should be less than 95%, and which has high reliability. Further tests show that the maximum output voltage, current, and power of the sensor can reach about 52 V, 4 uA, and 26.5 uW with a 10 MΩ resistance in series, respectively, and the output power can light up 12 light-emitting diode (LED) lights in real-time. Compared with the traditional statistical method of manual observation, the sensor can automatically count data in a self-powered manner, and also can light up the LED lights in real-time as an indicator of whether the basketball impacts the target area, to remind beginner children in real-time.

Study of the Ambient Vibration Energy Harvesting Based on Piezoelectric Effect

2015 ◽  
Vol 14 (01n02) ◽  
pp. 1460017
Author(s):  
Hongyu Si ◽  
Jinlu Dong ◽  
Lei Chen ◽  
Laizhi Sun ◽  
Xiaodong Zhang ◽  
...  
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Resonant Frequency ◽  
Output Power ◽  
Ambient Vibration ◽  
Vibration Energy ◽  
Vibration Source ◽  
Vibration Energy Harvesting ◽  
Parallel Connection ◽  
Piezoelectric Vibrator

The resonance between piezoelectric vibrator and the vibration source is the key to maximize the ambient vibration energy harvesting by using piezoelectric generator. In this paper, the factors that influence the output power of a single piezoelectric vibrator are analyzed. The effect of geometry size (length, thickness, width of piezoelectric chip and thickness of metal shim) of a single cantilever piezoelectric vibrator to the output power is analyzed and simulated with the help of MATLAB (matrix laboratory). The curves that output power varies with geometry size are obtained when the displacement and load at the free end are constant. Then the paper points out multi-resonant frequency piezoelectric power generation, including cantilever multi-resonant frequency piezoelectric power generation and disc type multi-resonant frequency piezoelectric generation. Multi-resonant frequency of cantilever piezoelectric power generation can be realized by placing different quality mass at the free end, while disc type multi-resonant frequency piezoelectric generation can be realized through series and parallel connection of piezoelectric vibrator.

Signal Characteristic Study and Amplifier Design of Magnetic Senor Based on Proton Zeeman Effect

2014 ◽  
Vol 643 ◽  
pp. 190-195
Author(s):  
Tan Chao ◽  
Chao Su ◽  
Li Fang ◽  
Bing Hua Jiang
Keyword(s):  
Magnetic Field ◽  
Output Signal ◽  
Zeeman Effect ◽  
Signal Amplitude ◽  
Maximum Output ◽  
Band Pass Filter ◽  
Sensor Output ◽  
Pass Filter ◽  
Earth Magnetic Field ◽  
Amplifier Design

The paper analyzes the two kinds magnetic field sensor measuring principle based nuclear Zeeman effect, the signal characteristics are analyzed according to the formula of the sensor output signal, the curve of the sensor maximum output signal VS the earth magnetic field obtained by using the method of combination numerical and experimental. With constant output signal amplitude as a criterion, the amplifier which satisfies the characteristic of the sensor output was designed. To further improve the SNR, program controllable self-tracking band pass filter (PCSTBF) was designed based on the switch capacitor filter and the FFT. The results showed that: the SNR was increased by using the amplifier which contains the PCSTBF, and the bandwidth of the output signal was not reduced.

scholarly journals An Optimized Flutter-Driven Triboelectric Nanogenerator with a Low Cut-In Wind Speed

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 366
Author(s):  
Yang Xia ◽  
Yun Tian ◽  
Lanbin Zhang ◽  
Zhihao Ma ◽  
Huliang Dai ◽  
...  
Keyword(s):  
Power Generation ◽  
Wind Speed ◽  
Energy Harvesting ◽  
Wind Energy ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Vibration Behavior ◽  
Air Speed

We present an optimized flutter-driven triboelectric nanogenerator (TENG) for wind energy harvesting. The vibration and power generation characteristics of this TENG are investigated in detail, and a low cut-in wind speed of 3.4 m/s is achieved. It is found that the air speed, the thickness and length of the membrane, and the distance between the electrode plates mainly determine the PTFE membrane’s vibration behavior and the performance of TENG. With the optimized value of the thickness and length of the membrane and the distance of the electrode plates, the peak open-circuit voltage and output power of TENG reach 297 V and 0.46 mW at a wind speed of 10 m/s. The energy generated by TENG can directly light up dozens of LEDs and keep a digital watch running continuously by charging a capacitor of 100 μF at a wind speed of 8 m/s.

