scholarly journals Distributed Fiberoptic Sensor for Simultaneous Humidity and Temperature Monitoring Based on Polyimide-Coated Optical Fibers

Sensors ◽  
2019 ◽  
Vol 19 (23) ◽  
pp. 5279 ◽  
Author(s):  
Pavol Stajanca ◽  
Konstantin Hicke ◽  
Katerina Krebber
Keyword(s):  
Optical Fibers ◽  
Temperature Response ◽  
Strong Temperature Dependence ◽  
Coated Fiber ◽  
Humidity Response ◽  
Sensing Applications ◽  
First Time ◽  
Humidity Monitoring ◽  
Fiberoptic Sensor

Along temperature, humidity is one of the principal environmental factors that plays an important role in various application areas. Presented work investigates possibility of distributed fiberoptic humidity monitoring based on humidity-induced strain measurement in polyimide (PI)-coated optical fibers. Characterization of relative humidity (RH) and temperature response of four different commercial PI- and one acrylate-coated fiber was performed using optical backscattering reflectometry (OBR). The study addresses issues of temperature-humidity cross-sensitivity, fiber response stability, repeatability, and the influence of annealing. Acrylate-coated fiber exhibited rather unfavorable nonlinear RH response with strong temperature dependence, which makes it unsuitable for humidity sensing applications. On the other hand, humidity response of PI-coated fibers showed good linearity with fiber sensitivity slightly decreasing at rising temperatures. In the tested range, temperature sensitivity of the fibers remained humidity independent. Thermal annealing was shown to considerably improve and stabilize fiber RH response. Based on performed analysis, a 20 m sensor using the optimal PI-coated fibers was proposed and constructed. The sensor uses dual sensing fiber configuration for mutual decoupling and simultaneous measurement of temperature and RH variations. Using OBR, distributed dual temperature-RH monitoring with cm spatial resolution was demonstrated for the first time.

scholarly journals Characterization of Flexible Copolymer Optical Fibers for Force Sensing Applications

Sensors ◽  
2013 ◽  
Vol 13 (9) ◽  
pp. 11956-11968 ◽  
Author(s):  
Marek Krehel ◽  
René Rossi ◽  
Gian-Luca Bona ◽  
Lukas Scherer
Keyword(s):  
Optical Fibers ◽  
Force Sensing ◽  
Sensing Applications

Characterization of Graphene Oxide Coatings onto Optical Fibers for Sensing Applications

2015 ◽  
Vol 2 (1) ◽  
pp. 171-177 ◽  
Author(s):  
Nélia Alberto ◽  
César Vigário ◽  
Daniel Duarte ◽  
Nuno A.F. Almeida ◽  
Gil Gonçalves ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Optical Fibers ◽  
Oxide Coatings ◽  
Sensing Applications

scholarly journals Fabrication and Characterization of Er/Yb Co-Doped Fluorophosphosilicate Glass Core Optical Fibers

Fibers ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 15
Author(s):  
Denis S. Lipatov ◽  
Alexey S. Lobanov ◽  
Alexey N. Guryanov ◽  
Andrey A. Umnikov ◽  
Alexey N. Abramov ◽  
...  
Keyword(s):  
Optical Fibers ◽  
Chemical Vapor ◽  
Single Mode ◽  
Lasing Efficiency ◽  
Core Diameter ◽  
Manufacturing Method ◽  
Mode Area ◽  
First Time ◽  
Co Doped

The technical process of the synthesis of a fluorophosphosilicate (FPS) glass core was thoroughly investigated for the first time utilizing a modified chemical vapor deposition (MCVD) all-gas-phase fabrication method. It was discovered that the limiting doping level of the silica glass simultaneously co-doped with phosphorus (P) and fluorine (F) was found to be confined by the formation of POF3 gas. The dopants content was achieved as high as 4.7 at% of P and 1.1 at% of F in a glass core, respectively. A developed “in-house” manufacturing method makes it possible to fabricate a large mode area (LMA) purely single-mode Er–Yb co-doped optical fibers with a core diameter of 20 μm and with a lasing efficiency comparable to commercially available LMA Er–Yb optical fibers.

