scholarly journals Spectroscopy Transmittance by LED Calibration

Sensors ◽  
2019 ◽  
Vol 19 (13) ◽  
pp. 2951 ◽  
Author(s):  
Daniel Carreres-Prieto ◽  
Juan T. García ◽  
Fernando Cerdán-Cartagena ◽  
Juan Suardiaz-Muro
Keyword(s):  
Real Time ◽  
Light Emitting Diode ◽  
Research Work ◽  
Cost Effective ◽  
Spectral Width ◽  
Calibration Procedure ◽  
Pollution Monitoring ◽  
Light Emitting ◽  
Wide Range ◽  
Incandescent Lamps

Local administrations demand real-time and continuous pollution monitoring in sewer networks. Spectroscopy is a non-destructive technique that can be used to continuously monitor quality in sewers. Covering a wide range of wavelengths can be useful for improving pollution characterization in wastewater. Cost-effective and in-sewer spectrophotometers would contribute to accomplishing discharge requirements. Nevertheless, most available spectrometers are based on incandescent lamps, which makes it unfeasible to place them in a sewerage network for real-time monitoring. This research work shows an innovative calibration procedure that allows (Light-Emitting Diode) LED technology to be used as a replacement for traditional incandescent lamps in the development of spectrophotometry equipment. This involves firstly obtaining transmittance values similar to those provided by incandescent lamps, without using any optical components. Secondly, this calibration process enables an increase in the range of wavelengths available (working range) through a better use of the LED’s spectral width, resulting in a significant reduction in the number of LEDs required. Thirdly, this method allows important reductions in costs, dimensions and consumptions to be achieved, making its implementation in a wide variety of environments possible.

Towards a Novel Broadband Spectrally Dynamic Solid State Light Source

2005 ◽  
Vol 892 ◽  
Author(s):  
David Nicol ◽  
Shalini Gupta ◽  
Nola Li ◽  
Ali Asghar ◽  
Elton Graugnard ◽  
...  
Keyword(s):  
Solid State ◽  
Real Time ◽  
Light Source ◽  
Tunnel Junction ◽  
Light Emitting Diode ◽  
Contact Layer ◽  
Light Emitting ◽  
Wide Range ◽  
Multiple Wavelengths ◽  
Dynamic Source

AbstractThe developments of two major components of a three terminal dual wavelength LED for excitation of multiple phosphors are described. Such a configuration will be novel Broadband Spectrally Dynamic Light Emitting Diode (BSDLED). First, work towards a functional tunnel junction in the GaN system is discussed. The developments of p+ and n+ GaN layers are specifically discussed in relation to their use in a buried current spreading contact layer. Second, the analysis of several phosphors and their application in a spectrally dynamic source is explored. The response to multiple wavelengths of the phosphors is analyzed to create a light source that can be tuned in “real time” to a wide range of correlated color temperatures.

Low-Cost Label-Free Bio-Detection System Using Double-Sided Grating Waveguide Couplers

2015 ◽  
Author(s):  
Yi-Fan Ku ◽  
Hsun-Yuan Li ◽  
Yu-Chung Lin ◽  
Wen-Hsin Hsieh ◽  
Guo-En Chang
Keyword(s):  
Real Time ◽  
Detection System ◽  
Light Emitting Diode ◽  
Low Cost ◽  
Cost Effective ◽  
High Refractive Index ◽  
Optical Intensity ◽  
Label Free ◽  
Light Emitting ◽  
Label Free Detection

Low-cost label-free bio-sensing systems have long been desired to enable rapid, sensitive, quantitative, and high-throughput biosensing for bio-medical and chemical applications. Here we present an optical bio-detection system consists of injection-molded biosensors based on double-sided grating waveguide couplers and an optical intensity-based detection platform for low-cost, real-time, and label-free biosensing. The biosensors were fabricated combining injection-molding and sputtering techniques, providing unique advantages of low-cost and reduced production time. A simple and cost-effective optical intensity-based detection system employing a low-cost light emitting diode and a simple photodetector is also developed to perform label-free biosensing. We demonstrate that a high refractive index resolution of 6.43 × 10−5 RIU is achieved with this compact bio-sensing system, showing great promises for low-cost, real-time, label-free detection in bio-medical and chemical applications.

scholarly journals Performing Calibration of Transmittance by Single RGB-LED within the Visible Spectrum

