scholarly journals A Low-Cost Chamber Prototype for Automatic Thermal Analysis of MEMS IMU Sensors in Tilt Measurements Perspective

Sensors ◽  
2019 ◽  
Vol 19 (12) ◽  
pp. 2705
Author(s):  
Giuseppe Ruzza ◽  
Luigi Guerriero ◽  
Paola Revellino ◽  
Francesco M. Guadagno
Keyword(s):  
Thermal Analysis ◽  
Thermal Behavior ◽  
Low Cost ◽  
Measurement Unit ◽  
Peltier Element ◽  
Micro Electro Mechanical Systems ◽  
Thermal Cell ◽  
3D Printed ◽  
Mems Imu ◽  
System Prototype

In this work, a low-cost, open-source and replicable system prototype for thermal analysis of low-cost Micro Electro-Mechanical Systems (MEMS) Inertial Measurement Unit (IMU) sensors in tilt measurement perspective is presented and tested. The system is formed of a 3D printed frame, a thermal cell consisting in a Peltier element mounted over a heat sink, and a control and power system. The frame is designed to allow the independent biaxial tilting of the thermal cell through two servomotors. The control board is formed by an Arduino® and a self-made board including a power drive for controlling the thermal unit and servomotors. We tested the chamber analyzing the behavior of multiple MEMS IMU onboard accelerometers suitable for measuring tilt. Our results underline the variability of the thermal behavior of the sensors, also for different sensor boards of the same model, and consequently the need for the adoption of a thermal compensation strategy based on thermal analysis results. These data suggesting the need for the analysis of the thermal behavior of MEMS-based sensors, indicate the potential of our system in making low-cost sensors suitable in medium-to-high precision monitoring applications.

scholarly journals Augmentation of GNSS by Low-Cost MEMS IMU, OBD-II, and Digital Altimeter for Improved Positioning in Urban Area

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3830 ◽  
Author(s):  
JoonHoo Lim ◽  
Won Yoo ◽  
La Kim ◽  
You Lee ◽  
Hyung Lee
Keyword(s):  
Urban Area ◽  
Time Synchronization ◽  
Low Cost ◽  
Satellite System ◽  
Adaptive Synchronization ◽  
Measurement Unit ◽  
Micro Electro Mechanical Systems ◽  
Improved Performance ◽  
Global Navigation Satellite ◽  
Mems Imu

This paper proposes an efficient multi-sensor system to complement GNSS (Global Navigation Satellite System) for improved positioning in urban area. The proposed system augments GNSS by low-cost MEMS IMU (Micro Electro Mechanical Systems Inertial Measurement Unit), OBD (On-Board Diagnostics)-II, and digital altimeter modules. For improved availability of time synchronization in urban area, an adaptive synchronization method is proposed to combine the external PPS (Pulse Per Second) signal and the internal onboard clock. For improved positioning accuracy and availability, a 17-state Kalman filter is formulated for efficient multi-sensor fusion, including OBD-II and digital altimeter modules. A strategy to apply different types of measurement updates is also proposed for improved performance in urban area. Four experiment results with field-collected measurements evaluates the performance of the proposed GNSS/IMU/OBD-II/altimeter system in various aspects, including accuracy, precision, continuity, and availability.

scholarly journals MEMS Based SINS/OD Filter for Land Vehicles’ Applications

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Huisheng Liu ◽  
Zengcai Wang ◽  
Susu Fang ◽  
Chao Li
Keyword(s):  
Navigation System ◽  
Velocity Measurement ◽  
Microelectromechanical Systems ◽  
Low Cost ◽  
Detection Algorithm ◽  
Measurement Unit ◽  
Integrated Navigation ◽  
Integrated Navigation System ◽  
Land Vehicles ◽  
Mems Imu

