scholarly journals A Frequency Signature RFID Chipless Tag for Wearable Applications

Sensors ◽  
2019 ◽  
Vol 19 (3) ◽  
pp. 494 ◽  
Author(s):  
Laura Corchia ◽  
Giuseppina Monti ◽  
Luciano Tarricone
Keyword(s):  
Radio Frequency Identification ◽  
Microstrip Line ◽  
Ground Plane ◽  
Experimental Tests ◽  
Seamless Integration ◽  
Resonator Structure ◽  
Compact Size ◽  
Monopole Antennas ◽  
Frequency Identification ◽  
Easy Integration

In this paper, a frequency-signature Radio-Frequency Identification (RFID) chipless tag for wearable applications is presented. The results achieved for a fully-textile solution guaranteeing a seamless integration in clothes are reported and discussed. The proposed tag consists of two planar monopole antennas and a 50 Ω microstrip line loaded with multiple resonators. In order to achieve a compact size, the resonators are slotted on the ground plane of the microstrip line. As for the antennas, the same geometry was exploited for both the TX and the RX tag antenna. In particular, it consists of a proximity fed planar monopole on a ground plane. The selected geometry guarantees easy integration with the multi-resonator structure. Numerical and experimental data referring to a 2-bit implementation are presented and discussed. For fabricating all the prototypes, a layer of pile was used as a substrate, while an adhesive non-woven conductive fabric was exploited for the fabrication of the conductive parts. Experimental tests demonstrate that although the performance of the final device strongly depends on the properties of the used materials and on the imperfections of the fabrication process, the proposed frequency-signature RFID chipless tag is suitable for wearable applications, such as anti-counterfeiting systems and laundry labels.

scholarly journals Compact Circularly Polarized Multiband Antennas for RFID Applications

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
H. M. El Misilmani ◽  
M. Al-Husseini ◽  
K. Y. Kabalan ◽  
A. El-Hajj
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Microstrip Line ◽  
Ground Plane ◽  
Dual Band ◽  
Circularly Polarized ◽  
Multiband Antennas ◽  
Compact Size ◽  
Frequency Identification ◽  
Rfid Applications

This paper presents multiband circularly polarized (CP) antennas for radio frequency identification (RFID). A coax-fed and a microstrip-line-fed antennas having optimized cross-slots in their patches are first designed for dual-band CP operation. The microstrip-line-fed design is then modified, by incorporating a U-shaped slot in its partial ground plane, to achieve additional operation band with a CP characteristic. Simulation and measured results of the presented designs are reported. The measured results are in accordance with the computed ones. The compact size and CP property make these designs suitable for RFID applications.

Adaptive Framework for Collisions in RFID Tag Identification

2008 ◽  
Vol 07 (01) ◽  
pp. 9-14 ◽  
Author(s):  
Selwyn Piramuthu
Keyword(s):  
Supply Chain ◽  
Radio Frequency Identification ◽  
Rfid Tags ◽  
Tag Identification ◽  
Seamless Integration ◽  
Essential Information ◽  
Rfid Tag ◽  
Frequency Identification ◽  
Pass Through ◽  
Aloha Protocol

Radio Frequency Identification (RFID) is promising, as a technique, to enable tracking of essential information about objects as they pass through supply chains. Information thus tracked can be utilised to efficiently operate the supply chain. Effective management of the supply chain translates to huge competitive advantage for the firms involved. Among several issues that impede seamless integration of RFID tags in a supply chain, one of the problems encountered while reading RFID tags is that of collision, which occurs when multiple tags transmit data to the same receiver slot. Data loss due to collision necessitates re-transmission of lost data. We consider this problem when Framed Slotted ALOHA protocol is used. Using machine learning, we adaptively configure the number of slots per frame to reduce the number of collisions while improving throughput.

Utilizing Modeling in a Reliability Study of ACA Joints in Humidity Tests

2013 ◽  
Vol 10 (1) ◽  
pp. 30-39 ◽  
Author(s):  
Kirsi Saarinen ◽  
Laura Frisk
Keyword(s):  
Radio Frequency Identification ◽  
Cost Savings ◽  
Experimental Tests ◽  
Shear Stresses ◽  
Cycling Test ◽  
Humidity Level ◽  
Anisotropic Conductive Adhesive ◽  
Frequency Identification ◽  
Identification Tags ◽  
Selection Of

Radio frequency identification tags (RFID) with anisotropic conductive adhesive (ACA) joints are used in various applications where the environmental conditions may impair their reliability. Thus the effects of different environmental stresses on reliability need to be investigated. The purpose of this work was to study whether a relatively simple shear stress model can be utilized in reliability prediction of anisotropically conductive paste (ACP) joints in an accelerated humidity test on the basis of the information obtained from another humidity test. If modeling gives accurate results when studying reliability, the need for actual testing would decrease and thereby time and cost savings could be achieved. In this study, finite element models were made to calculate shear stresses in ACP joints induced by two different humidity tests. Additionally, experimental tests were performed and the results were compared with those of modeling. The test samples were RFID tags whose microchips were attached with ACP. A constant humidity test was used to study the effects of high humidity level and a humidity cycling test was used to examine the effects of constantly varying humidity. In the modeling it was observed that the selection of the stress-free temperature has a significant effect on the results. With three different stress-free temperatures, three different sets of results were obtained. Although the tags saturated in the extreme conditions of the humidity cycling test, according to modeling, the change in relative humidity level in the humidity cycling test did not increase the harshness of the test. However, the temperature change in the humidity cycling test increased the harshness.