Sensors ◽  
2020 ◽  
Vol 20 (12) ◽  
pp. 3492 ◽  
Author(s):  
Daniel Carreres-Prieto ◽  
Juan T. García ◽  
Fernando Cerdán-Cartagena ◽  
Juan Suardiaz-Muro
Keyword(s):  
Research Work ◽  
Visible Spectrum ◽  
Cost Effective ◽  
Calibration Procedure ◽  
Invasive Technique ◽  
Optical Elements ◽  
Simple Method ◽  
Non Invasive ◽  
Sewer Network ◽  
Incandescent Lamps

Spectrophotometry has proven to be an effective non-invasive technique for the characterization of the pollution load of sewer systems, enabling compliance with new environmental protection regulations. This type of equipment has costs and an energy consumption which make it difficult to place it inside a sewer network for real-time and massive monitoring. These shortcomings are mainly due to the use of incandescent lamps to generate the working spectrum as they often require the use of optical elements, such as diffraction gratings, to work. The search for viable alternatives to incandescent lamps is key to the development of portable equipment that is cheaper and with a lower consumption that can be used in different points of the sewer network. This research work achieved the following results in terms of the measured samples: First, the development a calibration procedure that enables the use of RGB-LED technology as a viable alternative to incandescent lamps, within the range of 510 to 645 nm, with high accuracy. Secondly, demonstration of a simple method to model the transmittance value of a specific wavelength without the need for optical elements, achieving a cost-effective equipment. Thirdly, it provides a simple method to obtain the transmittance based on the combination of RGB colors. Finally its viability is demonstrated for the spectral analysis of wastewater.

Achievement of 110-nm-Wide Spectral Width in Monolithic Tunnel-Junction Light-Emitting Diode

2021 ◽  
pp. 1-1
Author(s):  
Man-Fang Huang ◽  
Ya-Hsuan Shih ◽  
Jih-Yuan Chang ◽  
Yen-Lung Huang ◽  
Jinn-Kong Sheu ◽  
...  
Keyword(s):  
Tunnel Junction ◽  
Light Emitting Diode ◽  
Spectral Width ◽  
Light Emitting

scholarly journals LED Rail Signals: Full Hardware Realization of Apparatus with Independent Intensity by Temperature Changes

Electronics ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1291
Author(s):  
Giuseppe Schirripa Schirripa Spagnolo ◽  
Fabio Leccese
Keyword(s):  
Temperature Sensor ◽  
Energy Efficient ◽  
Light Emitting Diode ◽  
Junction Temperature ◽  
Light Emitting ◽  
Temperature Changes ◽  
Wide Range ◽  
International Regulations ◽  
Long Lifetime ◽  
Set Up

Nowadays, signal lights are made using light-emitting diode arrays (LEDs). These devices are extremely energy efficient and have a very long lifetime. Unfortunately, especially for yellow/amber LEDs, the intensity of the light is closely related to the junction temperature. This makes it difficult to design signal lights to be used in naval, road, railway, and aeronautical sectors, capable of fully respecting national and international regulations. Furthermore, the limitations prescribed by the standards must be respected in a wide range of temperature variations. In other words, in the signaling apparatuses, a system that varies the light intensity emitted according to the operating temperature is useful/necessary. In this paper, we propose a simple and effective solution. In order to adjust the intensity of the light emitted by the LEDs, we use an LED identical to those used to emit light as a temperature sensor. The proposed system was created and tested in the laboratory. As the same device as the ones to be controlled is used as the temperature sensor, the system is very stable and easy to set up.

scholarly journals A Device to Measure a Smoker’s Puffing Topography and Real-Time Puff-By-Puff “Tar” Delivery

2014 ◽  
Vol 26 (2) ◽  
Author(s):  
Sandra J. Slayford ◽  
Barrie E. Frost
Keyword(s):  
Real Time ◽  
Light Emitting Diode ◽  
Absolute Error ◽  
Average Error ◽  
Light Emitting ◽  
Light Obscuration ◽  
Test Study ◽  
Added Benefit ◽  
Volume Characteristics ◽  
The Relationship