A constrained low-cost SINS/OD filter aided with magnetometer is proposed in this paper. The filter is designed to provide a land vehicle navigation solution by fusing the measurements of the microelectromechanical systems based inertial measurement unit (MEMS IMU), the magnetometer (MAG), and the velocity measurement from odometer (OD). First, accelerometer and magnetometer integrated algorithm is studied to stabilize the attitude angle. Next, a SINS/OD/MAG integrated navigation system is designed and simulated, using an adaptive Kalman filter (AKF). It is shown that the accuracy of the integrated navigation system will be implemented to some extent. The field-test shows that the azimuth misalignment angle will diminish to less than 1°. Finally, an outliers detection algorithm is studied to estimate the velocity measurement bias of the odometer. The experimental results show the enhancement in restraining observation outliers that improves the precision of the integrated navigation system.

scholarly journals Performance Enhancement of Pedestrian Navigation Systems Based on Low-Cost Foot-Mounted MEMS-IMU/Ultrasonic Sensor

Sensors ◽  
2019 ◽  
Vol 19 (2) ◽  
pp. 364 ◽  
Author(s):  
Ming Xia ◽  
Chundi Xiu ◽  
Dongkai Yang ◽  
Li Wang
Keyword(s):  
Kalman Filter ◽  
Extended Kalman Filter ◽  
Navigation System ◽  
Low Cost ◽  
Ultrasonic Sensor ◽  
Measurement Unit ◽  
Positioning Error ◽  
Process Noise ◽  
Pedestrian Navigation ◽  
Mems Imu

The pedestrian navigation system (PNS) based on inertial navigation system-extended Kalman filter-zero velocity update (INS-EKF-ZUPT or IEZ) is widely used in complex environments without external infrastructure owing to its characteristics of autonomy and continuity. IEZ, however, suffers from performance degradation caused by the dynamic change of process noise statistics and heading estimation errors. The main goal of this study is to effectively improve the accuracy and robustness of pedestrian localization based on the integration of the low-cost foot-mounted microelectromechanical system inertial measurement unit (MEMS-IMU) and ultrasonic sensor. The proposed solution has two main components: (1) the fuzzy inference system (FIS) is exploited to generate the adaptive factor for extended Kalman filter (EKF) after addressing the mismatch between statistical sample covariance of innovation and the theoretical one, and the fuzzy adaptive EKF (FAEKF) based on the MEMS-IMU/ultrasonic sensor for pedestrians was proposed. Accordingly, the adaptive factor is applied to correct process noise covariance that accurately reflects previous state estimations. (2) A straight motion heading update (SMHU) algorithm is developed to detect whether a straight walk happens and to revise errors in heading if the ultrasonic sensor detects the distance between the foot and reflection point of the wall. The experimental results show that horizontal positioning error is less than 2% of the total travelled distance (TTD) in different environments, which is the same order of positioning error compared with other works using high-end MEMS-IMU. It is concluded that the proposed approach can achieve high performance for PNS in terms of accuracy and robustness.

scholarly journals Design and Implementation of an AHRS Based on MEMS Sensors and Complementary Filtering

2014 ◽  
Vol 6 ◽  
pp. 214726 ◽  
Author(s):  
Yangzhu Wang ◽  
Ning Li ◽  
Xi Chen ◽  
Miao Liu
Keyword(s):  
Low Cost ◽  
Low Frequency ◽  
Measurement Unit ◽  
Accurate Estimation ◽  
Extended Kalman Filtering ◽  
Mems Sensors ◽  
Features Fusion ◽  
Design And Implementation ◽  
Mems Imu ◽  
Experimental Comparisons

This paper presents design and implementation of an attitude and heading reference system (AHRS) based on low-cost MEMS sensors and complementary filtering (CF). Different from traditional solutions, information fusion is performed with Euler angles directly, which is more straightforward for understanding; however it proposes many challenges for reaching a stable and accurate estimation as when these angles approach or traverse their range boundaries, estimation may get discontinuous. Thus an effective discontinuity avoiding strategy is suggested in this paper to refine the estimation. Besides, instead of extended Kalman filtering (EKF), CF is utilized for state estimation of AHRS as it features fusion of high-frequency and low-frequency signals. In order to make up for shortcomings of MEMS sensors such as multiple errors, drifts, and bad accuracy, some effective calibration and filtering algorithms are proposed to guarantee agreeable AHRS performance. Also, architecture of the MEMS IMU (inertial measurement unit) and mathematical principles for AHRS solution are explained and implemented in this paper. Meanwhile, experimental comparisons have proved feasibility and acceptable performance of this AHRS design.

