scholarly journals Design of Cavity-Backed Bow-Tie Antenna with Matching Layer for Human Body Application

Sensors ◽  
2019 ◽  
Vol 19 (18) ◽  
pp. 4015 ◽  
Author(s):  
Jeong ◽  
Park ◽  
Lee
Keyword(s):  
Reflection Coefficient ◽  
Human Body ◽  
Electromagnetic Interference ◽  
Impedance Matching ◽  
Human Head ◽  
Impedance Match ◽  
Broadband Antenna ◽  
Matching Layer ◽  
Antenna Performance ◽  
Bow Tie

This paper presents the broadband antenna for the microwave radiometric sensing of internal body temperature. For broadband operation, the bow-tie antenna was designed and backed with a cylindrical cavity, which decreased environmental electromagnetic interference and also improved the directivity of the antenna. The broadband impedance-transforming balun in microstrip form was also designed to feed the bow-tie antenna, and was located inside the cavity. An impedance-matching dielectric layer (IMDL) was introduced on top of the bow-tie antenna, for impedance match with the human body with high permittivity. The fabricated antenna was measured in free space with the IMDL removed, showing an input reflection coefficient lower than −10 dB from 2.64 to > 3.60 GHz with antenna gain over 6.0 dBi and radiation efficiency over 74.7% from 2.7 to 3.5 GHz. The IMDL was re-installed on the cavity-backed bow-tie antenna to measure the antenna performance for the human head with relative permittivity of about 40. The measured reflection coefficient was as low as −28.9 dB at 2.95 GHz and lower than −10 dB from 2.65 to > 3.5 GHz. It was also shown that the designed antenna recovered a good impedance match by adjusting the permittivity and thickness of the IMDL for the different parts of the human body with different permittivities.

scholarly journals A Triple Band Bow Tie Array Antenna Using Both-sided MIC Technology

2018 ◽  
Vol 8 (5) ◽  
pp. 3038
Author(s):  
Akimun Jannat Alvina ◽  
Samia Sabrin ◽  
Mohammad Istiaque Reja ◽  
Jobaida Akhtar
Keyword(s):  
Impedance Matching ◽  
Axial Ratio ◽  
Array Antenna ◽  
Matching Problem ◽  
Compact Structure ◽  
Antenna Performance ◽  
Linearly Polarized ◽  
Feed Network ◽  
Feed Networks ◽  
Bow Tie

<span>A single-fed linearly polarized 2x2 microstrip bow tie array antenna is proposed. The feed network has microstrip line and slot line where microstrip-slot branch circuit is connected in parallel. The feed network of the array is designed using both-sided MIC Technology to overcome the impedance matching problem of conventional feed networks. The 2x2 half bow tie array antenna is also truncated with spur lines for optimization of antenna performance. The array antenna unit can be realized in very simple and compact structure, as all the antenna elements and the feeding circuit is arranged on a Teflon glass fiber substrate without requiring any external network. The design frequency of the proposed antenna is 5 to 8 GHz (CBand) and the obtained peak gain is 12.41 dBi. The resultant axial ratio indicates that linear polarization is achieved. </span>

scholarly journals Planar MIMO Antenna with Slits for WBAN Applications

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Do-Gu Kang ◽  
Jinpil Tak ◽  
Jaehoon Choi
Keyword(s):  
Resonant Frequency ◽  
Human Body ◽  
Impedance Matching ◽  
Ground Plane ◽  
Antenna Size ◽  
Mimo Antenna ◽  
Ism Band ◽  
Antenna Performance

A planar MIMO antenna with slits for WBAN applications is proposed. The antenna consists of two PIFAs, ground pads, and two slits. By adding ground pads, the antenna size is reduced with improved impedance matching. Through two slits in a ground plane, the isolation characteristic is improved and the resonant frequency can be controlled. To analyze the antenna performance on a human body, the proposed antenna on a human equivalent flat phantom is investigated through simulations. Regardless of the existence of the phantom, the antenna operates in 2.4 GHz ISM band with the isolation higher than 18 dB.

scholarly journals Feasibility Study of Enhancing Microwave Brain Imaging Using Metamaterials