AbstractA device for measuring the flow, duration and volume characteristics of human puffing behaviour when smoking cigarettes is described. Cigarettes are smoked through a holder comprising a measured pressure drop across a critical orifice. The holder also contains a Light Emitting Diode (LED) and photodetector that measures light obscuration in order to estimate nicotine-free dry particulate matter (NFDPM, “tar”) delivery. All data are recorded on a puff-by-puff basis and displayed in real time. These NFDPM estimates are known as optical “tar” (OT), and are derived from the calibration of the OT measurement versus gravimetric NFDPM yields of cigarettes under a range of smoking regimes. In a test study, puff volumes from 20-80 mL were recorded to ± 6.0% of a pre-set volume, with an absolute error of 4.7 mL for an 80 mL volume drawn on a lit cigarette, and an average error of less than 2.0 mL across the range 20-80 mL. The relationship between NFDPM and OT was linear (R2 = 0.99) and accurate to ± 1.3 mg per cigarette over the range 1-23 mg per cigarette. The device provides an alternative to the widely used part filter methodology for estimating mouth level exposure with an added benefit that no further laboratory smoking replication or analysis is required. When used in conjunction with the part filter methodology, the puffing behaviour recorded can explain anomalies in the data while providing a second independent estimate.

Low Cost Cooling Device for High Power LED Lamps

2020 ◽  
Author(s):  
Pamela Martinez-Vega ◽  
Araceli Lopez-Badillo ◽  
J. Luis Luviano-Ortiz ◽  
Abel Hernandez-Guerrero ◽  
Jaime G. Cervantes
Keyword(s):  
Reference Model ◽  
Light Emitting Diode ◽  
Low Cost ◽  
Cost Effective ◽  
Heat Sinks ◽  
Modern World ◽  
Type Model ◽  
Light Emitting

Abstract The modern world progressively demands more energy; according to forecasts energy consumption will grow at an average annual rate of 3 percent. Therefore, it is necessary to purchase products or devices that are efficient and environmentally friendly. Technology in LED (Light Emitting Diode) lighting is presented as an alternative to energy saving, since LEDs have proven to be extremely efficient, have a long service life and their cost-effective ratio is very good. However, the heat emitted by the LED chip must be dissipated effectively, since the overheating of the chip reduces the efficiency and lifetime of the lamp. Therefore, heat sinks that are reliable, efficient and inexpensive should be designed and built. The present work proposes new designs for heat sinks in LED lamps, some of the models in the design of the fins refer to the Fibonacci series. The models proposed in the present work that have a significant advantage are the Type 1E Model (5.2% mass savings and better thermal efficiency of 8.33%), GR Type 1 Model (3.12% lighter and 3.33% more efficient) and the GRL Type Model (4. 51% mass savings and 5.55% thermally more efficient) compared to the Type 2 Reference Model proposed by Jang et al. [12].

scholarly journals Real-Time Optical Monitoring of Endotracheal Tube Displacement

Biosensors ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 174
Author(s):  
Ramzan Ullah ◽  
Karl Doerfer ◽  
Pawjai Khampang ◽  
Faraneh Fathi ◽  
Wenzhou Hong ◽  
...  
Keyword(s):  
Endotracheal Tube ◽  
Real Time ◽  
Near Infrared ◽  
Ex Vivo ◽  
Light Emitting Diode ◽  
Clinical Care ◽  
Cost Effective ◽  
Infrared Light ◽  
In Vivo Experiments

Proper ventilation of a patient with an endotracheal tube (ETT) requires proper placement of the ETT. We present a sensitive, noninvasive, operator-free, and cost-effective optical sensor, called Opt-ETT, for the real-time assessment of ETT placement and alerting of the clinical care team should the ETT become displaced. The Opt-ETT uses a side-firing optical fiber, a near-infrared light-emitting diode, two photodetectors with an integrated amplifier, an Arduino board, and a computer loaded with a custom LabVIEW program to monitor the position of the endotracheal tube inside the windpipe. The Opt-ETT generates a visual and audible warning if the tube moves over a distance set by the operator. Displacement prediction is made using a second-order polynomial fit to the voltages measured from each detector. The system is tested on ex vivo porcine tissues, and the accuracy is determined to be better than 1.0 mm. In vivo experiments with a pig are conducted to test the performance and usability of the system.

scholarly journals Real-Time Healthcare Data Transmission for Remote Patient Monitoring in Patch-Based Hybrid OCC/BLE Networks