scholarly journals Low-Cost Navigation and Guidance Systems for Unmanned Aerial Vehicles — Part 1: Vision-Based and Integrated Sensors

2012 ◽  
Vol 19 (2) ◽  
pp. 71-98 ◽  
Author(s):  
Roberto Sabatini ◽  
Celia Bartel ◽  
Anish Kaharkar ◽  
Tesheen Shaid ◽  
Leopoldo Rodriguez ◽  
...  
Keyword(s):  
Unmanned Aerial Vehicles ◽  
System Architecture ◽  
Navigation System ◽  
Low Cost ◽  
Measurement Unit ◽  
Integrated Navigation ◽  
Integrated Navigation System ◽  
Aerial Vehicles ◽  
Vision Based Navigation ◽  
Mems Imu

Abstract In this paper we present a new low-cost navigation system designed for small size Unmanned Aerial Vehicles (UAVs) based on Vision-Based Navigation (VBN) and other avionics sensors. The main objective of our research was to design a compact, light and relatively inexpensive system capable of providing the Required Navigation Performance (RNP) in all phases of flight of a small UAV, with a special focus on precision approach and landing, where Vision Based Navigation (VBN) techniques can be fully exploited in a multisensor integrated architecture. Various existing techniques for VBN were compared and the Appearance-Based Approach (ABA) was selected for implementation. Feature extraction and optical flow techniques were employed to estimate flight parameters such as roll angle, pitch angle, deviation from the runway and body rates. Additionally, we addressed the possible synergies between VBN, Global Navigation Satellite System (GNSS) and MEMS-IMU (Micro-Electromechanical System Inertial Measurement Unit) sensors, as well as the aiding from Aircraft Dynamics Models (ADMs). In particular, by employing these sensors/models, we aimed to compensate for the shortcomings of VBN and MEMS-IMU sensors in high-dynamics attitude determination tasks. An Extended Kalman Filter (EKF) was developed to fuse the information provided by the different sensors and to provide estimates of position, velocity and attitude of the UAV platform in real-time. Two different integrated navigation system architectures were implemented. The first used VBN at 20 Hz and GPS at 1 Hz to augment the MEMS-IMU running at 100 Hz. The second mode also included the ADM (computations performed at 100 Hz) to provide augmentation of the attitude channel. Simulation of these two modes was accomplished in a significant portion of the AEROSONDE UAV operational flight envelope and performing a variety of representative manoeuvres (i.e., straight climb, level turning, turning descent and climb, straight descent, etc.). Simulation of the first integrated navigation system architecture (VBN/IMU/GPS) showed that the integrated system can reach position, velocity and attitude accuracies compatible with CAT-II precision approach requirements. Simulation of the second system architecture (VBN/IMU/GPS/ADM) also showed promising results since the achieved attitude accuracy was higher using the ADM/VBS/IMU than using VBS/IMU only. However, due to rapid divergence of the ADM virtual sensor, there was a need for frequent re-initialisation of the ADM data module, which was strongly dependent on the UAV flight dynamics and the specific manoeuvring transitions performed

scholarly journals Artificial Marker and MEMS IMU-Based Pose Estimation Method to Meet Multirotor UAV Landing Requirements

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5428 ◽  
Author(s):  
Yibin Wu ◽  
Xiaoji Niu ◽  
Junwei Du ◽  
Le Chang ◽  
Hailiang Tang ◽  
...  
Keyword(s):  
Pose Estimation ◽  
Degrees Of Freedom ◽  
Field Experiments ◽  
Low Cost ◽  
Estimation Method ◽  
Measurement Unit ◽  
Vertical Position ◽  
Autonomous Operation ◽  
Micro Electromechanical System ◽  
Mems Imu

