scholarly journals A Time-of-Flight Range Sensor Using Four-Tap Lock-In Pixels with High near Infrared Sensitivity for LiDAR Applications

Sensors ◽  
2019 ◽  
Vol 20 (1) ◽  
pp. 116 ◽  
Author(s):  
Sanggwon Lee ◽  
Keita Yasutomi ◽  
Masato Morita ◽  
Hodaka Kawanishi ◽  
Shoji Kawahito
Keyword(s):  
High Speed ◽  
Near Infrared ◽  
Short Pulse ◽  
Time Of Flight ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Silicon On Insulator ◽  
Oxide Semiconductor ◽  
Fully Depleted ◽  
High Modulation

In this paper, a back-illuminated (BSI) time-of-flight (TOF) sensor using 0.2 µm silicon-on-insulator (SOI) complementary metal oxide semiconductor (CMOS) technology is developed for long-range laser imaging detection and ranging (LiDAR) application. A 200 µm-thick bulk silicon in the SOI substrate is fully depleted by applying high negative voltage at the backside for higher quantum efficiency (QE) in a near-infrared (NIR) region. The proposed SOI-based four-tap charge modulator achieves a high-speed charge modulation and high modulation contrast of 71% in a NIR region. In addition, in-pixel drain function is used for short-pulse TOF measurements. A distance measurement up to 27 m is carried out with +1.8~−3.0% linearity error and range resolution of 4.5 cm in outdoor conditions. The measured QE of 55% is attained at 940 nm which is suitable for outdoor use due to the reduced spectral components of solar radiation.

A 31 GHz body-biased configurable power amplifier in 28 nm FD-SOI CMOS for 5 G applications

2020 ◽  
pp. 1-18
Author(s):  
Florent Torres ◽  
Eric Kerhervé ◽  
Andreia Cathelin ◽  
Magali De Matos
Keyword(s):  
Power Amplifier ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Silicon On Insulator ◽  
Oxide Semiconductor ◽  
Fully Depleted ◽  
Technology Roadmap ◽  
Wide Range ◽  
28 Nm ◽  
Soi Cmos

Abstract This paper presents a 31 GHz integrated power amplifier (PA) in 28 nm Fully Depleted Silicon-On-Insulator Complementary Metal Oxide Semiconductor (FD-SOI CMOS) technology and targeting SoC implementation for 5 G applications. Fine-grain wide range power control with more than 10 dB tuning range is enabled by body biasing feature while the design improves voltage standing wave ratio (VSWR) robustness, stability and reverse isolation by using optimized 90° hybrid couplers and capacitive neutralization on both stages. Maximum power gain of 32.6 dB, PAEmax of 25.5% and Psat of 17.9 dBm are measured while robustness to industrial temperature range and process spread is demonstrated. Temperature-induced performance variation compensation, as well as amplitude-to-phase modulation (AM-PM) optimization regarding output power back-off, are achieved through body-bias node. This PA exhibits an International Technology Roadmap for Semiconductors figure of merit (ITRS FOM) of 26 925, the highest reported around 30 GHz to authors' knowledge.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

scholarly journals A Back-Illuminated Time-of-Flight Image Sensor with SOI-Based Fully Depleted Detector Technology for LiDAR Application

Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 798 ◽  
Author(s):  
Sanggwon Lee ◽  
Keita Yasutomi ◽  
Ho Hai Nam ◽  
Masato Morita ◽  
Shoji Kawahito
Keyword(s):  
Near Infrared ◽  
Time Of Flight ◽  
Image Sensor ◽  
Light Signal ◽  
Silicon On Insulator ◽  
Light Power ◽  
Fully Depleted ◽  
Range Resolution ◽  
Back Illuminated ◽  
Detector Technology

A back-illuminated time-of-flight (ToF) image sensor based on a 0.2 µm silicon-on-insulator (SOI) CMOS detector technology using fully-depleted substrate is developed for the light detection and ranging (LiDAR) applications. A fully-depleted 200 µm-thick bulk silicon is used for the higher quantum efficiency (QE) in a near-infrared (NIR) region. The developed SOI pixel structure has a 4-tapped charge modulator with a draining function to achieve a higher range resolution and to cancel background light signal. A distance is measured up to 27 m with a range resolution of 12 cm at the outdoor and average light power density is 150 mW/m2@30 m.

scholarly journals A 2.6 GS/s 8-Bit Time-Interleaved SAR ADC in 55 nm CMOS Technology

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 305 ◽  
Author(s):  
Dong Wang ◽  
Xiaoge Zhu ◽  
Xuan Guo ◽  
Jian Luan ◽  
Lei Zhou ◽  
...  
Keyword(s):  
High Speed ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Sar Adc ◽  
Oxide Semiconductor ◽  
Power Measurement ◽  
Cmos Process ◽  
Analog To Digital ◽  
Full Speed ◽  
Time Interleaved

This paper presents an eight-channel time-interleaved (TI) 2.6 GS/s 8-bit successive approximation register (SAR) analog-to-digital converter (ADC) prototype in a 55-nm complementary metal-oxide-semiconductor (CMOS) process. The channel-selection-embedded bootstrap switch is adopted to perform sampling times synchronization using the full-speed master clock to suppress the time skew between channels. Based on the segmented pre-quantization and bypass switching scheme, double alternate comparators clocked asynchronously with background offset calibration are utilized in sub-channel SAR ADC to achieve high speed and low power. Measurement results show that the signal-to-noise-and-distortion ratio (SNDR) of the ADC is above 38.2 dB up to 500 MHz input frequency and above 31.8 dB across the entire first Nyquist zone. The differential non-linearity (DNL) and integral non-linearity (INL) are +0.93/−0.85 LSB and +0.71/−0.91 LSB, respectively. The ADC consumes 60 mW from a 1.2 V supply, occupies an area of 400 μm × 550 μm, and exhibits a figure-of-merit (FoM) of 348 fJ/conversion-step.