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5472 ◽  
Author(s):  
Eleonora Razzicchia ◽  
Ioannis Sotiriou ◽  
Helena Cano-Garcia ◽  
Efthymios Kallos ◽  
George Palikaras ◽  
...  
Keyword(s):  
Brain Imaging ◽  
Impedance Matching ◽  
Human Head ◽  
Split Ring Resonator ◽  
Case Scenario ◽  
Split Ring ◽  
Matching Layer ◽  
Dielectric Target ◽  
The Brain ◽  
Brain Haemorrhage

We present an approach to enhance microwave brain imaging with an innovative metamaterial (MM) planar design based on a cross-shaped split-ring resonator (SRR-CS). The proposed metasurface is incorporated in different setups, and its interaction with EM waves is studied both experimentally and by using CST Microwave Studio® and is compared to a “no MM” case scenario. We show that the MM can enhance the penetration of the transmitted signals into the human head when placed in contact with skin tissue, acting as an impedance-matching layer. In addition, we show that the MM can improve the transceivers’ ability to detect useful “weak” signals when incorporated in a headband scanner for brain imaging by increasing the signal difference from a blood-like dielectric target introduced into the brain volume. Our results suggest that the proposed MM film can be a powerful hardware advance towards the development of scanners for brain haemorrhage detection and monitoring.

Flexible and moon-shaped slot UWB implantable antenna design for head implants

2017 ◽  
Vol 9 (8) ◽  
pp. 1559-1567 ◽  
Author(s):  
Roshanak Elyassi ◽  
Gholamreza Moradi
Keyword(s):  
Flexible Substrate ◽  
Impedance Matching ◽  
Human Head ◽  
Mean Value ◽  
Ultra Wideband ◽  
Antenna Design ◽  
Frequency Range ◽  
Antenna Performance ◽  
Implantable Antenna ◽  
Simulation Results

In this paper, we present a novel flexible moon-shaped slot implantable antenna for neural recording systems and head implants. It covers both medical Industrial, Scientific and Medical band (2.45 GHz) and impulse ratio ultra-wideband (IR-UWB) frequency range (3.1–10.6 GHz) for forward and backward telemetry applications. It has a simple and miniaturized structure in comparison with the antennas reported in the other researches. Furthermore, for adapting with natural curvature of human head, a flexible substrate is chosen with a good antenna performance under the bending. The proposed antenna is analyzed in a multi-layer box model of head tissues to speed up the antenna design procedures. On the basis of the simulation results, we achieved the good impedance matching over the desired frequency range (S11below −10 dB). Far-field characteristics are considered, as well. The directivity is in suitable range for UWB short-range communications and its mean value is 3.84 dBi. Finally, to take into account patents’ safety regulations and the effective isotropic radiated power restriction in the desired frequency range, the maximum power of transmitter has been calculated. A phantom containing a mixture of sugar and water is used to test the fabricated antenna. The measured parameters are well matched to the full-wave simulation results.

Investigation of e-textile dipole antenna performance based on embroidery parameters

2021 ◽  
pp. 004051752110134
Author(s):  
Daniel Agu ◽  
Rachel J Eike ◽  
Allyson Cliett ◽  
Dawn Michaelson ◽  
Rinn Cloud ◽  
...  
Keyword(s):  
Frequency Band ◽  
Impedance Matching ◽  
Dipole Antenna ◽  
Water Soluble ◽  
Wearable Sensor ◽  
Dipole Antennas ◽  
Antenna Performance ◽  
Large Production ◽  
Lower Transmission ◽  
The Ideal

E-textile antennas have the potential to be the premier on-body wearable sensor. Embroidery techniques, which can be applied to produce e-textile antennas, assist in large production volumes and fast production speeds. This paper focuses on the effects of three commonly used embroidery parameters, namely stitch type, conductive thread location, and stabilizer, on the performance of embroidered dipole antennas in order to determine the ideal embroidery combination for optimal antenna performance. Fifty-four dipole antenna samples were fabricated and measured at the industrial, scientific, and medical (ISM) frequency band of 2.45 GHz. The results of this study show that machine-embroidered antenna designs with satin stitches resonate at a lower frequency and exhibit a lower transmission gain compared with those made with contour stiches, and the conductive thread location in the bobbin location plus the use of a water-soluble stabilizer can help improve impedance matching.

scholarly journals Investigation on Wireless Link for Medical Telemetry Including Impedance Matching of Implanted Antennas