The fully autonomous operation of multirotor unmanned air vehicles (UAVs) in many applications requires support of precision landing. Onboard camera and fiducial marker have been widely used for this critical phase due to its low cost and high effectiveness. This paper proposes a six-degrees-of-freedom (DoF) pose estimation solution for UAV landing based on an artificial marker and a micro-electromechanical system (MEMS) inertial measurement unit (IMU). The position and orientation of the landing maker are measured in advance. The absolute position and heading of the UAV are estimated by detecting the marker and extracting corner points with the onboard monocular camera. To achieve continuous and reliable positioning when the marker is occasionally shadowed, IMU data is fused by an extended Kalman filter (EKF). The error terms of the IMU sensor are modeled and estimated. Field experiments show that the positioning accuracy of the proposed system is at centimeter level, and the heading error is less than 0.1 degrees. Comparing to the marker-based approach, the roll and pitch angle errors decreased by 33% and 54% on average. Within five seconds of vision outage, the average drifts of the horizontal and vertical position were 0.41 and 0.09 m, respectively.

Wireless Input Technology Based on MEMS Inertial Measurement Unit - A Survey

2017 ◽  
Vol 870 ◽  
pp. 79-84
Author(s):  
Zhen Xian Fu ◽  
Guang Ying Zhang ◽  
Yu Rong Lin ◽  
Yang Liu
Keyword(s):  
Inertial Measurement Unit ◽  
Inertial Sensors ◽  
Inertial Sensor ◽  
Low Cost ◽  
Propagation Model ◽  
Measurement Unit ◽  
Input Device ◽  
Operational Environment ◽  
Inertial Measurement ◽  
Mems Imu

Rapid progress in Micro-Electromechanical System (MEMS) technique is making inertial sensors increasingly miniaturized, enabling it to be widely applied in people’s everyday life. Recent years, research and development of wireless input device based on MEMS inertial measurement unit (IMU) is receiving more and more attention. In this paper, a survey is made of the recent research on inertial pens based on MEMS-IMU. First, the advantage of IMU-based input is discussed, with comparison with other types of input systems. Then, based on the operation of an inertial pen, which can be roughly divided into four stages: motion sensing, error containment, feature extraction and recognition, various approaches employed to address the challenges facing each stage are introduced. Finally, while discussing the future prospect of the IMU-based input systems, it is suggested that the methods of autonomous and portable calibration of inertial sensor errors be further explored. The low-cost feature of an inertial pen makes it desirable that its calibration be carried out independently, rapidly, and portably. Meanwhile, some unique features of the operational environment of an inertial pen make it possible to simplify its error propagation model and expedite its calibration, making the technique more practically viable.

scholarly journals Performance Assessment of an Ultra Low-Cost Inertial Measurement Unit for Ground Vehicle Navigation

Sensors ◽  
2019 ◽  
Vol 19 (18) ◽  
pp. 3865 ◽  
Author(s):  
Rodrigo Gonzalez ◽  
Paolo Dabove
Keyword(s):  
Automotive Industry ◽  
Inertial Measurement Unit ◽  
Microelectromechanical Systems ◽  
Inertial Sensor ◽  
Low Cost ◽  
Measurement Unit ◽  
Navigation Systems ◽  
Mass Market ◽  
Inertial Measurement ◽  
Mems Imu

Nowadays, navigation systems are becoming common in the automotive industry due to advanced driver assistance systems and the development of autonomous vehicles. The MPU-6000 is a popular ultra low-cost Microelectromechanical Systems (MEMS) inertial measurement unit (IMU) used in several applications. Although this mass-market sensor is used extensively in a variety of fields, it has not caught the attention of the automotive industry. Moreover, a detailed performance analysis of this inertial sensor for ground navigation systems is not available in the previous literature. In this work, a deep examination of one MPU-6000 IMU as part of a low-cost navigation system for ground vehicles is provided. The steps to characterize the performance of the MPU-6000 are divided in two phases: static and kinematic analyses. Besides, an additional MEMS IMU of superior quality is also included in all experiments just for the purpose of comparison. After the static analysis, a kinematic test is conducted by generating a real urban trajectory registering an MPU-6000 IMU, the higher-grade MEMS IMU, and two GNSS receivers. The kinematic trajectory is divided in two parts, a normal trajectory with good satellites visibility and a second part where the Global Navigation Satellite System (GNSS) signal is forced to be lost. Evaluating the attitude and position inaccuracies from these two scenarios, it is concluded in this preliminary work that this mass-market IMU can be considered as a convenient inertial sensor for low-cost integrated navigation systems for applications that can tolerate a 3D position error of about 2 m and a heading angle error of about 3 °.