A New Technique for Designing Low-Power High-Speed Domino Logic Circuits in FinFET Technology

2019 ◽  
Vol 28 (10) ◽  
pp. 1950165 ◽  
Author(s):  
Sandeep Garg ◽  
Tarun K. Gupta
Keyword(s):  
Low Power ◽  
High Speed ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Power Reduction ◽  
Maximum Power ◽  
Oxide Semiconductor ◽  
Domino Logic ◽  
Maximum Delay

In this paper, a fin field-effect transistor (FinFET)-based domino technique dynamic node-driven feedback transistor domino logic (DNDFTDL) is designed for low-power, high-speed and improved noise performance. In the proposed domino technique, the concept of current division is explored below the evaluation network for enhancement of performance parameters. Simulations are carried out for 32-nm complementary metal–oxide–semiconductor (CMOS) and FinFET node using HSPICE for 2-, 4-, 8- and 16-input OR gates with a DC supply voltage of 0.9[Formula: see text]V. Proposed technique shows a maximum power reduction of 73.93% in FinFET short-gate (SG) mode as compared to conditional stacked keeper domino logic (CSKDL) technique and a maximum power reduction of 72.12% as compared to modified high-speed clocked delay domino logic (M-HSCD) technique in FinFET low-power (LP) mode. The proposed technique shows a maximum delay reduction of 35.52% as compared to voltage comparison domino (VCD) technique in SG mode and a reduction of 25.01% as compared to current mirror footed domino logic (CMFD) technique in LP mode. The unity noise gain (UNG) of the proposed circuit is 1.72–[Formula: see text] higher compared to different existing techniques in FinFET SG mode and is 1.42–[Formula: see text] higher in FinFET LP mode. The Figure of Merit (FOM) of the proposed circuit is up to [Formula: see text] higher as compared to existing domino logic techniques because of lower values of power, delay and area and higher values of UNG of the proposed circuit. In addition, the proposed technique shows a maximum power reduction of up to 68.64% in FinFET technology as compared to its counterpart in CMOS technology.

scholarly journals High-speed programmable photonic circuits in a cryogenically compatible, visible–near-infrared 200 mm CMOS architecture

2021 ◽  
Author(s):  
Mark Dong ◽  
Genevieve Clark ◽  
Andrew J. Leenheer ◽  
Matthew Zimmermann ◽  
Daniel Dominguez ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Power Consumption ◽  
High Speed ◽  
Large Scale ◽  
Near Infrared ◽  
Response Times ◽  
Photonic Integrated Circuits ◽  
Complementary Metal Oxide Semiconductor ◽  
Phase Shifters ◽  
Oxide Semiconductor

AbstractRecent advances in photonic integrated circuits have enabled a new generation of programmable Mach–Zehnder meshes (MZMs) realized by using cascaded Mach–Zehnder interferometers capable of universal linear-optical transformations on N input/output optical modes. MZMs serve critical functions in photonic quantum information processing, quantum-enhanced sensor networks, machine learning and other applications. However, MZM implementations reported to date rely on thermo-optic phase shifters, which limit applications due to slow response times and high power consumption. Here we introduce a large-scale MZM platform made in a 200 mm complementary metal–oxide–semiconductor foundry, which uses aluminium nitride piezo-optomechanical actuators coupled to silicon nitride waveguides, enabling low-loss propagation with phase modulation at greater than 100 MHz in the visible–near-infrared wavelengths. Moreover, the vanishingly low hold-power consumption of the piezo-actuators enables these photonic integrated circuits to operate at cryogenic temperatures, paving the way for a fully integrated device architecture for a range of quantum applications.

A novel design of nano router with high-speed crossbar scheduler for digital systems in QCA paradigm

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Kalpana Kasilingam ◽  
Paulchamy Balaiah
Keyword(s):  
High Speed ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Modern Technology ◽  
Oxide Semiconductor ◽  
Large Area ◽  
Content Type ◽  
Compact Size ◽  
High Power Consumption ◽  
High Speed Data

Purpose The nano-router would be a mastery device for providing high-speed data delivery. Here nano-router with a space-efficient crossbar scheduler is used for making absolutely less consumption in power. Design/methodology/approach In the emerging modern technology, every one of us is expecting a delivery of data at a high speed. To achieve high-speed delivery the authors are using the router. The router used here is at nanoscale reading which provides a compact size. Findings This can be implemented using the modern tools called Quantum-dot Cellular Automata (QCA) which is operated without the use of a transistor. As conventional complementary metal oxide semiconductor (CMOS) designs have some limitations such as low density, high power consumption and requirement of a large area. Research limitations/implications To overcome these limitations the QCA is used. It characterizes capability is used to substituting CMOS technology. The round-robin fashion is used in a high-speed space-efficient crossbar scheduler. Practical implications The simulation of the planned circuit with notional information established the practical identity of the scheme. Social implications The proposed nano router can be stimulated in the QCA environment using the QCADesigner tool and the power of the router can be calculated with the QCADesigner–E tool. Originality/value The proposed nano router can be stimulated in the QCA environment using the QCADesigner tool and the power of the router can be calculated with the QCADesigner–E tool. In this work, the performance of the router can be done in both the QCA environment and CMOS technology.

Sign in / Sign up

Export Citation Format

Share Document