scholarly journals Meander-Line Slot-Loaded High-Sensitivity Microstrip Patch Sensor Antenna for Relative Permittivity Measurement

Sensors ◽  
2019 ◽  
Vol 19 (21) ◽  
pp. 4660 ◽  
Author(s):  
Junho Yeo ◽  
Jong-Ig Lee
Keyword(s):  
Patch Antenna ◽  
Relative Permittivity ◽  
High Sensitivity ◽  
Dielectric Constants ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
High Relative Permittivity ◽  
Rectangular Slit ◽  
Meander Line ◽  
Good Agreement

A high-sensitivity microstrip patch sensor antenna (MPSA) loaded with a meander-line slot (MLS) is proposed for the measurement of relative permittivity. The proposed MPSA was designed by etching the MLS along the radiating edge of the patch antenna, and it enhanced the relative permittivity sensitivity with an additional effect of miniaturization in the patch size by increasing the slot length. The sensitivity of the proposed MPSA was compared with that of a conventional rectangular patch antenna and a rectangular slit (RS)-loaded MPSA, by measuring the shift in the resonant frequency of the input reflection coefficient. Three MPSAs were designed and fabricated on a 0.76 mm-thick RF-35 substrate to resonate at 2.5 GHz under unloaded conditions. Sensitivity comparison was performed by using five different standard dielectric samples with dielectric constants ranging from 2.17 to 10.2. The experiment results showed that the sensitivity of the proposed MPSA is 6.84 times higher for a low relative permittivity of 2.17, and 4.57 times higher for a high relative permittivity of 10.2, when compared with the conventional MPSA. In addition, the extracted relative permittivity values of the five materials under tests showed good agreement with the reference data.

scholarly journals Slot-Loaded Microstrip Patch Sensor Antenna for High-Sensitivity Permittivity Characterization

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 502 ◽  
Author(s):  
Junho Yeo ◽  
Jong-Ig Lee
Keyword(s):  
Resonant Frequency ◽  
Patch Antenna ◽  
High Sensitivity ◽  
Dielectric Constants ◽  
Resonant Frequencies ◽  
Rectangular Slot ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Planar Materials ◽  
Measured Sensitivity

A slot-loaded microstrip patch sensor antenna is proposed to enhance sensitivity in measuring the permittivity of planar materials. A thin rectangular slot was etched along the radiating edge of a rectangular patch antenna fed by a microstrip transmission line. Two resonant frequencies were created at a lower frequency compared to the single resonant frequency of a conventional ordinary patch antenna. The sensitivity of the proposed slot-loaded patch antenna was measured by the shift in the resonant frequency of the input reflection coefficient when the planar dielectric superstrate was placed above the patch, and was compared with that of a conventional patch antenna without the slot. The two antennas were designed and fabricated on a 0.76 mm-thick RF-35 substrate for the first resonant frequency to resonate at 2.5 GHz under unloaded conditions. Five different standard dielectric samples with dielectric constants ranging from 2.17 to 10.2 were tested for sensitivity comparison. The experiment results showed that the measured sensitivity of the proposed patch antenna were 3.54 to 4.53 times higher, compared to a conventional patch antenna, for the five samples.

scholarly journals Metamaterial Embedded Wearable Rectangular Microstrip Patch Antenna

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
J. G. Joshi ◽  
Shyam S. Pattnaik ◽  
S. Devi
Keyword(s):  
Frequency Band ◽  
Patch Antenna ◽  
Low Cost ◽  
Microstrip Patch Antenna ◽  
Ieee 802.11A ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Bending Effect ◽  
Rectangular Microstrip Patch Antenna ◽  
Good Agreement

This paper presents an indigenous low-cost metamaterial embedded wearable rectangular microstrip patch antenna using polyester substrate for IEEE 802.11a WLAN applications. The proposed antenna resonates at 5.10 GHz with a bandwidth and gain of 97 MHz and 4.92 dBi, respectively. The electrical size of this antenna is0.254λ×0.5λ. The slots are cut in rectangular patch to reduce the bending effect. This leads to mismatch the impedance at WLAN frequency band; hence, a metamaterial square SRR is embedded inside the slot. A prototype antenna has been fabricated and tested, and the measured results are presented in this paper. The simulated and measured results of the proposed antenna are found to be in good agreement. The bending effect on the performance of this antenna is experimentally verified.

scholarly journals Design of Microstrip Patch Antenna for Dual-band Operation using Metal Ring Superstrate

2020 ◽  
Vol 8 (5) ◽  
pp. 4539-4543
Keyword(s):  
Patch Antenna ◽  
Dielectric Substrate ◽  
Microstrip Patch Antenna ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Metal Ring ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Lower Band ◽  
Good Agreement