scholarly journals Four-State Coupled-Line Resonator for Chipless RFID Tags Application

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 581 ◽  
Author(s):  
Wazie M. Abdulkawi ◽  
Abdel-Fattah A. Sheta
Keyword(s):  
Dielectric Constant ◽  
Radio Frequency Identification ◽  
Rfid Tags ◽  
Microstrip Resonator ◽  
Coupled Line ◽  
Chipless Rfid ◽  
Compact Size ◽  
Frequency Identification ◽  
The Cost ◽  
Good Agreement

A novel quad-state coupled-line microstrip resonator is proposed for compact chipless radio frequency identification (RFID) tags. The proposed resonator can be reconfigured to present one of four possible states: 00, 01, 10, and 11, representing, no resonance, resonance at f2, resonance at f1, and resonance at both f1 and f2, respectively. The frequency span between f2 and f1 can be easily controlled, thereby reducing the required spectrum. Moreover, the proposed technique allows the storage of a large amount of data in a compact size to reduce the cost per bit. A multi-resonator prototype consisting of six resonators is designed, analyzed, and experimentally characterized. This prototype is implemented on the RT Duroid 5880 substrate with a dielectric constant of 2.2, loss tangent of 0.0009, and thickness of 0.79 mm. The designed configuration can be reconfigured for 46 codes. Two complete the RFID tags, including the six resonators and two orthogonally polarized transmitting and receiving antennas, are implemented and tested. The first tag code is designed for all ones, 111111111111, and the second tag is designed as 101010101010 code. Experimental results show good agreement with the simulation.

scholarly journals Optimization of UHF RFID Five-Slotted Patch Tag Design Using PSO Algorithm for Biomedical Sensing Systems

2020 ◽  
Vol 17 (22) ◽  
pp. 8593
Author(s):  
Ibtissame Bouhassoune ◽  
Abdellah Chehri ◽  
Rachid Saadane ◽  
Khalid Minaoui
Keyword(s):  
Human Body ◽  
Radio Frequency Identification ◽  
Flexible Substrate ◽  
Ground Plane ◽  
Pso Algorithm ◽  
Uhf Rfid ◽  
Biomedical Sensing ◽  
Sensing Applications ◽  
Human Arm ◽  
Frequency Identification

In this paper, a new flexible wearable radio frequency identification (RFID) five-shaped slot patch tag placed on the human arm is designed for ultra-high frequency (UHF) healthcare sensing applications. The compact proposed tag consists of a patch structure provided with five shaped slot radiators and a flexible substrate, which minimize the human body’s impact on the antenna radiation performance. We have optimized our designed tag using the particle swarm optimization (PSO) method with curve fitting within MATLAB to minimize antenna parameters to achieve a good return loss and an attractive radiation performance in the operating band. The PSO-optimized tag’s performance has been examined over the specific placement in some parts of the human body, such as wrist and chest, to evaluate the tag response and enable our tag antenna conception in wearable biomedical sensing applications. Finally, we have tested the robustness of this tag by evaluating its sensitivity as a function of the antenna radiator placement over the ground plane or by shaping the ground plane substrate for the tag’s position from the human body. Our numerical results show an optimal tag size with good matching features and promising read ranges near the human body.

scholarly journals A Novel Compact CP Antenna with Wide Axial Ratio Bandwidth for Worldwide UHF RFID Handheld Reader

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Waleed Abdelrahim Ahmed ◽  
Feng Quanyuan
Keyword(s):  
Radio Frequency Identification ◽  
Low Cost ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Axial Ratio ◽  
Plane Layer ◽  
Impedance Bandwidth ◽  
Uhf Rfid ◽  
Frequency Identification ◽  
The Right

This study presents a novel compact circularly polarized antenna for universal ultrahigh-frequency (UHF) radio-frequency identification (RFID) handheld reader applications. The antenna is composed of a coplanar waveguide (CPW) L-shaped feedline mounted at the right edge of the square slot at the bottom of the ground plane to realize a circular polarization; a horizontal stub protruded from the right side of the square slot towards the slot centre, and a vertical stub is mounted at the lower left of the square slot. The designed antenna printed on one ground plane layer of a low-cost FR4 substrate with an overall size of 120×120×1.6 mm3. The measurement results show indicate that the fabricated antenna achieves a wide axial ratio (AR) bandwidth of 460 MHz (818–1278 MHz), wide impedance bandwidth of 54.6% (630–1103 MHz), and a measured peak gain of 4.0 dBi. The proposed antenna is a good candidate for compact universal UHF RFID handheld reader applications (840–960 MHz).

scholarly journals Design a Compact Coplanar Wideband Antenna Used in Radio Frequency Identification Systems