scholarly journals Temperature Sensor Based on Periodically Tapered Optical Fibers

Sensors ◽  
2021 ◽  
Vol 21 (24) ◽  
pp. 8358
Author(s):  
Bartlomiej Guzowski ◽  
Mateusz Łakomski
Keyword(s):  
Linear Function ◽  
Optical Fibers ◽  
Spectral Range ◽  
Temperature Sensor ◽  
Simple Structure ◽  
Free Spectral Range ◽  
Temperature Response ◽  
Temperature Range ◽  
Fabrication And Characterization

In this paper, the fabrication and characterization of a temperature sensor based on periodically tapered optical fibers (PTOF) are presented. The relation between the geometry of the sensors and sensing ability was investigated in order to find the relatively simple structure of a sensor. Four types of PTOF structures with two, four, six and eight waists were manufactured with the fusion splicer. For each PTOF type, the theoretical free spectral range (FSR) was calculated and compared with measurements. The experiments were conducted for a temperature range of 20–70 °C. The results proved that the number of the tapered regions in PTOF is crucial, because some of the investigated structures did not exhibit the temperature response. The interference occurring inside the structures with two and four waists was found be too weak and, therefore, the transmission dip was hardly visible. We proved that sensors with a low number of tapered regions cannot be considered as a temperature sensor. Sufficiently more valuable results were obtained for the last two types of PTOF, where the sensor’s sensitivity was equal to 0.07 dB/°C with an excellent linear fitting (R2 > 0.99). The transmission dip shift can be described by a linear function (R2 > 0.97) with a slope α > 0.39 nm/°C.

TBE in Sweden

2020 ◽  
Keyword(s):  
Genetic Characterization ◽  
Immunoglobulin M ◽  
Enzyme Linked Immunosorbent Assay ◽  
Second Phase ◽  
Serum Samples ◽  
Tick Borne Encephalitis ◽  
Specific Immunoglobulin ◽  
Tick Borne Encephalitis Virus ◽  
First Time

Tick-borne encephalitis virus (TBEV) was isolated for the first time in Sweden in 1958 (from ticks and from 1 tick-borne encephalitis [TBE] patient).1 In 2003, Haglund and colleagues reported the isolation and antigenic and genetic characterization of 14 TBEV strains from Swedish patients (samples collected 1991–1994).2 The first serum sample, from which TBEV was isolated, was obtained 2–10 days after onset of disease and found to be negative for anti-TBEV immunoglobulin M (IgM) by enzyme-linked immunosorbent assay (ELISA), whereas TBEV-specific IgM (and TBEV-specific immunoglobulin G/cerebrospinal fluid [IgG/CSF] activity) was demonstrated in later serum samples taken during the second phase of the disease.

Chemical Constituents and Antibacterial Activity of Cissus Aralioides.

2020 ◽  
Vol 17 ◽  
Author(s):  
Balogun Olaoye Solomon ◽  
Ajayi Olukayode Solomon ◽  
Owolabi Temitayo Abidemi ◽  
Oladimeji Abdulkarbir Oladele ◽  
Liu Zhiqiang
Keyword(s):  
Plant Extract ◽  
Chemical Constituents ◽  
Ethyl Acetate Fraction ◽  
Antibacterial Activities ◽  
Sub Saharan Africa ◽  
Chromatographic Purification ◽  
Whole Plant ◽  
Sub Saharan ◽  
First Time

: Cissus aralioides is a medicinal plant used in sub-Saharan Africa for treatment of infectious diseases; however the chemical constituents of the plant have not been investigated. Thus, in this study, attempt was made at identifying predominant phytochemical constituents of the plant through chromatographic purification and silylation of the plant extract, and subsequent characterization using spectroscopic and GC-MS techniques. The minimum inhibitory concentration (MICs) for the antibacterial activities of the plant extract, chromatographic fractions and isolated compounds were also examined. Chromatographic purification of the ethyl acetate fraction from the whole plant afforded three compounds: β-sitosterol (1), stigmasterol (2) and friedelin (3). The phytosterols (1 and 2) were obtained together as a mixture. The GC-MS analysis of silylated extract indicated alcohols, fatty acids and sugars as predominant classes, with composition of 24.62, 36.90 and 26.52% respectively. Results of MICs indicated that friedelin and other chromatographic fractions had values (0.0626-1.0 mg/mL) comparable with the standard antibiotics used. Characterization of natural products from C. aralioides is being reported for the first time in this study.