In this paper, a dual-band generation in rectangular microstrip patch antenna (RMPA) using a superstrate metal ring has been proposed. In this configuration, a metal ring is placed above the rectangular patch with the support of two dielectric posts. The metal ring behaves as a superstrate layer and resonator for the lower band, the other band is generated by microstrip patch and hence the combined configuration metal ring and patch gives dual-band characteristics. The lower band resonates at 9 GHz with an impedance bandwidth of 6.8% and higher band at 11.35 GHz with impedance bandwidth of 3.1%. The co-polarized peak gain values at these frequencies are 8.2 dBi and 10.1 dBi respectively. This may be used in applications like airborne and naval-radar. The prototypes are fabricated using commercially available dielectric substrate (RT-Duriod r = 2.2 and thickness h =1.6 mm). The measured results show good agreement with the simulated predictions.

scholarly journals 28 GHz Microstrip Patch Antennas for Future 5G

2018 ◽  
Vol 2 (4) ◽  
pp. 1-6
Author(s):  
Keyword(s):  
Wireless Networks ◽  
Antenna Array ◽  
Patch Antenna ◽  
Structure Design ◽  
Slot Antenna ◽  
Potential Candidate ◽  
Significant Activity ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Compact Size

Recently, the industry and academia there is significant activity in research and development towards the next generation micro and Pico cellular wireless Networks (5th generation). This paper presents, a structure design of microstrip patch antenna array operate at the central frequency of 28 GHz waveband is proposed. The patch antenna array consists of four elements with rectangular patch and uniform distribution. It has a compact size of 26.51 x 20.37 mm with operating frequency at 28 GHz. The inset feed technique is used for the matching between radiating patch and the 50Ω microstrip feedline. The proposed 2x2 antenna array successfully improve the antenna gain up to 8.393dB compare to existing CRLH TL CPW antenna with 2.99 dB, wideband antenna with 7.1 dB and 3.7 dB for broadband elliptical-shaped slot antenna. As a conclusion, the directivity of 10.13 db and efficiency is higher than 80% considered as a potential candidate for the 5G wireless networks and applications.

scholarly journals Microstrip patch antenna with metamaterial using superstrate technique for wireless communication

2021 ◽  
Vol 10 (4) ◽  
pp. 2055-2061
Author(s):  
Rasha Mahdi Salih ◽  
Ali Khalid Jassim
Keyword(s):  
Wireless Communications ◽  
Reflection Coefficient ◽  
Wireless Communication ◽  
Patch Antenna ◽  
Relative Permittivity ◽  
Microstrip Antenna ◽  
Microstrip Patch Antenna ◽  
Antenna Gain ◽  
Microstrip Patch ◽  
Antenna Performance

This work builds a metamaterial (MTM) superstrate loaded on a patch of microstrip antenna for wireless communications. The MTM superstrate is made up of four G-shaped resonators on FR-4 substrate with a relative permittivity of 4.4 and has a total area of (8×16) mm2, and is higher than the patch. The MTM superstrate increases antenna gain while also raising the input reflection coefficient. When it is 9 mm above the patch, the gain increased from 3.28 dB to 6.02 dB, and when it is 7 mm above the patch, the input reflection coefficient was enhanced from -31.217 dB to -45.8 dB. When the MTM superstrate loaded antenna was compared to the traditional unloaded antenna, it was discovered that metamaterials have a lot of potential for improving antenna performance.

scholarly journals Low Cross-Polarization Improved-Gain Rectangular Patch Antenna

Electronics ◽  
2019 ◽  
Vol 8 (10) ◽  
pp. 1189 ◽  
Author(s):  
Anurag Singh ◽  
Sandip Vijay ◽  
Rudra Narayan Baral
Keyword(s):  
Patch Antenna ◽  
Frequency Selective Surface ◽  
Cross Polarization ◽  
Gain Enhancement ◽  
Rectangular Patch ◽  
Shorting Pin ◽  
Half Power ◽  
Broadside Radiation ◽  
Polarization Level ◽  
Good Agreement

In this paper, a low cross-polarization improved-gain rectangular patch antenna is presented. A patch-ground shorting pin with defected patch structure (DPS) is introduced to suppress the cross-polarization level. A High Reflective Frequency Selective Surface (HRFSS) superstrate is designed and placed over the proposed antenna at an optimized position to intensify the gain. To characterize the unit-cell of the superstrate, its transmission characteristics are extracted and discussed. Integration of the superstrate achieves a beam contraction resulting in a gain enhancement to 10.65 dBi. The proposed antenna has perfect broadside radiation with a cross-polarization level of below −30 dB in the entire half power beamwidth. The prototype of the antenna exhibits good agreement between experimental and simulated results.