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1431
Author(s):  
Ilkyu Kim ◽  
Sun-Gyu Lee ◽  
Yong-Hyun Nam ◽  
Jeong-Hae Lee
Keyword(s):  
Real Time ◽  
Human Body ◽  
Near Field ◽  
Impedance Matching ◽  
The Body ◽  
Field Pattern ◽  
Communication Link ◽  
Far Field ◽  
Antenna Coupling ◽  
Medical Telemetry

The development of biomedical devices benefits patients by offering real-time healthcare. In particular, pacemakers have gained a great deal of attention because they offer opportunities for monitoring the patient’s vitals and biological statics in real time. One of the important factors in realizing real-time body-centric sensing is to establish a robust wireless communication link among the medical devices. In this paper, radio transmission and the optimal characteristics for impedance matching the medical telemetry of an implant are investigated. For radio transmission, an integral coupling formula based on 3D vector far-field patterns was firstly applied to compute the antenna coupling between two antennas placed inside and outside of the body. The formula provides the capability for computing the antenna coupling in the near-field and far-field region. In order to include the effects of human implantation, the far-field pattern was characterized taking into account a sphere enclosing an antenna made of human tissue. Furthermore, the characteristics of impedance matching inside the human body were studied by means of inherent wave impedances of electrical and magnetic dipoles. Here, we demonstrate that the implantation of a magnetic dipole is advantageous because it provides similar impedance characteristics to those of the human body.

Selectivity and in-band impedance enhancement of a compact slot antenna with defected ground structures

2019 ◽  
Vol 11 (10) ◽  
pp. 1010-1016
Author(s):  
Hailong Yang ◽  
Xiaoli Xi ◽  
Lili Wang ◽  
Yuchen Zhao ◽  
Xiaomin Shi
Keyword(s):  
Reflection Coefficient ◽  
Impedance Matching ◽  
Ultra Wideband ◽  
Band Edge ◽  
Slot Antenna ◽  
Defected Ground Structure ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Uwb Antennas ◽  
Low Pass

AbstractIn this study, a new ultra-wideband (UWB) band-edge selectivity antenna with a modified radiation slot using defected ground structure (DGS) is presented to obtain bandpass filtering reflection coefficient and gain performance. The well-designed DGS is designed on backside metallic of the substrate and can be seen as a low-pass filter that provides a good roll-off at a higher frequency. By connecting the DGS and the stepped slot and making them merge with each other, good cut-off property in the upper passband and better in-band impedance characteristics are obtained. Measured results show that the proposed design not only shows good band-edge selectivity in reflection coefficient and gain performance but also has a good impedance matching of −13.5 dB reflection coefficients and a good radiation efficiency of 90% in the operating frequencies. The measured bandwidth defined with the reflection coefficient less than −10 dB is from 3.1–11.2 GHz. Furthermore, the size of the filtering UWB antenna is 22 mm × 12 mm, which is smaller than many individual UWB antennas and UWB filters.

scholarly journals Microwave absorption and mechanical properties of double-layer cement-based composites containing different replacement levels of fly ash

2018 ◽  
Vol 25 (4) ◽  
pp. 707-714 ◽  
Author(s):  
Yuefang Zhang ◽  
Shunhua Liu ◽  
wanJun Hao
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Double Layer ◽  
Impedance Matching ◽  
X Ray Diffraction ◽  
Replacement Ratio ◽  
Matching Layer ◽  
Optimal Replacement ◽  
Zn Ferrite ◽  
Absorbing Layer

Abstract Double-layer absorbing cement-based composites with the thickness of 10 mm were prepared, including different replacement levels of fly ash (FA) in the absorbing layer as well as the matching layer for impedance matching. Waste polyethylene terephthalate bottle fragment was introduced as electromagnetic transparent reinforcement aggregate. Carbon black was used to be original absorbent in the absorbing layer. The microstructure and electromagnetic parameters of FA were closely looked at through scanning electron microscope, X-ray diffraction, and analyzer of vector network. The absorption and mechanical properties of cement-based composites were tested. It turned out that when the optimal replacement ratio of FA in the absorbing layer and matching layer gets to 50%:30%, the minimum value of reflection loss achieves −22.3 dB at 13.2 GHz; also, the value of absorption bandwidth that is effective (<−8 dB) is 6.4 GHz. Ni-Zn ferrite proves to be a feasible absorbent that is additional for the matching layer compared to what is added to the absorbing layer. The compressive strength of all the mixtures decreased, while the flexural strength decreased first and then increased with the rise of the FA replacement level.

Sign in / Sign up

Export Citation Format

Share Document