Sensors ◽  
2019 ◽  
Vol 19 (5) ◽  
pp. 1208 ◽  
Author(s):  
Moh. Hasan ◽  
Md. Shahjalal ◽  
Mostafa Chowdhury ◽  
Yeong Jang
Keyword(s):  
Real Time ◽  
Light Emitting Diode ◽  
Health Condition ◽  
High Signal ◽  
Network Access ◽  
Light Emitting ◽  
Healthcare Data ◽  
Led Array ◽  
Access Request ◽  
Remote Patient

Research on electronic healthcare (eHealth) systems has increased dramatically in recent years. eHealth represents a significant example of the application of the Internet of Things (IoT), characterized by its cost effectiveness, increased reliability, and minimal human eff ort in nursing assistance. The remote monitoring of patients through a wearable sensing network has outstanding potential in current healthcare systems. Such a network can continuously monitor the vital health conditions (such as heart rate variability, blood pressure, glucose level, and oxygen saturation) of patients with chronic diseases. Low-power radio-frequency (RF) technologies, especially Bluetooth low energy (BLE), play significant roles in modern healthcare. However, most of the RF spectrum is licensed and regulated, and the effect of RF on human health is of major concern. Moreover, the signal-to-noise-plus-interference ratio in high distance can be decreased to a considerable extent, possibly leading to the increase in bit-error rate. Optical camera communication (OCC), which uses a camera to receive data from a light-emitting diode (LED), can be utilized in eHealth to mitigate the limitations of RF. However, OCC also has several limitations, such as high signal-blockage probability. Therefore, in this study, a hybrid OCC/BLE system is proposed to ensure efficient, remote, and real-time transmission of a patient’s electrocardiogram (ECG) signal to a monitor. First, a patch circuit integrating an LED array and BLE transmitter chip is proposed. The patch collects the ECG data according to the health condition of the patient to minimize power consumption. Second, a network selection algorithm is developed for a new network access request generated in the patch circuit. Third, fuzzy logic is employed to select an appropriate camera for data reception. Fourth, a handover mechanism is suggested to ensure efficient network allocation considering the patient’s mobility. Finally, simulations are conducted to demonstrate the performance and reliability of the proposed system.

scholarly journals Light-Emitting-Diode-Based Multispectral Photoacoustic Computed Tomography System

Sensors ◽  
2019 ◽  
Vol 19 (22) ◽  
pp. 4861 ◽  
Author(s):  
Sumit Agrawal ◽  
Christopher Fadden ◽  
Ajay Dangi ◽  
Xinyi Yang ◽  
Hussain Albahrani ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Molecular Imaging ◽  
Photoacoustic Imaging ◽  
Light Emitting Diode ◽  
Low Cost ◽  
Tunable Laser ◽  
Cost Effective ◽  
Light Emitting ◽  
Multi Wavelength ◽  
Human Finger

Photoacoustic computed tomography (PACT) has been widely explored for non-ionizing functional and molecular imaging of humans and small animals. In order for light to penetrate deep inside tissue, a bulky and high-cost tunable laser is typically used. Light-emitting diodes (LEDs) have recently emerged as cost-effective and portable alternative illumination sources for photoacoustic imaging. In this study, we have developed a portable, low-cost, five-dimensional (x, y, z, t, λ ) PACT system using multi-wavelength LED excitation to enable similar functional and molecular imaging capabilities as standard tunable lasers. Four LED arrays and a linear ultrasound transducer detector array are housed in a hollow cylindrical geometry that rotates 360 degrees to allow multiple projections through the subject of interest placed inside the cylinder. The structural, functional, and molecular imaging capabilities of the LED–PACT system are validated using various tissue-mimicking phantom studies. The axial, lateral, and elevational resolutions of the system at 2.3 cm depth are estimated as 0.12 mm, 0.3 mm, and 2.1 mm, respectively. Spectrally unmixed photoacoustic contrasts from tubes filled with oxy- and deoxy-hemoglobin, indocyanine green, methylene blue, and melanin molecules demonstrate the multispectral molecular imaging capabilities of the system. Human-finger-mimicking phantoms made of a bone and blood tubes show structural and functional oxygen saturation imaging capabilities. Together, these results demonstrate the potential of the proposed LED-based, low-cost, portable PACT system for pre-clinical and clinical applications.

Sign in / Sign up

Export Citation Format

Share Document