scholarly journals Analysis of Graphene Antenna Properties for 5G Applications

Sensors ◽  
2019 ◽  
Vol 19 (22) ◽  
pp. 4835 ◽  
Author(s):  
Siti Nor Hafizah Sa’don ◽  
Mohd Haizal Jamaluddin ◽  
Muhammad Ramlee Kamarudin ◽  
Fauzan Ahmad ◽  
Yoshihide Yamada ◽  
...  
Keyword(s):  
Screen Printing ◽  
Coplanar Waveguide ◽  
Beam Width ◽  
High Gain ◽  
Array Element ◽  
Impedance Bandwidth ◽  
Single Element ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Large Bandwidth

The incoming 5G technology requires antennas with a greater capacity, wider wireless spectrum utilisation, high gain, and steer-ability. This is due to the cramped spectrum utilisation in the previous generation. As a matter of fact, conventional antennas are unable to serve the new frequency due to the limitations in fabrication and installation mainly for smaller sizes. The use of graphene material promises antennas with smaller sizes and thinner dimensions, yet capable of emitting higher frequencies. Hence, graphene antennas were studied at a frequency of 15 GHz in both single and array elements. The high-frequency antenna contributed to a large bandwidth and was excited by coplanar waveguide for easy fabrication on one surface via screen printing. The defected ground structure was applied in an array element to improve the radiation and increase the gain. The results showed that the printed, single element graphene antenna produced an impedance bandwidth, gain, and efficiency of 48.64%, 2.87 dBi, and 67.44%, respectively. Meanwhile, the array element produced slightly better efficiency (72.98%), approximately the same impedance bandwidth as the single element (48.98%), but higher gain (8.41 dBi). Moreover, it provided a beam width of 21.2° with scanning beam capability from 0° up to 39.05°. Thus, it was proved that graphene materials can be applied in 5G.

scholarly journals A Novel High Gain Monopole Antenna Array for 60 GHz Millimeter-Wave Communications

2020 ◽  
Vol 10 (13) ◽  
pp. 4546
Author(s):  
Tarek S. Mneesy ◽  
Radwa K. Hamad ◽  
Amira I. Zaki ◽  
Wael A. E. Ali
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Ground Plane ◽  
High Gain ◽  
Monopole Antenna ◽  
Impedance Bandwidth ◽  
Single Element ◽  
60 Ghz ◽  
Defected Ground Structure ◽  
Element Array

This paper presented the design and implementation of a 60 GHz single element monopole antenna as well as a two-element array made of two 60 GHz monopole antennas. The proposed antenna array was used for 5G applications with radiation characteristics that conformed to the requirements of wireless communication systems. The proposed single element was designed and optimized to work at 60 GHz with a bandwidth of 6.6 GHz (57.2–63.8 GHz) and a maximum gain of 11.6 dB. The design was optimized by double T-shaped structures that were added in the rectangular slots, as well as two external stubs in order to achieve a highly directed radiation pattern. Moreover, ring and circular slots were made in the partial ground plane at an optimized distance as a defected ground structure (DGS) to improve the impedance bandwidth in the desired band. The two-element array was fed by a feed network, thus improving both the impedance bandwidth and gain. The single element and array were fabricated, and the measured and simulated results mimicked each other in both return loss and antenna gain.

Gain enhancement over a wideband in CPW-fed compact circular patch antenna

2013 ◽  
Vol 6 (5) ◽  
pp. 497-503 ◽  
Author(s):  
Kirti Vyas ◽  
Garima Sanyal ◽  
Arun Kumar Sharma ◽  
Pramod Kumar Singhal
Keyword(s):  
Patch Antenna ◽  
Coplanar Waveguide ◽  
Impedance Bandwidth ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Radiation Characteristics ◽  
Circular Patch ◽  
Gain Enhancement ◽  
X Band ◽  
Circular Patch Antenna

