scholarly journals Hydrogen Sensing Using Paper Sensors with Pencil Marks Decorated with Palladium

Sensors ◽  
2019 ◽  
Vol 19 (14) ◽  
pp. 3050 ◽  
Author(s):  
Nam Hee Lee ◽  
Un-Bong Baek ◽  
Seung-Hoon Nahm
Keyword(s):  
Gas Sensors ◽  
Gas Sensing ◽  
Low Cost ◽  
Pd Nanoparticles ◽  
Reaction Rates ◽  
Hydrogen Sensing ◽  
Wide Range ◽  
The Relationship ◽  
Paper Method ◽  
Wide Usage

Paper-based sensors fabricated using the pencil-on-paper method are expected to find wide usage in many fields owing to their low cost and high reproducibility. Here, hydrogen (H2) detection was realized by applying palladium (Pd) nanoparticles (NPs) to electronic circuits printed on paper using a metal mask and a pencil. We confirmed that multilayered graphene was produced by the pencil, and then characterized Pd NPs were added to the pencil marks. To evaluate the gas-sensing ability of the sensor, its sensitivities and reaction rates in the presence and absence of H2 were measured. In addition, sensing tests performed over a wide range of H2 concentrations confirmed that the sensor had a detection limit as low as 1 ppm. Furthermore, the sensor reacted within approximately 50 s at all H2 concentrations tested. The recovery time of the sensor was 32 s at 1 ppm and 78 s at 1000 ppm. Sensing tests were also performed using Pd NPs of different sizes to elucidate the relationship between the sensing rate and catalyst size. The experimental results confirmed the possibility of fabricating paper-based gas sensors with a superior sensing capability and response rate.

scholarly journals Embedded Transdermal Alcohol Detection via a Finger Using SnO2 Gas Sensors

Sensors ◽  
2021 ◽  
Vol 21 (20) ◽  
pp. 6852
Author(s):  
Fatima Ezahra Annanouch ◽  
Virginie Martini ◽  
Tomas Fiorido ◽  
Bruno Lawson ◽  
Khalifa Aguir ◽  
...  
Keyword(s):  
Gas Sensors ◽  
Tin Dioxide ◽  
Gas Sensing ◽  
Low Cost ◽  
High Sensitivity ◽  
Rf Magnetron Sputtering ◽  
Alcohol Concentration ◽  
Invasive Technique ◽  
Clear Correlation ◽  
Wide Range

In this paper, we report the fabrication and characterization of a portable transdermal alcohol sensing device via a human finger, using tin dioxide (SnO2) chemoresistive gas sensors. Compared to conventional detectors, this non-invasive technique allowed us the continuous monitoring of alcohol with low cost and simple fabrication process. The sensing layers used in this work were fabricated by using the reactive radio frequency (RF) magnetron sputtering technique. Their structure and morphology were investigated by means of X-ray spectroscopy (XRD) and scanning electron microscopy (SEM), respectively. The results indicated that the annealing time has an important impact on the sensor sensitivity. Before performing the transdermal measurements, the sensors were exposed to a wide range of ethanol concentrations and the results displayed good responses with high sensitivity, stability, and a rapid detection time. Moreover, against high relative humidity (50% and 70%), the sensors remained resistant by showing a slight change in their gas sensing performances. A volunteer (an adult researcher from our volunteer group) drank 50 mL of tequila in order to realize the transdermal alcohol monitoring. Fifteen minutes later, the volunteer’s skin started to evacuate alcohol and the sensor resistance began to decline. Simultaneously, breath alcohol measurements were attained using a DRAGER 6820 certified breathalyzer. The results demonstrated a clear correlation between the alcohol concentration in the blood, breath, and via perspiration, which validated the embedded transdermal alcohol device reported in this work.

scholarly journals A Review of Carbon Nanotubes-Based Gas Sensors

2009 ◽  
Vol 2009 ◽  
pp. 1-24 ◽  
Author(s):  
Yun Wang ◽  
John T. W. Yeow
Keyword(s):  
Carbon Nanotubes ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Low Cost ◽  
High Surface ◽  
Hollow Structure ◽  
Volume Ratio ◽  
Fast Response ◽  
Sensing Technology ◽  
Structure Of Nanomaterials