scholarly journals Validation of Low-Cost Pavement Monitoring Inertial Sensor for Urban Road Network

2021 ◽  
Author(s):  
Giuseppe Loprencipe ◽  
Flavio Guilherme Vaz de Almeida Filho ◽  
Rafael Henrique de Oliveira ◽  
Salvatore Bruno
Keyword(s):  
Ride Comfort ◽  
Inertial Sensor ◽  
Low Cost ◽  
Road Networks ◽  
Measurement Unit ◽  
Raspberry Pi ◽  
Micro Electro Mechanical Systems ◽  
The Road ◽  
Comfort Index ◽  
Rolling Noise

Road networks are monitored to evaluate their decay level and the performances regarding ride comfort, vehicle rolling noise, fuel consumption, etc. In this study, an Inertial Measurement Unit is proposed by using a low-cost three-axis Micro-Electro-Mechanical Systems accelerometer and a GPS instrument, which are connected to a Raspberry Pi Zero W board and embedded inside a vehicle to monitor indirectly the road condition. To assess the level of pavement decay, the comfort index awz defined by the ISO 2631 standard was considered. Considering 21 km of roads, with different levels of pavement decay, validation measures made using the proposed IMU, another pre-assembled IMU, and a Road Surface Profiler were performed. Therefore, comparisons between awz determined with accelerations measured on the two different IMU are made; in addition, also correlations between awz, International Roughness Index (IRI), and Ride Number (RN) were performed. The results were shown very good correlations between the awz calculated with the proposed IMU and ones in the other IMU. In addition, the correlations between awz and IRI and RN were showed promising results, considering the use and the costs of the proposed IMU as a reliable method to assess the pavements decay in road networks where the use of traditional systems is difficult and/or not cheap.

scholarly journals A Novel Fault-Tolerant Navigation and Positioning Method with Stereo-Camera/Micro Electro Mechanical Systems Inertial Measurement Unit (MEMS-IMU) in Hostile Environment

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 626 ◽  
Author(s):  
Cheng Yuan ◽  
Jizhou Lai ◽  
Pin Lyu ◽  
Peng Shi ◽  
Wei Zhao ◽  
...  
Keyword(s):  
Inertial Measurement Unit ◽  
Fault Tolerant ◽  
Mechanical Systems ◽  
Measurement Unit ◽  
Hostile Environment ◽  
Micro Electro Mechanical Systems ◽  
Inertial Measurement ◽  
Stereo Camera ◽  
Positioning Method ◽  
Mems Imu

Visual odometry (VO) is a new navigation and positioning method that estimates the ego-motion of vehicles from images. However, VO with unsatisfactory performance can fail severely in hostile environment because of the less feature, fast angular motions, or illumination change. Thus, enhancing the robustness of VO in hostile environment has become a popular research topic. In this paper, a novel fault-tolerant visual-inertial odometry (VIO) navigation and positioning method framework is presented. The micro electro mechanical systems inertial measurement unit (MEMS-IMU) is used to aid the stereo-camera, for a robust pose estimation in hostile environment. In the algorithm, the MEMS-IMU pre-integration is deployed to improve the motion estimation accuracy and robustness in the cases of similar or few feature points. Besides, a dramatic change detector and an adaptive observation noise factor are introduced, tolerating and decreasing the estimation error that is caused by large angular motion or wrong matching. Experiments in hostile environment showing that the presented method can achieve better position estimation when compared with the traditional VO and VIO method.

Sign in / Sign up

Export Citation Format

Share Document