The present paper reports the gain enhancement over a wideband (12–15 GHz) in a coplanar waveguide (CPW)-fed circular patch antenna with circular defected ground structure (DGS). Two compact coplanar circular antennas have been designed and fabricated with and without DGS of same volume 18 × 20 × 1.6 mm3, built over FR4-epoxy substrate (εr = 4.4). Gain enhancement has been achieved by optimizing the current distribution with suitable DGS. For this purpose, structural designs have been optimized by parametric simulations in HFSS and CST MWS. Both the antennas can perform well in variety of wireless communication including WLAN IEEE 802.11 g/a (5.15–5.35 GHz and 5.725–5.825 GHz) and X-band applications including short range, tracking, missile guidance, and radar communication that ranges roughly from 8.29 to 11.4 GHz. The measured experimental results show that impedance bandwidth (S11 < −10 dB) of antenna with DGS is 100%. The antenna with DGS offers gain improvement by 2.7 dB for 13 GHz and 7 dB for 14 GHz. The performance of antenna with DGS is compared to conventional CPW-fed circular patch antenna (without DGS) in terms of reflection coefficient, radiation characteristics, and gain.

scholarly journals High gain 5G MIMO antenna for mobile base station

2019 ◽  
Vol 9 (1) ◽  
pp. 468 ◽  
Author(s):  
Yusnita Rahayu ◽  
Indah Permata Sari ◽  
Dara Incam Ramadhan ◽  
Razali Ngah
Keyword(s):  
Linear Array ◽  
Multiple Input Multiple Output ◽  
High Gain ◽  
Base Station ◽  
Impedance Bandwidth ◽  
Single Element ◽  
Mimo Antenna ◽  
Input Multiple Output ◽  
Mobile Base Station ◽  
Mobile Base

This article presented a millimeter wave antenna which operated at 38 GHz for 5G mobile base station. The MIMO (Multiple Input Multiple Output) antenna consisted of 1x10 linear array configurations. The proposed antenna’s size was 88 x 98 mm^2  and printed on 1.575 mm-thick Rogers Duroid 5880 subsrate with dielectric constant of ε_r= 2.2 and loss tangent (tanδ) of 0.0009. The antenna array covered along the azimuth plane to provide the coverage to the users in omnidirection. The simulated results showed that the single element antenna had the reflection coefficient (S11) of -59 dB, less than -10 dB in the frequency range of 35.5 - 39.6 GHz. More than 4.1 GHz of impedance bandwidth was obtained. The gain of the antenna linear array was 17.8 dBi while the suppression of the side lobes was -2.7 dB.  It showed a high array gain throughout the impedance bandwidth with overall of VSWR were below 1.0646. It designed using CST microwave studio.

Sub-terahertz (THz) antenna for Internet of Things and 6G Communication

Frequenz ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Hamsakutty Vettikalladi ◽  
Waleed Tariq Sethi ◽  
Wonsuk Ko
Keyword(s):  
Internet Of Things ◽  
Wireless Communication ◽  
Communication Systems ◽  
Side Lobe ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Single Element ◽  
High Frequency Structure Simulator ◽  
Sixth Generation ◽  
Intelligent Communication

Abstract Sub-terahertz (THz) technology is expected to deliver exceptional data rates for future sixth generation wireless communication systems especially for intelligent communication among devices falling under the Internet of Things (IoT) category. Moving from current 5G millimeter wave (mmW) technology towards THz spectrum will eventually provide unprecedented solutions that will guarantee higher transmission rates and channel capacity for any wireless communication system. With various electronic and wireless components working together to fulfill this promise, high gain antennas having compact profile is one such technology that will aid in achieving sub-THz communication while offering low path and power losses with reliable and fast data transfers. In this context, this work proposes a novel deformed patch antenna operating in the sub-THz spectrum i.e. at 300 GHz band. The proposed antenna is fed via a microstrip line following the proximity coupled feeding technique. Utilizing this technique provides a wide impedance bandwidth with a broadside radiation pattern having minimum side lobe levels of around −12 dB and a directivity of 10–15 dBi for the single and array elements respectively. The proposed design has a small footprint of 1.5 × 1.5 × 0.06 mm3 for the single element while the array element has dimensions of 6 × 5 × 0.06 mm3. Both the designs have been simulated in Computer Simulation Technology-Microwave Studio (CST-MWS) and the results verified via high-frequency structure simulator (HFSS) simulator. The results confirm the viability of the proposed designs to be potential candidates for future sixth generation and IoT based applications.

scholarly journals Millimeter Wave Fabry-Perot Resonator Antenna Fed by CPW with High Gain and Broadband

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Xue-Xia Yang ◽  
Guan-Nan Tan ◽  
Bing Han ◽  
Hai-Gao Xue
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Dielectric Substrate ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Broad Bandwidth ◽  
Low Profile ◽  
Fabry Perot