Transmission of Ultrasonic Waves Via Optical Silica Glass Fiber Doped by 7.5% of TiO2 with the Use of Power Sandwich Transducer

2011 ◽  
Vol 36 (1) ◽  
pp. 141-150 ◽  
Author(s):  
Sylwia Muc ◽  
Tadeusz Gudra
Keyword(s):  
Optical Fibre ◽  
Output Signal ◽  
Optical Waveguides ◽  
Experimental Studies ◽  
Signal Amplitude ◽  
Capacitive Sensor ◽  
Ultrasonic Waves ◽  
Sandwich Type ◽  
Type Transducer ◽  
Simultaneous Transmission

Abstract The possibility of acoustic wave propagation in optical waveguides creates new prospects for simultaneous transmission of laser beams and ultrasonic waves. Combined laser-ultrasonic technology could be useful in e.g. surgical treatment. The article presents the results of experimental studies of transmission of ultrasonic wave in optical fibres, the core of which is doped by 7.5% of TiO2, using a sandwich-type transducer. It also presents amplitude characteristics of an ultrasonic signal propagated in the optical fibre. Authors studied the effect which the length of the fibre has on the achieved output signal amplitudes. They presented the relation of the output signal amplitude from a capacitive sensor to the power applied to the sandwich-type transducer. The obtained results were compared with the results produced when using an optical fibre with a core doped by 3% of GeO2, in order to select optical fibre suitable for simultaneous transmission of ultrasonic waves and laser rays.

Ferromagnetic nanoparticle-embedded hybrid nanogenerator for harvesting omnidirectional vibration energy

Nanoscale ◽  
2018 ◽  
Vol 10 (26) ◽  
pp. 12276-12283 ◽  
Author(s):  
Daewon Kim ◽  
Ik Kyeong Jin ◽  
Yang-Kyu Choi
Keyword(s):  
Vibration Energy ◽  
Triboelectric Nanogenerator ◽  
Simple Treatment ◽  
Hybrid Nanogenerator ◽  
Electromagnetic Generator

A ferromagnetic nanoparticle-embedded hybrid nanogenerator (FHNG) which combines triboelectric nanogenerator (TENG) and electromagnetic generator (EMG) was is proposed. Through a simple treatment, high-triboelectric monolayers of nanoscale thicknesses are formed.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Remediation of Mariculture Sediment by Sediment Microbial Fuel Cell

2021 ◽  
Vol 261 ◽  
pp. 04037
Author(s):  
Nannan Zhao
Keyword(s):  
Power Generation ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Ammonia Nitrogen ◽  
Maximum Output ◽  
External Resistance ◽  
Removal Rates ◽  
Marine Aquaculture ◽  
Sediment Microbial Fuel Cell ◽  
Generation Capacity

To investigate the removal effect of pollutants in mariculture sediment by sediment microbial fuel cell (SMFC) and its power generation capacity, the effects of external resistance, cathode pH and cathode dissolved oxygen concentration (DO) on the SMFC system were investigated. The results showed that the optimal parameters for SMFC were as follows: external resistance = 1500 Ω, pH = 8.5 and DO = 5 mg·L-1. In these situations, the power generation performance and organic degradation effect were both the best. The maximum output voltages were 585, 606, and 587 mV, respectively; the removal rates of COD in sediment were 75.51%, 84.21% and 86.63%, respectively; and the removal rates of ammonia nitrogen in sediment were 80.34%, 98.91% and 90.24%, respectively. The SMFC system had a certain degradation ability to pollutants such as COD and ammonia nitrogen in the sediment of the marine aquaculture areas, which had a broad application prospect.

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

Sign in / Sign up

Export Citation Format

Share Document