Gas sensors have attracted intensive research interest due to the demand of sensitive, fast response, and stable sensors for industry, environmental monitoring, biomedicine, and so forth. The development of nanotechnology has created huge potential to build highly sensitive, low cost, portable sensors with low power consumption. The extremely high surface-to-volume ratio and hollow structure of nanomaterials is ideal for the adsorption of gas molecules. Particularly, the advent of carbon nanotubes (CNTs) has fuelled the inventions of gas sensors that exploit CNTs' unique geometry, morphology, and material properties. Upon exposure to certain gases, the changes in CNTs' properties can be detected by various methods. Therefore, CNTs-based gas sensors and their mechanisms have been widely studied recently. In this paper, a broad but yet in-depth survey of current CNTs-based gas sensing technology is presented. Both experimental works and theoretical simulations are reviewed. The design, fabrication, and the sensing mechanisms of the CNTs-based gas sensors are discussed. The challenges and perspectives of the research are also addressed in this review.

scholarly journals Tuning Stoichiometry and Structure of Pd-WO3−x Thin Films for Hydrogen Gas Sensing by High-Power Impulse Magnetron Sputtering

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5101
Author(s):  
Nirmal Kumar ◽  
Stanislav Haviar ◽  
Jiří Rezek ◽  
Pavel Baroch ◽  
Petr Zeman
Keyword(s):  
Magnetron Sputtering ◽  
High Power ◽  
Gas Sensing ◽  
Pulse Length ◽  
Pd Nanoparticles ◽  
Hydrogen Gas ◽  
Sensory Response ◽  
Hydrogen Sensing ◽  
Sensing Applications ◽  
Deposition Parameters

By tuning the deposition parameters of reactive high-power impulse magnetron sputtering, specifically the pulse length, we were able to prepare WO3−x films with various stoichiometry and structure. Subsequently, the films were annealed in air at moderate temperature (350 °C). We demonstrate that the stoichiometry of the as-deposited films influences considerably the type of crystalline phase formed in the annealed films. The appropriate sub-stoichiometry of the films (approx. WO2.76) enabled crystallization of the monoclinic phase during the annealing. This phase is favorable for hydrogen sensing applications. To characterize the sensory behavior of the films, the tungsten oxide films were decorated by Pd nanoparticles before annealing and were assembled as a conductometric gas sensor. The sensory response of the films that crystallized in the monoclinic structure was proven to be superior to that of the films containing other phases.

Gas Sensing Properties of TiO2 and SnO2 Nanopowders Obtained through Gel Combustion

2006 ◽  
Vol 45 ◽  
pp. 1828-1833
Author(s):  
Fabio A. Deorsola ◽  
P. Mossino ◽  
Ignazio Amato ◽  
Bruno DeBenedetti ◽  
A. Bonavita ◽  
...  
Keyword(s):  
Response Time ◽  
Metal Oxides ◽  
Gas Sensing ◽  
Low Cost ◽  
High Sensitivity ◽  
Fast Response ◽  
High Specific Surface Area ◽  
Research Field ◽  
Wide Range ◽  
Gel Combustion

Nanostructured semiconductor metal oxides have played a central role in the gas sensing research field, because of their high sensitivity, selectivity and low response time. Among all the processes, developed for the synthesis of nanostructured metal oxides, gel combustion seems to be the most promising route due to low-cost precursors and simplicity of the process. It combines chemical gelation and combustion, involving the formation of a gel from an acqueous solution and an exothermic redox reaction, yielding to very porous and softly agglomerated nanopowders. In this work, nanostructured tin oxide, SnO2, and titanium oxide, TiO2, have been synthesized through gel combustion. Powders showed nanometric particle size and high specific surface area. The so-obtained TiO2 and SnO2 nanopowders have been used as sensitive element of resistive λ sensor and ethanol sensor respectively, realized depositing films of nanopowders dispersed in water onto alumina substrates provided with Pt contacts and heater. TiO2-based sensors showed at high temperature good response, fast response time, linearity in a wide range of O2 concentration and long-term stability. SnO2-based sensors have shown high sensitivity to low concentrations of ethanol at moderate temperature.