2020 ◽  
Vol sceeer (3d) ◽  
pp. 134-138
Author(s):  
Sufyan Ali ◽  
Ahmed Reja ◽  
Yousif Hachim
Keyword(s):  
Resonant Frequency ◽  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Return Loss ◽  
Ground Plane ◽  
Substrate Material ◽  
Tangent Loss ◽  
Frequency Interval ◽  
Dielectric Thickness ◽  
Frequency Identification

In this paper, a new compact coplanar antenna used for Radio frequency identification (FID) applications is presented. This antenna is operated at the resonant frequency of 2.45 GHz. The proposed antenna is designed on an epoxy substrate material type (FR-4) with small size of (40 × 28) mm2 in which the dielectric thickness (ℎ) of 1.6 mm, relative permittivity (er) of 4.3 and tangent loss of 0.025. In this design the return loss is less than −10 dB in the frequency interval (2.12 − 2.84) GHz and the minimum value of return loss is -32 dB at resonant frequency. The maximum gain of the proposed antenna is 1.22 dB and the maximum directivity obtained is 2.27 dB. The patch and the ground plane of the proposed antenna are in the same surface. The proposed antenna has a wide bandwidth and omnidirectional radiation pattern with small size. The overall size of the compact antenna is (40 × 28 × 1.635) mm3. The Computer Simulation Technology (CST) microwave studio software is used for simulation and gets layout design.

scholarly journals Design of Compact Tri-Band Fractal Antenna for RFID Readers

2017 ◽  
Vol 7 (4) ◽  
pp. 2036 ◽  
Author(s):  
Mohamed Ihamji ◽  
Elhassane Abdelmounim ◽  
Hamid Bennis ◽  
Mostafa Hefnawi ◽  
Mohamed Latrach
Keyword(s):  
Radio Frequency ◽  
Radiation Pattern ◽  
Radio Frequency Identification ◽  
Input Impedance ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
Physical Parameters ◽  
Fractal Antenna ◽  
Frequency Identification ◽  
Rectangular Microstrip Antenna

In this paper, a multiband and miniature rectangular microstrip antenna is designed and analyzed for Radio Frequency Identification (RFID) reader applications. The miniaturization is achieved using fractal technique and the physical parameters of the structure as well as its ground plane are optimized using CST Microwave Studio. The total area of the final structure is 71.6 x 94 mm<sup>2</sup>. The results show that the proposed antenna has good matching input impedance with a stable radiation pattern at 915 MHz, 2.45 GHz, and 5.8 GHz.

Design of Circular Patch Microstrip Antenna with Egg Slot for 2.4 GHz Ultra-Wideband Radio Frequency Identification (UWB RFID) Tag Applications

2014 ◽  
Vol 513-517 ◽  
pp. 3414-3418 ◽  
Author(s):  
Yuwono Rudy ◽  
Dwi A. Wahyu ◽  
Fauzan Edy P. Muhammad
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
White Paper ◽  
Ultra Wideband ◽  
Rfid Tag ◽  
Circular Patch ◽  
Frequency Identification ◽  
Circular Microstrip Antenna

This paper discusses concerning design of circular patch microstrip antenna for Radio Frequency Identification (RFID) tags application in microwave band. Circular microstrip antenna is designed with an egg slot on the ground plane and feed line to get ultra wideband. The design of microstrip antenna using Phenolic White Paper-FR2 with dielectric constant (or) =4.5. Based on simulation results, the antenna shows it works at frequency 2128-4807 MHz with gain of-17,398 dBi. The rectangular stub, caused the decreasing of bandwidth but the gain increase. By adding a rectangular stub on the ground plane, antenna works at frequency 1166 3475 MHz with increasing gain of-2,733 dBi.

scholarly journals Unidirectional Dual-Band CPW-Fed Antenna Loaded with an AMC Reflector

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Qun Luo ◽  
Huiping Tian ◽  
Zhitong Huang ◽  
Xudong Wang ◽  
Zheng Guo ◽  
...  
Keyword(s):  
Radio Frequency Identification ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Dielectric Substrate ◽  
Dual Band ◽  
Magnetic Conductor ◽  
Suitable Candidate ◽  
Gain Enhancement ◽  
Low Profile ◽  
Frequency Identification

A unidirectional dual-band coplanar waveguide fed antenna (DB-CPWFA) loaded with a reflector is presented in this paper. The reflector is made of an electric ground plane, a dielectric substrate, and artificial magnetic conductor (AMC) which shows an effective dual operational bandwidth. Then, the closely spaced AMC reflector is employed under the DB-DPWFA for performance improvement including unidirectional radiation, low profile, gain enhancement, and higher front-to-back (F/B) ratio. The final antenna design exhibits an 8% and 13% impedance bandwidths for 2.45 GHz and 5.8 GHz frequency regions, respectively. The overall gain enhancement of about 4 dB is achieved. The F/B ratio is approximate to 20 dB with a 16 dB improvement. The measured results are inconsistent with the numerical values. The presented design is a suitable candidate for radio frequency identification (RFID) reader application.

Sign in / Sign up

Export Citation Format

Share Document