Green Synthesis and Spectroscopic Studies of Ag-rGO Nanocomposites for Highly Selective Mercury (II) Sensing

2018 ◽  
Vol 9 (1) ◽  
pp. 101-108 ◽  
Author(s):  
Shubhangi J. Mane-Gavade ◽  
Sandip R. Sabale ◽  
Xiao-Ying Yu ◽  
Gurunath H. Nikam ◽  
Bhaskar V. Tamhankar
Keyword(s):  
Green Synthesis ◽  
Color Change ◽  
Limit Of Detection ◽  
Aqueous Media ◽  
Suitable Condition ◽  
Cost Effective ◽  
Spectroscopic Studies ◽  
Calibration Plot ◽  
First Time

Introduction: Herein we report the green synthesis and characterization of silverreduced graphene oxide nanocomposites (Ag-rGO) using Acacia nilotica gum for the first time. Experimental: We demonstrate the Hg2+ ions sensing ability of the Ag-rGO nanocomposites form aqueous medium. The developed colorimetric sensor method is simple, fast and selective for the detection of Hg2+ ions in aqueous media in presence of other associated ions. A significant color change was noticed with naked eye upon Hg2+ addition. The color change was not observed for cations including Sr2+, Ni2+, Cd2+, Pb2+, Mg2+, Ca2+, Fe2+, Ba2+ and Mn2+indicating that only Hg2+ shows a strong interaction with Ag-rGO nanocomposites. Under the most suitable condition, the calibration plot (A0-A) against concentration of Hg2+ was linear in the range of 0.1-1.0 ppm with a correlation coefficient (R2) value 0.9998. Results & Conclusion The concentration of Hg2+ was quantitatively determined with the Limit of Detection (LOD) of 0.85 ppm. Also, this method shows excellent selectivity towards Hg2+ over nine other cations tested. Moreover, the method offers a new cost effective, rapid and simple approach for the detection of Hg2+ in water samples.

scholarly journals Waste-Based One-Part Alkali Activated Materials

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2911
Author(s):  
Margarida Gonçalves ◽  
Inês Silveirinha Vilarinho ◽  
Marinélia Capela ◽  
Ana Caetano ◽  
Rui Miguel Novais ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Microstructural Analysis ◽  
Construction Materials ◽  
Sodium Metasilicate ◽  
High Compressive Strength ◽  
Hardened State ◽  
First Time ◽  
Furnace Slag ◽  
Alkali Activated

Ordinary Portland Cement is the most widely used binder in the construction sector; however, a very high carbon footprint is associated with its production process. Consequently, more sustainable alternative construction materials are being investigated, namely, one-part alkali activated materials (AAMs). In this work, waste-based one-part AAMs binders were developed using only a blast furnace slag, as the solid precursor, and sodium metasilicate, as the solid activator. For the first time, mortars in which the commercial sand was replaced by two exhausted sands from biomass boilers (CA and CT) were developed. Firstly, the characterization of the slag and sands (aggregates) was performed. After, the AAMs fresh and hardened state properties were evaluated, being the characterization complemented by FTIR and microstructural analysis. The binder and the mortars prepared with commercial sand presented high compressive strength values after 28 days of curing-56 MPa and 79 MPa, respectively. The mortars developed with exhausted sands exhibit outstanding compressive strength values, 86 and 70 MPa for CT and CA, respectively, and the other material’s properties were not affected. Consequently, this work proved that high compressive strength waste-based one-part AAMs mortars can be produced and that it is feasible to use another waste as aggregate in the mortar’s formulations: the exhausted sands from biomass boilers.

Sign in / Sign up

Export Citation Format

Share Document