Applications of Nanostructured Materials as Gas Sensors

2013 ◽  
Vol 201 ◽  
pp. 131-158 ◽  
Author(s):  
Ravi Chand Singh ◽  
Manmeet Pal Singh ◽  
Hardev Singh Virk
Keyword(s):  
Metal Oxide ◽  
Gas Sensors ◽  
Tin Dioxide ◽  
Gas Sensing ◽  
Dominant Role ◽  
Low Cost ◽  
Critical Role ◽  
Health And Safety ◽  
Chemical Route ◽  
Metal Oxide Sensors

Gas detection instruments are increasingly needed for industrial health and safety, environmental monitoring, and process control. To meet this demand, considerable research into new sensors is underway, including efforts to enhance the performance of traditional devices, such as resistive metal oxide sensors, through nanoengineering. The resistance of semiconductors is affected by the gaseous ambient. The semiconducting metal oxides based gas sensors exploit this phenomenon. Physical chemistry of solid metal surfaces plays a dominant role in controlling the gas sensing characteristics. Metal oxide sensors have been utilized for several decades for low-cost detection of combustible and toxic gases. Recent advances in nanomaterials provide the opportunity to dramatically increase the response of these materials, as their performance is directly related to exposed surface volume. Proper control of grain size remains a key challenge for high sensor performance. Nanoparticles of SnO2have been synthesized through chemical route at 5, 25 and 50°C. The synthesized particles were sintered at 400, 600 and 800°C and their structural and morphological analysis was carried out using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The reaction temperature is found to be playing a critical role in controlling nanostructure sizes as well as agglomeration. It has been observed that particle synthesized at 5 and 50°C are smaller and less agglomerated as compared to the particles prepared at 25°C. The studies revealed that particle size and agglomeration increases with increase in sintering temperature. Thick films gas sensors were fabricated using synthesized tin dioxide powder and sensing response of all the sensors to ethanol vapors was investigated at different temperatures and concentrations. The investigations revealed that sensing response of SnO2nanoparticles is size dependent and smaller particles display higher sensitivity. Table of Contents

Fabrication of a Carbon Nanotube Gas Sensor Microelectrodes and its Application for Ammonia Detection

2013 ◽  
Vol 431 ◽  
pp. 306-311
Author(s):  
Xiang Tao Ran ◽  
Zhi Wang ◽  
Li Yang
Keyword(s):  
Gas Sensors ◽  
High Performance ◽  
Gas Sensing ◽  
Structural Parameters ◽  
Low Cost ◽  
Manufacturing Method ◽  
Multi Walled Carbon Nanotubes ◽  
Ammonia Detection ◽  
Low Cost Manufacturing ◽  
Walled Carbon Nanotubes

With the increasing needs for high-performance gas sensors in industrial production, environmental monitoring and so on, the research on gas sensors is becoming more and more important. In this paper, the electric field intensity distribution simulation process of the interdigital microelectrodes (IMEs) is discussed in details to get the proper electrode structural parameters. The IMEs on the ITO surface with a minimum gap of about 4μm are achieved by lithography, which provides a reliable, low-cost manufacturing method. Sensitive components are made of the multi-walled carbon nanotubes modified materials. The gas-sensing property of the sensor is detected for ammonia. The experiment result shows that the performance of the nanomodified sensor is obviously improved.