Circularly Polarized Rectangular Microstrip Patch Antenna with Finite Ground Plane

2015 ◽  
Vol 4 (2) ◽  
pp. 74
Author(s):  
Sanyog Rawat ◽  
Kamlesh Kumar Sharma
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Axial Ratio ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Microstrip Patch ◽  
Rectangular Patch

<p class="Abstract"><span style="font-weight: normal;">In this paper a new geometry of patch antenna is proposed with improved bandwidth and circular polarization. The radiation performance of circularly polarized rectangular patch antenna is investigated by applying IE3D simulation software and its performance is compared with that of conventional rectangular patch antenna.</span> <span style="font-weight: normal;">Finite Ground truncation technique is used to obtain the desired results. The simulated return loss, axial ratio and smith chart with frequency for the proposed antenna is reported in this paper. It is shown that by selecting suitable ground-plane dimensions, air gap and location of the slits, the impedance bandwidth can be enhanced upto 10.15 % as compared to conventional rectangular patch (4.24%) with an axial ratio bandwidth of 4.05%.</span></p><p> </p><p> </p>

Gain enhancement of microstrip patch antenna using Sierpinski fractal-shaped EBG

2015 ◽  
Vol 8 (6) ◽  
pp. 915-919 ◽  
Author(s):  
Neeraj Rao ◽  
Dinesh Kumar Vishwakarma
Keyword(s):  
Patch Antenna ◽  
High Frequency ◽  
Microstrip Patch Antenna ◽  
Patch Antennas ◽  
Electromagnetic Band Gap ◽  
Gain Enhancement ◽  
Microstrip Patch Antennas ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Frequency Components

This is the first report on novel mushroom-type electromagnetic band gap (EBG) structures, consisting of fractal periodic elements, used for enhancing the gain of microstrip patch antennas. Using CST Microwave studio the performance of rectangular patch antenna has been examined on proposed fractal EBG substrates. It is found that fractal EBGs are more effective in suppressing surface wave thus resulting in higher gain. The gain of rectangular patch has been improved from 6.88 to 10.67 dBi. The proposed fractal EBG will open new avenues for the design and development of variety of high-frequency components and devices with enhanced performance.

Single-feed circularly polarized stacked patch antenna with small-frequency ratio for dual-band wireless applications

2015 ◽  
Vol 8 (8) ◽  
pp. 1207-1213 ◽  
Author(s):  
Sachin Kumar ◽  
Binod K. Kanaujia ◽  
Mukesh K. Khandelwal ◽  
A.K. Gautam
Keyword(s):  
Patch Antenna ◽  
Frequency Ratio ◽  
Axial Ratio ◽  
Dual Band ◽  
Radiation Characteristics ◽  
Small Frequency ◽  
Circularly Polarized ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Good Agreement

A single-feed dual-band circularly polarized stacked microstrip patch antenna with a small-frequency ratio is presented. Two pair of orthogonal slits is cut on the lower circular patch for achieving circular polarization and truncated corner square patch is used as the upper parasitic element. The frequency ratio of the dual-band is 1.03. The 3 dB axial ratio bandwidth is 1.3% for the upper band and 1.1% for the lower band. Proposed structure is fabricated on the FR-4 epoxy substrate and fed by SMA connector. The measured results are in good agreement with the theoretical and simulated results. The antenna shows stable radiation characteristics in both bands of operation.

scholarly journals Metamaterial Loaded Rectangular Patch Antenna for Wireless Communication Application

2021 ◽  
Vol 9 (3) ◽  
pp. 193-197
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Microstrip Patch Antenna ◽  
Negative Permittivity ◽  
Electromagnetic Analysis ◽  
Analysis Tool ◽  
Network Analyzer ◽  
Microstrip Patch ◽  
Rectangular Patch

In this paper, a metamaterial based compact multiband rectangular microstrip patch antenna is proposed. The return loss of metamaterial loaded microstrip patch antenna obtained at the resonant frequency 2.4GHz. The metamaterial structure printed on FR4 substrate at hight of 1.6mm from the ground plane. The FR4 substrate has 4.4 dielectric constant.These metamterial structures are periodic in nature and possesses negative permittivity and negative permeability. The greatest advantage of metamaterial loading will be miniaturization. This metamterial loaded rectangular patch antenna is simulated and tested using HFSS Simulator, where an electromagnetic analysis tool is used. The fabricated antennas results are measured using Vector Network Analyzer (VNA).

Sign in / Sign up

Export Citation Format

Share Document