A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth ofS11less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

Novel dual-band multistrip monopole antenna with defected ground structure for WLAN/IMT/BLUETOOTH/WIMAX applications

2013 ◽  
Vol 6 (1) ◽  
pp. 93-100 ◽  
Author(s):  
Jaswinder Kaur ◽  
Rajesh Khanna ◽  
Machavaram Kartikeyan
Keyword(s):  
Wireless Local Area Network ◽  
Local Area Network ◽  
Design Procedure ◽  
Monopole Antenna ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Simulation Results

In the present work, a novel multistrip monopole antenna fed by a cross-shaped stripline comprising one vertical and two horizontal strips has been proposed for wireless local area network (WLAN)/Industrial, Scientific, and Medical band (ISM)/International Mobile Telecommunication (IMT)/BLUETOOTH/Worldwide Interoperability for Microwave Access (WiMAX) applications. The designed antenna has a small overall size of 20 × 30 mm2. The goal of this paper is to use defected ground structure (DGS) in the proposed antenna design to achieve dual-band operation with appreciable impedance bandwidth at the two operating modes satisfying several communication standards simultaneously. The antenna was simulated using Computer Simulation Technology Microwave Studio (CST MWS) V9 based on the finite integration technique (FIT) with perfect boundary approximation. Finally, the proposed antenna was fabricated and some performance parameters were measured to validate against simulation results. The design procedure, parametric analysis, simulation results along with measurements for this multistrip monopole antenna using DGS operating simultaneously at WLAN (2.4/5.8 GHz), IMT (2.35 GHz), BLUETOOTH (2.45 GHz), and WiMAX (5.5 GHz) are presented.

scholarly journals Design of a Substrate-Integrated Fabry-Pérot Cavity Antenna forK-Band Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Truong Khang Nguyen ◽  
Ikmo Park
Keyword(s):  
Coplanar Waveguide ◽  
Ground Plane ◽  
Cost Effective ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Hole Array ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
Fabry Perot ◽  
Feeding Structure

This paper presents the design of a planar, low-profile, high-gain, substrate-integrated Fabry-Pérot cavity antenna forK-band applications. The antenna consists of a frequency selective surface (FSS) and a planar feeding structure, which are both lithographically patterned on a high-permittivity substrate. The FSS is made of a circular hole array that acts as a partially reflecting mirror. The planar feeding structure is a wideband leaky-wave slit dipole fed by a coplanar waveguide whose ground plane acts as a perfect reflective mirror. The measured results show that the proposed antenna has an impedance bandwidth of more than 8% (VSWR ≤ 2), a maximum gain of 13.1 dBi, and a 3 dB gain bandwidth of approximately 1.3% at a resonance frequency of around 21.6 GHz. The proposed antenna features low-profile, easy integration into circuit boards, mechanical robustness, and excellent cost-effective mass production suitability.

CPW fed rectangular rings-based patch antenna with DGS for WLAN/UNII applications

2019 ◽  
Vol 11 (5-6) ◽  
pp. 523-531 ◽  
Author(s):  
Geetanjali Singla ◽  
Rajesh Khanna ◽  
Davinder Parkash
Keyword(s):  
Microstrip Antenna ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Local Area ◽  
High Gain ◽  
Area Network ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
National Information Infrastructure ◽  
National Information

AbstractThe spectral congestion in existing Industrial, Scientific, and Medical (ISM) Wireless Local Area Network (WLAN) bands has led to the emergence of new ISM bands (Unlicensed National Information Infrastructure (UNII)) from 5.150 to 5.710 GHz. In this paper, a simple uniplanar, high gain, microstrip antenna is designed, fabricated, and tested for existing WLAN and new UNII standards. The proposed antenna provides dualband operation by joining two rectangular rings and cutting Defected Ground Structure in the Coplanar Wave Guide (CPW) feed. The experimental and simulation results show good return loss characteristics and stable radiation pattern over the desired frequency bands ranging from 2.20 to 2.65 GHz (WLAN band) at a lower frequency and from 5.0 to 5.45 GHz (UNII-1/UNII-2 bands). The measured peak gains are 5.5 and 4.9 dBi at 2.45 GHz (WLAN band) and 5.15 GHz (UNII band), respectively.

Sign in / Sign up

Export Citation Format

Share Document