ZnO-Based Gas Sensors Prepared by EPD and Hydrothermal Growth

2015 ◽  
Vol 654 ◽  
pp. 94-98 ◽  
Author(s):  
Roman Yatskiv ◽  
María Verde ◽  
Jan Grym
Keyword(s):  
Gas Sensors ◽  
Room Temperature ◽  
Gas Sensing ◽  
Low Cost ◽  
Zno Nanorods ◽  
Zno Films ◽  
Nanorod Arrays ◽  
Zno Nanorod Arrays ◽  
Current Voltage ◽  
Gas Sensing Properties

Arrays of vertically well aligned ZnO nanorods (NRs) were prepared on nanostructured ZnO films using a low temperature hydrothermal method. We propose the use of the low cost, environmentally friendly electrophoretic deposition technique (EPD) as seeding procedure, which allows the obtaining of homogeneous, well oriented nanostructured ZnO thin films. ZnO nanorod arrays were covered with graphite in order to prepare graphite/ZnO NRs junctions. These nanostructured junctions showed promising current-voltage rectifying characteristics and gas sensing properties at room temperature.

CNTFET Gas Sensors Using SWCNT Mats: Method for Low-cost Fabrication, Solution to Improve Selectivity, Experimental Results using Interfering Agents

2009 ◽  
Vol 1204 ◽  
Author(s):  
Paolo Bondavalli ◽  
Louis Gorintin ◽  
Pierre Legagneux ◽  
Didier Pribat ◽  
Laurent Caillier ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Gas Sensors ◽  
Field Effect ◽  
Gas Sensing ◽  
Field Effect Transistors ◽  
Low Cost ◽  
Experimental Results ◽  
Flexible Substrates ◽  
Metal Electrodes ◽  
Sensing Applications

AbstractThe first paper showing the great potentiality of Carbon Nanotubes Field Effect transistors (CNTFETs) for gas sensing applications was published in 2000 [1]. It has been demonstrated that the performances of this kind of sensors are extremely interesting: a sensitivity of around 100ppt (e.g. for NO2 [2]) has been achieved in 2003 and several techniques to improve selectivity have been tested with very promising results [2]. The main issues that have not allowed, up to now, these devices to strike more largely the market of sensors, have been the lack of an industrial method to obtain low-cost devices, a demonstration of their selectivity in relevant environments and finally a deeper study on the effect of humidity and the possible solutions to reduce it. This contribution deals with CNTFETs based sensors fabricated using air-brush technique deposition on large surfaces. Compared to our last contribution [3], we have optimized the air-brush technique in order to obtain high performances transistors (Log(Ion)/Log(Ioff) ∼ 5/6) with highly reproducible characteristics : this is a key point for the industrial exploitation. We have developed a machine which allows us the dynamic deposition on heated substrates of the SWCNT solutions, improving dramatically the uniformity of the SWCNT mats. We have performed tests using different solvents that could be adapted as a function of the substrates (e.g. flexible substrates). Moreover these transistors have been achieved using different metal electrodes (patented approach [4]) in order to improve selectivity. Results of tests using NO2, NH3 with concentrations between ∼ 1ppm and 10ppm will be shown during the meeting.

scholarly journals Hollow-Core Photonic Crystal Fiber Gas Sensing

Sensors ◽  
2020 ◽  
Vol 20 (10) ◽  
pp. 2996 ◽  
Author(s):  
Ruowei Yu ◽  
Yuxing Chen ◽  
Lingling Shui ◽  
Limin Xiao
Keyword(s):  
Photonic Crystal ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Deep Understanding ◽  
Industrial Applications ◽  
Hollow Core ◽  
Fundamental Limits ◽  
Practical Applications ◽  
Wide Range ◽  
Crystal Fibers

Fiber gas sensing techniques have been applied for a wide range of industrial applications. In this paper, the basic fiber gas sensing principles and the development of different fibers have been introduced. In various specialty fibers, hollow-core photonic crystal fibers (HC-PCFs) can overcome the fundamental limits of solid fibers and have attracted intense interest recently. Here, we focus on the review of HC-PCF gas sensing, including the light-guiding mechanisms of HC-PCFs, various sensing configurations, microfabrication approaches, and recent research advances including the mid-infrared gas sensors via hollow core anti-resonant fibers. This review gives a detailed and deep understanding of HC-PCF gas sensors and will promote more practical applications of HC-PCFs in the near future.

Sign in / Sign up

Export Citation Format

Share Document